Ventus W263 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Ventus W263 (4 pagina's) in de categorie Weerstation. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
W263-0 & W235-0
Features:
- Soil moisture
- Soil temperature
- Air temperature on the remote sensor
- Indoor air temperature
- Watering alert display & alarm setting
- Weather Forecast
- Digital clock with daily alarm
Battery installation:
Main unit W203GP:
- Open the battery door and insert 4 pieces of AA batteries according to the polarity shown
Remote sensor W235G0
- For first time use, pull out the plastic strip from the battery door
- For battery replacement, remove the battery door and replace with a new CR2450 battery
Setting up the sensor:
1) Hold the [Channel/Search] button on the main unit W203GP to search for the sensor
2) Select the channel number on the remote sensor by rotating to the desired channel number
3) Hold the [Tx] button inside the battery compartment of the plant sensor W235G0 to transmit
signal
4) Once RF synchronization is completed, the corresponding channel data will be displayed on
the main unit
To setup for another remote sensor, select different channel number on the sensor and follow
above procedure.
Soil moisture display:
Moisture Levels:
Wet 4 bars
Slightly Wet: 3 bars
Slightly Dry: 2 bars
Dry: 1 bar
Buttons & Operation
Key Operation:
[CH (channel) ]:
- Select channel from channel 1,2,3,4,5 & auto-scroll
- Hold to search for remote sensor
[Watering alarm on/off]
- Press to enable / disable the watering alarm
The “AL ((.))” icon appears when it is enabled
Watering alarm beeping pattern:
- Beeps once every 1 minute
- It does not beep from 9pm to 9am
[Up / C/F]
- Press to toggle between degree C & F
- Press to increase digit value in setting mode
[Down]
- Press to increase digit value in setting mode
[Max Min Memory]
- Press to show maximum, minimum & current air, indoor & outdoor temperature readings
- Hold 3 seconds to clear the memory
[Alarm (Bell)]
- Press to show alarm time. When alarm time display, press to on/off alarm.
- When alarm time display, press and hold 3 seconds to enter setting alarm time
[Clock]
- Press and hold 3 seconds to enter setting clock
[Snooze]
- When alarming, press the button to enter snooze.
CLOCK SETTING
Hold “CLOCK“ button for 3 seconds to enter clock set. Using “ + , - “ to adjust and “ CLOCK ” to
confirm, the following values can be set in sequence: Hr > Min > 12/ 24 >Existing Weather >
confirm & exit (if not confirmed, auto exit & save after 1 minutes)
ALARM SETTING
Press to view Alarm Time for 10 seconds.
Hold “ALARM“ for 3 seconds, Hr will flash, press “ +, - “ to enter the desired value and press
“ALARM“ to confirm. Minute will flash, press “ +, - “ to enter the desired value and press
“ALARM“ to confirm. Alarm mode Zz will flash, press “ +, -“ to select Zz snooze alarm, (bell) daily
alarm or Alarm off (no icon). Zz snooze alarm will be enabled when user enter into alarm setting
each time.
SNOOZE
Press SNOOZE to trigger snooze alarm. To stop alarm for one day, press ALARM key but not
“SNOOZE” key.
Setting up the sensor:
1) Hold the [Channel/Search] button on the main unit W263 to search for the sensor
2) Select the channel number on the remote sensor by rotating to the desired channel number
3) Hold the [Tx] button inside the battery compartment of the plant sensor W235 to transmit
signal
4) Once RF synchronization is completed, the corresponding channel data will be displayed on
the main unit
To setup for another remote sensor, select different channel number on the sensor and follow
above procedure.
Soil moisture display:
Moisture Levels:
Wet 4 bars
Slightly Wet: 3 bars
Slightly Dry: 2 bars
Dry: 1 bar
WEATHER FORECAST
The unit predicts weather condition of the next 12 – 24 hours based on the change of atmospheric
pressure. The coverage area is around 30 – 50 km. The weather forecast is based on
atmospheric pressure change and is about 70-80% correct. As weather conditions cannot be
100% correctly forecasted, we cannot be responsible for any loss caused by an incorrect forecast.
Weather Forecast:
SUNNY SLIGHTLY CLOUDY CLOUDY RAINY STORMY
Pressure Tendency:
Rising Steady Falling
LOW BATTERY INDICATION
Low battery indication is available for the home unit itself and all of the 3 remote channels.
Replace the batteries and follow the setup procedure as mentioned in this instruction manual.
Specification:
Operating temp: 0C to 50C (main unit & remote sensor)
Channel number: Maximum 5 channels
Soil moisture level: 1 (dry) to 4 (wet)
RF frequency: 433MHz
Power: AA x 4 pieces (main unit)
CR2450 x 1 piece (remote sensor W235G0)
Reference
Different plants require different level of soil moisture. Some plant prefer drier soil conditions and
some like to be kept moist.
Plant
Suggested watering level
setting Plant
Suggested watering level
setting
African Violet 2 or above Ivy, English 2 or above
Aglaonema 2 or above Ivy, Grape 2 or above
Aphelandra 3 or above Ivy, Swedish 2 or above
Aralia 2 or above Jade Plant 1 or above
Ardisia 2 or above Kalancho 1 or above
Azalea 2 or above Landscape Plants 1 or above
Baby's Tears 3 Lawns 1 or above
Begonia 2 or above Maranta 3
Bromeliad 1 or above Ming Aralia 2 or above
Cactus 1 or above Nepthytis 2 or above
Caladium 3 Norfolk Island Pine 1 or above
Chinese Evergreen 2 or above
Palms - Areca, Bamboo,
Fishtail, Kentia, Lady,
Ponytail Pador 3
Christmas Cactus 1 or above Peperomia 1 or above
Coffee 2 or above Philodendron 2 or above
Coleus 2 or above Pilea 2 or above
Crassula 1 or above Podocarpus 3
Croton 2 or above Pothos 2 or above
Cryptanthus 1 or above Prayer Plant 2 or above
Dieffenbachia 1 or above Rubber Plant 1 or above


Product specificaties

Merk: Ventus
Categorie: Weerstation
Model: W263

Heb je hulp nodig?

Als je hulp nodig hebt met Ventus W263 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Weerstation Ventus

Handleiding Weerstation

Nieuwste handleidingen voor Weerstation