Verbos Electronics Control Voltage Processor Handleiding

Verbos Electronics Niet gecategoriseerd Control Voltage Processor

Lees hieronder de đź“– handleiding in het Nederlandse voor Verbos Electronics Control Voltage Processor (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Control Voltage Processor
Congratulations on obtaining your new Verbos Electronics Control Voltage
Processor. This Euro-Rack format module allows mixing, scaling, inverting,
crossfading, slewing, compressing, offsetting and modulating of not only control
voltages but any signals inside your modular synthesizer.
The Top Section
The top section of the module is a Slew Rate Processor with independent control
of the positive and negative moving voltages. In addition to the panel control for
each of these, there is a c.v. input for each with a reversing attenuator to scale
the control amount. A Trigger input and manual gate button will send the output
up to 8 volts at the Positive rate and back down at the Negative rate. The Shape
can be continuously swept from linear to curved, as expected from classic por-
tamento circuits. The curves are “true RC” in the sense that they are not created
using feedback, therefore they always start fast and end slow throughout the
voltage range from -11 volts to +11 volts. A Gate Out goes high for negative volt-
ages and low for positive ones and allows looping if it is patched to the trigger
in. Bounce, a feature unique to this module, allows control voltage to overshoot
its destination by an amount set by the control, at the rate of the Positive control.
This gives the effect of letting go of a tape machine’s reel and hearing the pitch
wobble.
The Lower Sections
The lower two sections are identical voltage processors. Inputs 1 and 2 have
reversing attenuators, allowing inverting, scaling, addition and subtraction. Inputs
3 and 4 are a voltage controlled crossfader, which can also be used as a VCA
that opens or closes with voltage or even a 4 quadrant modulator. The Offset
control will add or subtract a xed voltage to the mix. The voltage range of these
processors is more than +/-11 volts.
18HP • 240g • +12v 85mA • -12v 83mA
c.v. output
Shape control Negative control
Bounce
control
Voltage Processor
Offset control
Gate output
Select c.v. input
(crossfades between inputs 3 & 4)
Positive control
input reversing
attenuators
Select control
Slew Rate Processor
Trigger input
c.v. output
c.v. inputs
c.v. input
Trigger button


Product specificaties

Merk: Verbos Electronics
Categorie: Niet gecategoriseerd
Model: Control Voltage Processor

Heb je hulp nodig?

Als je hulp nodig hebt met Verbos Electronics Control Voltage Processor stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Verbos Electronics

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Electrolux

Electrolux STA9 Handleiding

23 November 2024
Electrolux

Electrolux UMP3 Handleiding

23 November 2024
Bosch

Bosch HEZ8TK36UC Handleiding

23 November 2024
Bosch

Bosch HEZ8ZZ36UC Handleiding

23 November 2024
Bosch

Bosch HDZIT301 Handleiding

23 November 2024
Bosch

Bosch HEZBS301 Handleiding

23 November 2024
LG

LG LX-330 Handleiding

23 November 2024
Bosch

Bosch KSZ2AVU00 Handleiding

22 November 2024