Xit XTCG6D Handleiding

Xit Overige camera toebehoren XTCG6D

Lees hieronder de 📖 handleiding in het Nederlandse voor Xit XTCG6D (1 pagina's) in de categorie Overige camera toebehoren. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

PART NAMES

1. Protective cover

2. Electrical contacts

3. Attachment screw

4. Guide pin

5. Attach/detach knob

6. Battery magazine release handle

7. DC cord mount

8. AF point selection/Magnify button

9. AE lock/FE lock/Index/Reduce button

10. AF start button

11. Vertical-grip operation switch

12. Shutter button

13. Camera battery compartment cover slot

14. Main dial

15. Hand strap mount

16. Tripod socket

17. Battery chamber latch

18. Battery pack compartment

19. Battery magazine (for size-AA batteries)

1 2 3-1 3-2

4 5 6

7-1 7-2 8 9-1 9-2

10 11 12

The XTCG6D is a battery grip that can hold two battery pack

LP-E6 or six-AA batteries, it is also equipped with a vertical-grip

shutter button, main dial, etc to enable shooting in the same way

as with horizontal grip.

1. Remove the battery from the camera. (Fig. 1)

2. Pull out the camera’s battery compartment cover a slanted

angle to detach. (Fig. 2)

Perform the operation on a table so as not to drop the

camera.

3. Insert the detached cover into its storage slot to ensure that

it will not be lost. (Fig.3)

When taking out the cover, press lightly on the cover hinge

and pull it out upward at a slanted angle. (Fig.3-2)

4. Remove the protective cover, and then insert the electrical

contacts into the camera battery compartment. (Fig.4-1)

5. Align the attachment screw with the camera’s tripod socket.

And then turn the attach/detach knob to tighten securely.

(Fig. 4-1)

1. After ipping out the release handle, turn it as shown by the

arrow. Then pull out the battery magazine (for size-AA/LR6

batteries). (Fig. 5)

2. Insert one or two battery pack LP-E6 into the battery

magazine (for LP-E6) (Fig. 6)

3. Attach the battery magazine into the battery grip. (Fig. 7-1)

After attaching, check that the battery magazine is securely

attached to the battery grip.

4. Close the release handle. (Fig. 7-2)

• Do not further push open the battery compartment cover when

it is already open, doing so may damage its hinge.

• Be sure to attach the battery grip to the camera before inserting

the batteries. The results of the battery check may not be

displayed properly if you attach the battery grip to the camera

with the batteries already inside.

• Before removing the battery grip from the camera, make sure to

turn the camera’s power switch to <OFF>, and take out the

batteries. After removing the batteries, attach the protective

cover to the electrical contacts.

• Fewer images can be shot when using size-AA batteries. Also, the

number of possible shots may vary depending on the batteries

brand and storage conditions. So age of size-AA batteries is

recommended only for emergencies.

• With size-AA batteries, use six new batteries of the same brand at

temperature above 20°C / 68°F, the camera may not function when

used in lower temperature or when old and new batteries are used

together.

• If only one battery pack is used, it can be inserted in either the

right or left side.

• If two battery packs are inserted, power is supplied

simultaneously by both battery packs. Two battery packs with

dierent charging levels can be inserted and used without any

problems.

• Remove the battery packs or size-AA batteries from the battery

grip when the camera will not be used for an extended period.

ATTACHING TO THE CAMERA

INSTALLING THE BATTERY PACKS

1. Insert the batteries onto the battery magazine (for size-AA

batteries). (Fig. 8)

Make sure the + and - battery contacts are properly

oriented as shown in the illustration.

2. Attach the battery magazine into the battery grip. (Fig. 9-1)

After attaching, check that the battery magazine is

securely attached to the battery grip.

3. Close the release handle. (Fig. 9-2)

INSTALLING SIZE-AA BATTERIES

1. Turning the vertical-grip operation switch to <ON> (Fig.12)

makes the battery grip buttons and dial function in the

same way as those on the camera.

2. When shooting in the horizontal-grip position, turn the

vertical-grip operation switch to <OFF> so that you do not

accidentally use the buttons or dial on the battery grip.

3. The battery level can be checked on the camera.

USING THE BATTERY GRIP

SPECIFICATIONS

Battery

Power switch

Possible shots

Working temperature

range

Working humidity

Dimensions

Weight

1) One or two battery packs LP-E6

2) Six size-AA alkaline batteries

Camera’s power switch

Refer to your camera’s instruction manual

0°C - + 40°C / 32°F - 104°F

85% or less

Approx. 145.6 (W) x 111.3 (H) x 85.3 (D) mm

Approx. 5.7 (W) x 4.4 (H) x 3.4 (D) in

Approx. 295g / 10.4oz (without batteries and battery

magazine)

Canon

Product specificaties

Merk:	Xit
Categorie:	Overige camera toebehoren
Model:	XTCG6D
Kleur van het product:	Zwart
Gebruikershandleiding:	Ja
Ondersteund aantal accu's/batterijen:	8
Merkcompatibiliteit:	Canon
Compatibele producten:	Canon 6D
Type product:	Digitale camera batterijgreep
Type batterij:	LP-E6
Cylindrische batterij-grootte:	AA