Xigmatek Windpower Pro Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Xigmatek Windpower Pro (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Insert screw bolts to Intel LGA1700/1200/115x
backplate mounting holes.
Install screw bolt washers to lock the screw bolts &
backplate.
For LGA 1700 socket
Make sure the screw bolt is lock in on the backplate.
Install the backplate to motherboard.
• 安裝螺桿對準後插入
Intel LGA1700/1200/115x
強化背
板孔位
• 安裝強化背板絕緣墊片,套上螺桿後壓緊
• 請確認螺桿有正確鎖定在強化背板
• 安裝強化背板對準主機板安裝孔
Connect cooling fan 4Pin PWM connector to motherboard
CPU Fan socket.
• 安裝散熱風扇
• 請黏貼風扇扣具墊片在風扇底部兩個螺絲孔位,此墊片用於風扇上方有接觸RGB上蓋時的狀況
• 使用鐵絲風扇扣具安裝風扇,重覆相同步驟完成另一側風扇安裝
• 安裝 散熱器底座固定支架Intel
• 連接散熱風扇4Pin PWM CPU Fan接頭到主機板 孔
• 安裝散熱器對準背板螺桿後放置在CPU
• 使用彈簧螺母完成散熱器及主機板的安裝
CPU表面擠適量散熱膏,塗抹均
Align the Intel cooler base mounting brackets to backplate
screw bolts, then place the air cooler on the CPU carefully.
Using spring screw nuts to complete the air cooler and
motherboard installation.
• 移除散熱器底座保護
Install the Intel cooler base mounting brackets.
Remove cooler base protective film. Clean the CPU surface.
Stick the fan clip cushion pad the bottom of cooling fan screw holes, this only apply when top of the fan is
touching the top RGB cover.
Clip the cooling fan to the heatsink repeat again for second fan to complete the dual fan installation.
• 安裝散熱器時請移除雙風扇確保安裝過程中沒有任何零件干涉
• 如果因外觀需求或特殊主板零件干涉問題,您可以使用 Cooling Fan Installation B 方案
Please remove the dual fan before cooler installation, so there is no interference during installation.
If you like to adjust the fan position for aesthetic purpose or avoid cooling fan touching the component
with special design motherboard, please use Cooling Fan Installation B.
Intel LGA 1700/1200/115x
Install cooling fan using included fan clips.
屬風扇安裝鐵絲
Metal Wire Fan
Mounting Clips
AMD
散熱器底座固定支架
AMD Cooler Base
Mounting Bracket
Intel
散熱器底座固定支架
Intel 1700/1200/115x
Cooler Base Mounting Bracket
120mm RGB
幻彩
LED PWM
風扇
120mm RGB Rainbow
LED PWM Fan
Intel/AMD
固定支架螺絲
Intel/AMD
Mounting Bracket Screw
Intel 2011/2066
散熱器底座固定支架
Intel 2011/2066
Cooler Base Mounting Bracket
風扇扣具墊片
Fan Clip Cusion Pad
散熱膏
Thermal Paste
PWM Cable/PWM風扇線
ARGB主板同步線
ARGB Fan Cable
迷你 ARGB 控制器
B LED Controller
Intel
金屬強化背板
Intel
Reinforced Matel Backplate
LGA17XX
LGA115X
For LGA 115x/1200 socket
LGA17XX
LGA115X
熱器
ooler
Windpower Pro Accessories
Cooling Fan Installation BCooling Fan Installation A
安裝散熱風扇
連接散熱風扇
4Pin PWM
接頭到主機板
CPU Fan
孔位
移除散熱器底座保護膜
CPU清潔 表面
• CPU表面擠適量散熱膏,塗抹均勻
Remove cooler base protective film.
Clean the CPU surface.
Apply and spread the thermal paste to CPU evenly.
請確認將 線材連接散熱器的 插座 請確認主機板或風扇控制盒是 主機板同步認ARGB ARGB ARGB
AMD AM3/AM4/AM5
Make sure the ARGB cable included is connect to
ARGB socket
Please make sure the motherboard or fan control
box are ARGB MB SYNC certified
請確認將 線材連接散熱器的 插座PWM PWM
LED LED請確認將上蓋 燈板線材連接主風扇的上蓋 插座
Install the Intel cooler base mounting brackets.
Install cooling fan using included fan clips.
Connect cooling fan 4Pin PWM connector to motherboard
CPU Fan socket.
安裝Intel 2011/2066散熱器底座固定支架
Install the Intel 2011/2066 cooler base mounting
brackets.
• 清潔 表面CPU
CPU表面擠適量散熱膏,塗抹均勻
Clean the CPU surface.
Apply and spread the thermal paste to CPU evenly.
• 移除散熱器底座保護
Remove cooler base protective film.
• 安裝散熱風扇
Install cooling fan using included fan clips.
• 連接散熱風扇 街頭到主機板 孔位4Pin PWM CPU Fan
• 安裝AMD散熱器底座固定支架
Install the AMD cooler base mounting brackets.
Make sure the PWM cable included is connect to
PWM socket
Make sure the Top Cover LED cable is connect to
main fan Top Cover LED socket
Connect cooling Fan 4Pin PWM connector to motherboard
CPU Fan socket.
• 安裝散熱器對準背板螺桿後放置在
CPU
• 使用彈簧螺絲完成散熱器及主機板的安裝
Align the AMD cooler base mounting brackets to backplate
screw bolts, then place the air cooler on the CPU carefully.
Using spring screw nuts to complete the air cooler and
motherboard installation.
安裝散熱器對準背板螺桿後放置在 上CPU
使用彈簧螺絲完成散熱器及主機板的安裝
Align the Intel
2011/2066
cooler base mounting brackets to
backplate screw bolts, then place the air cooler on the
CPU
carefully.
Using spring screw pillar to complete the air cooler and
motherboard installation.
Intel LGA 2011/2066
ARGB Connector Instruction & Mini ARGB LED Controller Instruction
ARGB連接使用說明 & 迷你ARGB控制器使用說明
Mini ARGB LED Controller Mode
Please connect the 3pin ARGB
connector to Mini ARGB LED
Controller, plug and play.
● 迷你 控制器模式ARGB
連接頭插入迷你控3pin ARGB
制器並運作
ARGB Mother SYNC Mode
Please connect the 3pin ARGB
connector to ARGB Motherboard,
plug and auto switch to ARGB
Motherboard SYNC mode.
主機板同步模式ARGB
插入至主機板3pin ARGB
ARGB 針腳並自動同步模式
LED Speed:
Click to Switch LED Speed.
單擊切換 LED 速度
LED Display Mode :
Click MODE+ or MODE-
Button to Switch Different
LED Display
單擊MODE+或MODE-
換LED模式
LED ON/OFF:
Click and Hold More Than
3 Seconds for LED On or Off.
長按三秒關或關LED
SATA(To PSU)
連接電源供應器SATA


Product specificaties

Merk: Xigmatek
Categorie: Niet gecategoriseerd
Model: Windpower Pro

Heb je hulp nodig?

Als je hulp nodig hebt met Xigmatek Windpower Pro stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Xigmatek

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd