Wilbur Curtis PCGT3 Handleiding

Wilbur Curtis Koffiezetapparaat PCGT3

Lees hieronder de 📖 handleiding in het Nederlandse voor Wilbur Curtis PCGT3 (9 pagina's) in de categorie Koffiezetapparaat. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/9

3. Plug the power cord into an electrical outlet rated at 20A.

4. Turn on power at the toggle switch behind the unit. The lights (display window and row of but-

tons) on the front door will activate and the heating tank will start to ll.

5. Water in the heating tank will require about one hour to reach operating temperature (factory

setting of 190°F). At this time the LCD will display “READY TO DISPENSE”.

6. Remove and ll the canisters with powdered cappuccino product.

Your Curtis G3 System is Factory Pre-Set and Ready to Go, Right from the Box.

Following are the Factory Settings for your Primo Cappuccino Beverage System:

• Tank Temperature = 190°F

• Flavor Controls= Set at 60%

• Dispensing Mode Set for Manual Dispensing

Generally there will never be a reason to change your G3 programming. However, should you

need to make slight adjustments to meet your dispensing needs, programming instructions are

provided later in this manual.

System Requirements:

• Water Source 20 – 90 PSI (Minimum Flow Rate of 1 GPM)

• Electrical: See electrical schematic on page 7.

Models Included

• PCGT3 STANDARD

• PCGT3 PRESET DISPENSE

• PCGT3 ICED CAPPUCCINO

CAUTION: DO NOT

connect the unit to hot

water. The inlet valve is

not rated for hot water.

CAUTION: Follow this

setup procedure before

attempting to use this

unit. Failure to follow these instruc-

tions can result in injury and/or void

of warranty.

CAUTION: Equipment

must be installed to

comply with applicable

federal, state, and local plumbing/

electrical codes having jurisdiction.

Important Safeguards/Symbols

This appliance is designed for commercial use. Any servicing other than cleaning and routine main-

tenance should be performed by an authorized Wilbur Curtis Company service technician.

• DO NOT immerse the unit in water or any other liquid

• To reduce the risk of re or electric shock, DO NOT open service panels. There are no user

serviceable parts inside.

• Keep hands and other items away from hot areas of the unit during operation.

• Never clean with scouring powders or harsh chemicals.

W C C ., i .ilbur urtis o nC

Service Manual – PCGT3

Symbols

WARNINGS – To help avoid personal injury

Important Notes/Cautions – from the factory

Sanitation Requirements

NSF International requires the following water connection:

1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine

can be moved for cleaning underneath.

2. This equipment is to be installed with adequate backow protection to comply with applicable

federal, state and local codes..

3. Water pipe connections and xtures directly connected to a potable water supply shall be sized,

installed and maintained in accordance with federal, state, and local codes.

SETUP STEPS

1. The unit should be level (left to right - front to back), on a secure surface.

2. Connect the water line to the water inlet tting on the rear of the unit. Water volume going to the

machine should be consistent. Use tubing sized sufciently to provide a minimum ow rate of

one gallon per minute.

NOTE: A water ltration system must be used to help maintain trouble-free operation. Air must be purged from the

cartridge prior to connection to equipment. In areas with extremely hard water, we highly recommend the use of

a Curtis approved water lter. For our full line of lters, please log on to www.wilburcurtis.com.

ISO 9001:2008 REGISTERED

WILBUR CURTIS CO. INC.

6913 Acco Street,

Montebello, CA 90640-5403

For the latest information go to

www.wilburcurtis.com

Tel: 800/421-6150

Fax: 323/837-2410 FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO WWW.WILBURCURTIS.COM

COLD OR HOT?

STOP/WASH

DISPENSE

WASH

SANITIZE

RINSE

IMPORTANT - Do not remove pillars to take off mounting plate.

I. EVERY 3 - 4 HOURS OR MORE OFTEN IF NECESSARY

A. Make sure power is ON.

B. Place a container under the dispense spout to catch the rinse water.

C. Locate the WASH button on the front control panel.

D. Rinse each avor by pressing and holding the WASH button, while at the same

time pressing one of the PUSH dispensing buttons on the control panel.

E. Continue holding the WASH button until the water running from the spout runs clear.

II. DAILY

A. Switch OFF the unit at the power toggle switch, located behind the unit.

B. Wipe all exterior surfaces with a damp cloth, removing any spills, residue or dust

from the unit.

C. Remove both the drip drawer and louvered screen; then wash out its contents. For

hard to clean deposits, use a mild, nonabrasive detergent. Rinse with water.

D. Wipe and clean the dispensing area with a mild detergent cleaner.

III. WEEKLY OR MORE OFTEN IF NECESSARY

A. Clean the parts from the whipper assembly.

1. Remove the dispensing nozzle from the whipper chamber. Clean the inside using a narrow brush.

2. Remove the upper mixing cup. Pull cup forward, twist to the left and lift it to separate the upper

mixing cup from the lower mixing cup.

3. To remove the lower mixing cup, pull mixing cup up and forward to free it from the

hot water inlet tting.

4. Remove the whipper chamber. Take hold of the whipper chamber. Turn it clock

wise to free it from the mounting plate.

5. Pull the whipper propeller from the motor shaft.

6. Wash, Rinse and Sanitize using a 3-sink method. Air dry all parts.

7. Re-assemble cleaned parts onto the machine.

CAUTION - Do not use cleansers, liquid bleach, powders or any other substance containing chlorine. These products

promote corrosion and will pit the stainless steel. THE USE OF THESE PRODUCTS WILL VOID YOUR WARRANTY.

Cleaning the Curtis Primo Cappuccino GT Beverage Dispenser

Operation Instructions

1. Choose a avor. Place your cup under the spout beneath the desired avor.

Note: When using Iced Cappuccino machine, ll your cup with ice before dispensing product.

2. Push and hold the dispensing button for this avor.

3. Release the button when the cup is ¾ full.

FILL CANISTERS DAILY

1. Open the front door to access the product canisters.

2. The canisters must be removed from the unit for lling. Turn the powder delivery elbows

clockwise, pointing upward. Pull all of the canisters from the canister tray.

3. Rell the canisters. The small canisters hold ve pounds of product. Larger canisters hold 10

pounds each. See Conguration of Canisters on page 6.

3. Reposition the canisters on the canister tray. Properly mate the gear socket with the gear on

the motor shaft when aligning canisters. Turn the elbows clockwise, pointing downward.

c. Clean the area behind the mounting plate.

d. Clean the water inlet tting.

e. Lubricate the center seal of the mounting plate before reinstalling.

IMPORTANT - When replacing the propeller, make sure it is properly aligned and seated on the motor

shaft. The propeller has an embossed ‘D’ to properly align it on the motor shaft.

Failure to properly seat the propeller will cause it to fuse with the whipper chamber. This condition will not

be covered under warranty.

6. Clean the mounting plate.

a. Clean the shaft with a cloth and mild detergent before removing mounting plate.

b. Twist the mounting plate clockwise and pull it from the motor shaft.

Steps to Programming

Your Curtis Generation 3 cappuccino

dispenser is Factory Pre‑Set for Optimum

Performance. Programming for all models is

identical except where noted.

Entering the Programing Menus

Press and hold STOP/WASH for

about ten [10] seconds. Display will

read Program Menus,(See Illustra-

tion).

Manual Dispense (Factory Set to Manual Dispense)

Press  or > to go to Manual Dispense Select.

Press  to go to Manual Dispense Select Station.

Choose the station and press, the display will read Saving Complete! To select another station for manual dispense,

press  to go to Manual Dispense Select Station or press > to continue to the next menu.

Dispense By Time (Factory Setting OFF)

The next screen is Dispense By Time < Select >. Press to select a station. Select the station and the screen will 

read To Begin Press Push. Press desired dispense button. Hot water will start to dispense and screen will display

To Finish Press Push. When Push is pressed, time will be saved and you will exit back to Dispense by Time screen.

Continue with additional selections or press > to continue to the next menu.

Temperature (Factory set at 190°F – Cold Cappuccino Units Set at 96ºF)

Press  and screen will show Tank Temperature. Temperature is programmable from 80°F to 204°F in 2-degree incre-

ments. Press < or > to go up or down in degrees. Select desired temperature and then to set. Press > to continue 

to the next menu.

Powder % Ratio (Factory set at 60%)

Press - and the screen will display Powder % Ratio Select Station. Press desired station. Powder ratio is program

mable from 0% (Hot Water) to 100%, in 5% increments. Press < or > to increase or decrease ratio and then press

 to set. Press > to continue to the next menu.

Valves should not be eld adjusted to change product strength.

Product strength adjustments should be done through programming on the front panel only.

Service Call (Factory Set to 1-800-000-0000 x0000)

Press to display number and press change number or > to move places and EX to exit when complete This  

number will be displayed during a Heating system SENSOR ERROR or a WATER ERROR. Press > to continue to the

next menu.

Banner Name (Factory Set to Curtis)

Press to display letters, press to change letters or > to move places and EX to exit when complete. 

This feature allows up to 14 letters to be programmed for company name or regional name. Programming all blanks

disables Banner Name. Press > to continue to the next menu.

Model Select

Press to select, < or > to select desired model (PC-3, 4, 5) . Press to set and exit program mode. 

Exit

Press to select, exits program mode and returns unit to operation. 

Product specificaties

Merk:	Wilbur Curtis
Categorie:	Koffiezetapparaat
Model:	PCGT3

Heb je hulp nodig?

Als je hulp nodig hebt met Wilbur Curtis PCGT3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Koffiezetapparaat Wilbur Curtis

Wilbur Curtis NIB1 Handleiding

14 Juni 2023

Wilbur Curtis G4TP 2T Handleiding

11 Juni 2023

Wilbur Curtis G4 ThermoPro Handleiding

10 Juni 2023

Wilbur Curtis G4TP 5T Handleiding

10 Juni 2023

Wilbur Curtis G4TP 3T Handleiding

3 Juni 2023

Wilbur Curtis PCGT3 Handleiding

2 Juni 2023

Wilbur Curtis NIB2 Handleiding

1 Juni 2023

Wilbur Curtis CAFE PC3 Handleiding

28 Mei 2023

Wilbur Curtis TC-7HK Handleiding

26 Mei 2023

Wilbur Curtis G4GEMS10 Handleiding

21 Mei 2023

Handleiding Koffiezetapparaat

Nieuwste handleidingen voor Koffiezetapparaat

Electrolux Explore 7 E7CM1-6GB Handleiding

21 December 2024

Electrolux Explore 7 E7CM1-4GB Handleiding

21 December 2024

Electrolux Explore 7 E7CM1-2GB Handleiding

21 December 2024

Gaggia Anima R18760 Handleiding

21 December 2024

Gaggia Babila RI9700 Handleiding

21 December 2024

Oster BVSTDC3394 Handleiding

20 December 2024

Oster BVSTDCSC4404 Handleiding

20 December 2024

Oster BVSTEM3300 Handleiding

20 December 2024

Oster BVSTDCSC4403 Handleiding

20 December 2024

Gaggia Cadorna Plus RI9601 Handleiding

18 December 2024