Westinghouse 6107335 Handleiding

Westinghouse Lamp 6107335

Lees hieronder de 📖 handleiding in het Nederlandse voor Westinghouse 6107335 (1 pagina's) in de categorie Lamp. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Installation and Safety Instructions
Warning: Electrical shock can result in serious injury.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed. Contact a qualified electrician. Read
all instructions before beginning. Proper wiring is essential for safe operation of this fixture. When cutting or drilling into walls or
ceilings, do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not
install fixture. Return to place of purchase.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service
agent or a similar qualified person in order to avoid a hazard.
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
For indoor use only.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty
and service. For questions and comments, please visit www.westinghouselighting.eu/contact-us and www.
westinghouselighting.de/contact-us
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see
figure 1).
MOUNTING AND WIRING INSTRUCTIONS
NOTE: Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this
fixture.
1. Thread mounting screws (A) into mounting bar (B) (see fig. 1) approximately 1/4 inch.
2. Place mounting bar (B) flush against ceiling at desired mounting location. Using outside mounting bar holes
as a guide, mark where pilot holes are to be drilled.
3. Inset two plastic anchors (D) into the pilot holes (for drywall ceiling).
4. Align outside mounting bar holes with plastic anchors (D) (If applicable). Secure mounting bar (B) into place
using wood screws (E).
5. Make an electrical connection by loosening the terminal screws on the terminal block (F) and inserting the
live, neutral and ground terminals.
6. Tighten terminal screws. Make sure there are no stray wires.
7. Raise canopy (H) to ceiling allowing mounting screws (A) to protrude through key slots (G) in canopy (H)
(see fig. 1).
8. Rotate canopy (H) clockwise until mounting screws (A) lock into narrow portion of key slots (G). Secure into
place with mounting screws (A).
9. Raise the shade (C) up allowing the protrusions to engage the slot of the canopy (H). And twist the shade (C)
to lock into place.
10. Turn power back on at circuit box.
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of
fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lacquer which gives
maximum protection against the weather. However, in time the brightness of the brass will tarnish, giving way to an
authentic old-world brass finish. To keep your solid brass fixture looking new for years to come, regularly apply a good
quality, non-abrasive car wax to all metal surfaces, giving the fixture an extra protective covering.
Meaning of crossed-out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact you local
government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get
into the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal
at least free of charge.
Appliance specifications - TECHNICAL CHARACTERISTICS
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF
are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All rights reserved.
Made in China
W-607
052818
*NOT SUPPLIED
FIGURE 1.
C
G
H
D
F
E
B
A
Rated voltage 220-240V~
Rated frequency 50Hz
Rated wattage Integrated LED Max. 20W
Protection class CLASS I
IP number IP20
Ambient temperature 40
o
C


Product specificaties

Merk: Westinghouse
Categorie: Lamp
Model: 6107335

Heb je hulp nodig?

Als je hulp nodig hebt met Westinghouse 6107335 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Lamp Westinghouse

Handleiding Lamp

Nieuwste handleidingen voor Lamp