Velleman K8400 Handleiding

Velleman 3D Printer K8400

Lees hieronder de 📖 handleiding in het Nederlandse voor Velleman K8400 (12 pagina's) in de categorie 3D Printer. Deze handleiding was nuttig voor 120 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

English

............................................

........................................................................................

............................................

.............................................

.........................................................................................

Nederlands

............................................

................................................................................

....................................

................................................................................

Français

............................................

......................................................................................

..........................................

......................................................................................

Deutsch

...........................................

.......................................................................................

............................................

.......................................................................................

Espanõl

............................................

.......................................................................................

...........................................

.......................................................................................

- 2 -

VELLEMAN-KIT

3D Printer kit

Order code: K8400

Manufactured by:

VELLEMAN NV.

Legen Heirweg, 33

9890 Gavere

Belgium

Important safety instructions

The K8400 is a DIY 3D printer kit, it contains all the bits and pieces to construct your own 3D printer but does not contain additional

protection. As it is a kit and not a finished product, compliance with the CE regulations depends on the build-quality; also the following

notes must be taken into account.

CE conformity information:

The included power supply meets all the applicable European requirements and bears the CE-mark. It is protected against overload

and short circuit and nothing needs to be modified. The working voltage of the 3D printer is 15Vdc (extra low voltage) and therefore

it’s outside the scope of the Low voltage directive.

Always unplug before maintenance or modification.

Electrical safety:

Electromagnetic radiation (EMC):

Conductive EMC towards the public distribution network is not an issue as this is related to the power supply. Radiated EMC

depends substantially on the build quality, it might be required to add shielding but this cannot be predicted. A built K8400 should

comply with EN50081 normation

The 3D printer contains a lot of moving parts, but the force of the stepper motors is too low to cause serious injuries. Neverthe-

less it is recommended to provide additional protection against mechanical risks. The easiest way to make your 3D printer “accident

proof” is to put it inside a protective enclosure which completely covers the 3D printer – with or without an access door and fume

extraction. (numerous designs can be found on the internet)

To make it extra safe a switch which interrupts the power supply of the printer when the enclosure or door is opened can be added.

It is also advisable to install an external emergency stop switch, which also cuts off the power supply.

Providing a dequate protection is the responsibility of the assembler.

Always cut power before maintenance or modification.

Mechanical safety and protection:

- 3 -

The

The 3D

3D printer

printer

printer is

is not

not

not intended

intended

intended for

for

for use

use

use by

by persons

persons

persons (including

(including

(including children)

children)

children) with

with

with reduced

reduced

reduced physical,

physical,

physical, or

or mental

mental

mental capabilities,

capabilities,

capabilities, or

or lack

lack

lack of

of experience

experience

The 3D printer is not intended for use by persons (including children) with reduced physical, or mental capabilities, or lack of experience

and

and knowledge,

knowledge,

knowledge, unless

unless

unless they

they

they have

have

have been

been

been given

given

given supervision

supervision

supervision or

or instruction

instruction

instruction concerning

concerning

concerning the

the

the use

use

use of

of the

the

the appliance

appliance

appliance by

by a

a person

person

person responsible

responsible

and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible

for their safety

Children should be supervised to ensure that they do not play with the appliance.

The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide.

The information in this document was obtained from sources which we believe are reliable.

However, the information is provided without any warranty, express or implied, regarding its correctness.

The conditions or methods used for assembling, handing, storage, use or disposal of the device are beyond our control and may be

beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, injuries,

damage, or expense arising out of or in any way connected with the assembly, handling, storage, use or disposal of the product.

There is a potential risk of burns as the Printer head (extruder) can reach up to 270°C. The use of common sense should be sufficient to

prevent burns, but in some environments it is highly recommended to provide additional protection. (see § Mechanical safety and protection)

Always let the 3D printer cool down for 60 min. before maintenance or modification.

Risk of burns:

This printer is designed for use with PLA and ABS filament (MSDS for the Velleman filament is available).

PLA: is a safe and non-toxic material, there are no known health safety risks when used in 3D printers.

ABS: when printing with ABS there is a distinctive ‘burned plastic’ smell. This is quite normal but it may also cause headaches, res-

piratory- and eye irritation with sensitive people (although it is not toxic)

Only use the printer in a well-ventilated area, if printing with ABS it is advisable to add a fume hood (with active carbon

filtering for ductless extraction). Fume extraction is mandatory for use in offices, classrooms and alike.

Never burn printer filament, toxic gasses and vapors will be generated if exposed to fire.

Health:

General safety information:

Getting started

Illustrated assembly instructions:

www.vertex3dprinter.eu/manual

3D-printer info, specifications,...

www.vertex3dprinter.eu

Support

(Downloads, Product support, Community)

www.vertex3dprinter.eu/support

Product specificaties

Merk:	Velleman
Categorie:	3D Printer
Model:	K8400
Kleur van het product:	Doorschijnend
Ingebouwd display:	Ja
Gewicht:	10000 g
Breedte:	360 mm
Diepte:	380 mm
Hoogte:	395 mm
USB-poort:	Ja
Ethernet LAN:	Nee
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	SD
Kijkglas:	Ja
USB-versie:	2.0
Display technologie:	LCD
Meegeleverde software:	Modified Open Source Marlin 3D Printer
Temperatuur bij opslag:	-10 - 40 °C
Printtechnologie:	Fused Filament Fabrication (FFF)
AC-ingangsspanning:	100-240 V
AC-ingangsfrequentie:	50 - 60 Hz
Stroomverbruik (typisch):	150 W
Breedte mondstuk:	0.35 mm
Printmateriaal:	ABS, Polylactic acid (PLA)
Ondersteunde filamentdikte:	1.75 mm
Maximaal afdrukformaat:	- mm
Laagdikte (min):	0.05 mm
Laagdikte (max):	0.2 mm
Aantal printkoppen:	2
Maximale printplatformtemperatuur:	270 °C