Vimar ELVOX 69MD Handleiding

Vimar Niet gecategoriseerd ELVOX 69MD

Lees hieronder de 📖 handleiding in het Nederlandse voor Vimar ELVOX 69MD (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Cod. S6I.69M.C0E RL.01 6/2012

Art. 69MC - 69MD

INSTALLATION AND OPERATION MANUAL

ELVOX TWO-WIRE AUDIO / VIDEO INTERFACES

Product is according to EC Directive 2004/108/CE, 2006/95/CE and following norms.

2/8

69MC - 69MD

2. SOFTWARE CONFIGURATIONS (ONLY WITH ART. 69MD)

The configurations can be made only via the programming module

Art. 950C connected to the serial socket inside art. 69MD (see Fig.

2). Alternatively it is possible to use the interfaces Art. 692I or 692I/U

and the PC software SaveProg (Art.69CD). The configurable para-

meters are:

1. GENERAL INFORMATION

Articles 69MC and 69MD are interfaces on a 4 module DIN enclo-

sure that enable converting (extracting) the audio and video signal

from an ELVOX TWO-WIRE bus line. Art. 69MC always extracts the

audio and video signal, when available in the two-wire bus, regar-

dless of the flat called. Article 69MD extracts the audio and video si-

gnal when a valid signal is available in the two-wire bus of one or

more flats programmed in article 69MD. For the programming it is

necessary to use art. 950C or PC. By default art. 69MD has all 200

flats active for extracting the audio/video signal Every time art.

69MC and 69MD are activated to extract the video signal they close

a normally open contact.

R R M

Terminal block CN2

V M A

CN1

Elvox Two-

Wire bus

termination

Art. 69MC

TERMINAL BLOCK CN7

MARK DESCRIPTION

+ Power supply 20V

- Ground power supply

Fig. 1

The power is supplied with art. 6582 to keep the circuit isolated. The

jumper CN1 with 3 positions A,B,C is the terminator of the bus for

the video signal and is used in the same way as all the other ELVOX

TWO-WIRE products: in the case of a feedthrough bus keep CN1 on

A, otherwise terminate on B or C according to the best position for

the video output. R91 regulates the output audio level. It is already

set in the factory to supply 0.5Vpp and must not be changed unless

absolutely necessary. R52 regulates the output video level. It is al-

ready set in the factory to supply 1 Vpp and must not be changed

unless absolutely necessary.

The terminal block CN2 has the following signals and controls:

TERMINAL BLOCK CN2

MARK DESCRIPTION

RContact of a normally open relay . It closes

when the video signal is good. Peak voltage

and current at the contacts 24V 0.5A

MVideo earth

VVideo output

MAudio earth

AAudio output

R R M V M A

CN3

Connector to

p r o g r a m -

ming module

Art. 950C

+ -

B1 B2

Art. 69MD

Terminal CN7

Supply

Fig. 2

PARAMETER DEFAULT NEXT

ITEM

UNDER

ITEM

Language Italian

(local language)

Video activation

delay

1 s

Video/Audio ac-

tivation

All on

204 x or

+ -

B1 B2 Terminal CN7

Supply

Terminal block

CN3 Bus Line

CN1

Two Wire

Elvox bus

termination

R52

Video level

R52

Video level

R91

Audio level

R91

Audio level

Terminal block

CN3 Bus Line

Terminal block CN2

3/8

69MC - 69MD

The programmer keypad layout is as follows:

The button has no function because the programmer is po-

wered via the bus. For the same reason the auto-shutdown fun-

ction is not available. The programmer keys and enable

selection of the following item from the main menu:

During the phase of waiting for the response from the interface,

the display shows:

After a few seconds the programmer display will show the type

and release of the software for the interface:

When it disappears the first item on the programming menu will

appear. The programming procedure ends either due to timeout

or by pressing the button while you are in any of the external

menus listed below.

On\Off

2.1. MESSAGE LANGUAGE

The programs can be run in Italian (local language, default) or in

English. Other languages will be available for the respective mar-

kets. To change language, press for Italian or for En-

glish.

To cancel press . To confirm, press . Acceptance of the

command, as in all cases, is shown on the first line of the display:

The display now changes to:

Use the key to move to the previous item in the programming

menu.

2.2. VIDEO ACTIVATION DELAY

Pressing the button takes you to the next item where you

can select the time elapsing between the incoming message that

indicates there is a video signal in the bus and the demodulated

output that is supplied:

PUSH-BUTTON ACTIVATION EXAMPLE

No activation

Only video

Audio and video

On\Off

This is because when the video activation command passes

through the bus, the video signal might not be present and sta-

bilized in amplitude. In addition, also the internal circuit needs a

certain time for stabilizing. Supplying such a video signal to cer-

tain kinds of monitor can make them unstable in the sense that

from that moment until they are switched off they will no longer

show a correct video signal. The time is regulated from 0 to 5 se-

conds in steps of 0.1 s. To change the time, simply key in the new

value. In this case, press and for 2 seconds:

To cancel press . To confirm, press . Acceptance of the

command, as in all cases, is shown on the first line of the display:

Use the key to move to the previous item in the programming

menu.

2.3. AUDIO / VIDEO ACTIVATION

Pressing the button takes you to the next item where you

can change, flat by flat, whether to supply only the video output

or both. By default it is all on:

To select the device to modify, use keys and . From po-

sition 1, press to move to the next item in the programming

menu. Alternatively, enter the device number required directly:

Now press :

In the event of discrepancies, the first line of the display shows

the error:

Use the key to skip all intermediate phases and go to the

previous item in the programming menu. To change the activation

setting, press:

Now the buttons , and and they have this meaning:

Product specificaties

Merk:	Vimar
Categorie:	Niet gecategoriseerd
Model:	ELVOX 69MD

Heb je hulp nodig?

Als je hulp nodig hebt met Vimar ELVOX 69MD stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Vimar

Vimar ELVOX 0931/240 Handleiding

16 November 2024

Vimar ELVOX 6680/V04 Handleiding

16 November 2024

Vimar 19457.TR.B Handleiding

16 November 2024

Vimar 20457.TR.N Handleiding

16 November 2024

Vimar 20457.TR.B Handleiding

16 November 2024

Vimar ELVOX K42917 Handleiding

11 Juli 2024

Vimar ELVOX EBRA.3L Handleiding

9 Juli 2023

Vimar ELVOX 6621 Handleiding

9 Juli 2023

Vimar 08376 Handleiding

9 Juli 2023

Vimar 14380 Handleiding

7 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024