Warm Audio RingerBringer Handleiding

Warm Audio Niet gecategoriseerd RingerBringer

Lees hieronder de 📖 handleiding in het Nederlandse voor Warm Audio RingerBringer (34 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/34

RINGERBRINGER

• ENGLISH (PG 1) • FRANÇAIS (PG 7) • ESPAÑOL (PG 13) • DEUTSCH (PG 20)

• (PG 26) • 简体中文日本語 (PG 29)

THANK YOU!

Thank you for purchasing the Warm Audio RingerBringer. We feel this product delivers an accurate recreation in terms

of sound, function, and vibe of a legendary pedal. We don’t cut corners when it comes to what goes into our products,

and RingerBringer is no exception.

Bryce Young

President

Warm Audio

Austin, Texas USA

Before we begin, please take the time to visit www.warmaudio.com to register your product. To ensure you receive proper

and uninterrupted warranty support for your product, please register your unit within 14 days from purchase.

NOW LETS GET STARTED!

INTRODUCTION

The Warm Audio RingerBringer accurately recreates the ultimate all-analog ring modulation effect used for experi-

mental tones. With LFO, MOD, FREQUENCY & RATE controls, you can generate layered frequencies and harmonics,

explore a wide range of sonic possibilities for guitar & beyond, and design your own sounds from the ground up.

Sporting premium components including hand-selected op-amps and transistors, the RingerBringer delivers true-to-

spec performance of the boutique original.

PEDAL LAYOUT & CONTROLS

1. MODULATION CONTROLS

• Mix: The MIX control on RingerBringer allows crossfade the dry and wet (modulated) signals. Turning

the knob clockwise will increase the percentage of “wet” effect tone vs. dry signal, adding wobble and

pitch shift depending on other pedal settings. 100% counterclockwise yields zero modulation and 100%

clockwise yields a fully wet signal.

• Frequency: The Frequency control on RingerBringer determines the frequency of the carrier oscillator,

affecting the pitch and harmonic content of the ring-modulated output. As you increase the frequency

(clockwise), you will begin to hear the distance between the harmonic content as shifted pitch. The lower

the setting, the more it sounds like tremolo, at higher frequency settings, more harmonic dissonance and

pitch shifting will occur.

• LO/HI Switch: The LO/HI switch sets the range of the frequency settings for the carrier oscillator inside

RingerBringer. The “LO” setting range is [0.6 Hz to 80 Hz] and the “HI” setting range is [30 Hz to 4 kHz]

2. LFO CONTROLS

A NOTE ON THE LFO-SIDE OF THE WA-RB

LFO, or Low Frequency Oscillator, is typically used to generate effects like vibrato and tremolo. RingerBringer

features a dual-waveform, voltage-controlled LFO that modulates the carrier oscillator frequency.

• Amount: The AMOUNT knob on RingerBringer sets the degree to which the LFO waveform modulates

the frequency of the carrier oscillator. When turned counterclockwise, there is no frequency modulation

from the LFO. Rotating the knob fully clockwise,however, results in a frequency modulation spanning three

octaves for the carrier oscillator.

• Rate: The RATE knob on RingerBringer controls the speed at which the LFO oscillates. This knob covers a

frequency range of 0.1 Hz - to 25 Hz, with 1 Hz being equal to one cycle per 10-second interval.

• Sine/Square Switch: The SINE/SQUARE switch on RingerBringer allows you to choose between the

square waveform and the sine-like waveform generated by the LFO. The square wave will produce ﬂut-

tering/trembling effects, while the sine waveform creates vibrato and more gradual pitch-altering tones.

3. DRIVE CONTROL

The DRIVE knob on RingerBringer ﬁne-tunes the input gain, allowing precise adjustment for a variety of in-

struments or line-level signal sources. Turning the knob clockwise will INCREASE the amount of gain applied.

Weaker signals will need more turning of the knob while stronger signals can afford less use of the knob. The

DRIVE control is always on, even when RingerBringer is bypassed, so setting this control acts as a unity gain for

your signal while RingerBringer is in the chain. You can also push the drive knob into harmonic overdrive and

even distortion as well.

Product specificaties

Merk:	Warm Audio
Categorie:	Niet gecategoriseerd
Model:	RingerBringer

Heb je hulp nodig?

Als je hulp nodig hebt met Warm Audio RingerBringer stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Warm Audio

Warm Audio RingerBringer Handleiding

12 Maart 2024

Warm Audio WarmBender Handleiding

12 Maart 2024

Warm Audio WA-1B Handleiding

7 December 2023

Warm Audio ODD Box V1 Handleiding

26 Juli 2023

Warm Audio WA-14 Handleiding

6 Februari 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

True UNITE Touchscreen Console Handleiding

23 December 2024

Alpine TME-M780EM Handleiding

23 December 2024

ARNOLD Lichttechnik MCU 400 D Handleiding

23 December 2024

HK Audio TB-45NQ Handleiding

23 December 2024

HK Audio TB-45N Handleiding

23 December 2024

D-Link DFE-680TX Handleiding

23 December 2024

D-Link DGE-550T Handleiding

23 December 2024

D-Link DGE-560SX Handleiding

23 December 2024

D-Link DGE-510T Handleiding

23 December 2024

Mercusys MS116GS Handleiding

23 December 2024