VAX Rapide Total Floors V-029Q Handleiding

VAX Stoomreiniger Rapide Total Floors V-029Q

Lees hieronder de 📖 handleiding in het Nederlandse voor VAX Rapide Total Floors V-029Q (5 pagina's) in de categorie Stoomreiniger. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
Vax Careline:
0870 6061248
Instruction Manual
Please read carefully before using
the washer. Always fully extend
the mains cable before use.
www.vax.co.uk
Vax Model Number V-029
Vax Model Number V-029Q
1. Brushbar switch on/off
2. Mains power switch
on/off
3. Clean water tank cap
(rear of tank)
4. Clean/Dirty water tank
handle
5. Clean/Dirty water tank
latch release
6. Nozzle setting indicator
7. Nozzle base
8. Squeegee
9. Hard floor nozzle
10. Brushbar (underside of
carpet washer)
11. Locking ring
12. Brushbar reset push
13. Solution trigger
14. Carpet nozzle
15. Carry handle
16. Power cord
17. Carpet nozzle storage
18. Quick cord release
19. Nozzle setting pedal
20. Non-marking wheels
21. Handle release pedal
1. Diagram
Parts Overview
22. Vax AAA Carpet Cleaner
NOTE: Always test an inconspicuous area for colour fastness - rub a
small area with a dilute mixture of Vax carpet cleaner on a soft white cloth.
23. Vax Multi Hard Floor Cleaner (CAUTION: TO PREVENT DAMAGE TO
WOOD FLOORS, FOLLOW THE MANUFACTURERS CLEANING
RECOMMENDATIONS. BEFORE USING ON SEALED WOOD FLOOR,
ENSURE THAT SURFACE IS NOT WORN, BARE OR HAS SEPARATED
JOINTS. DO NOT USE IF ANY OF THESE CONDITIONS EXIST.) Do not
use on unsealed wood/laminate floors.
8
10
6
13
14
16
18
9
17
20 20
19
21
15
7
11
12 2
3
4
5
1
2
2. Safety Information
FOR HOUSEHOLD USE ONLY.
When using the cleaner, basic safety precautions should
always be observed, including the following.
1. Do not leave the cleaner unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not to be used as a toy. Close supervision is
necessary when used by or near children or the
infirm.
4. Use only as described in this manual.
5. Do not use with a damaged cord or plug. 'If the
supply cord and/or plug is damaged, they must be
replaced by the manufacturer, a Vax Service Agent
or similarly qualified persons in order to avoid hazard.
6. Do not pull or carry by the cord, use the cord as a
handle, allow the cord to come into contact with hot
or sharp surfaces or close a door on the cord.
7. Do not unplug by pulling on the cord.
8. Do not handle the plug or carpet washer with wet
hands.
9. Do not put any objects into openings or operate
with openings blocked, keep them free of anything
that may reduce airflow.
10. Keep hair, loose clothing, fingers, and all parts of
the body away from openings and moving parts.
11. Do not use the cleaner on any glowing, burning or
smoking particles.
12. Do not use without the Clean/Dirty water tank in place.
13. Turn off all controls before unplugging.
14. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they
may be present.
15. Keep the cleaner on the floor.
16. Do not use an extension cord.
17. Do not attempt to remove blockages with sharp
objects as they may cause damage.
18. Store indoors put away after use to prevent
tripping accidents.
19. Using improper voltage may result in damage
to the motor and possible injury to the user.
The correct voltage is listed on the rating label.
20. This cleaner is intended for household use only.
21. A hazard may occur if the carpet washer runs over
the power supply cord.
Safety Information/Use & Function
Fig.1/1
Fig.1/4
Fig.1/3
Fig.1/2
3. Use & Function
Assembling the cleaner
Fig.3/1
3
NOTE: Your cleaner contains a thermal protective
device to shut off the motor to avoid overheating.
If this happens, turn the unit off and unplug the
cleaner. Inspect the nozzle inlet for blockage. Empty
the Dirty Water Tank and clean the filter. After
approximately 30 minutes, the motor will have cooled
and the vacuum will be ready to use.
NOTE: The cleaner must remain unplugged during
the 30 minute cooling period.
22
23
Remove the product from the packaging and gently
push the handle assembly on to the machine body.
Secure with four screws supplied, in the positions
shown. Do not over tighten the screws.
Use & Function
4
Use & Function
Cleaning floors
5
The recommended sequence of cleaning is as follows:
Operating
sequence
Brushbar
Switch
Nozzle
setting
Trigger
switch
Dry
Vacuum OFF Released OFF
Wet
Cleaning ON Depressed ON
Drying OFF Released ON
IMPORTANT: TO PREVENT DAMAGE TO WOOD
FLOORS, FOLLOW THE MANUFACTURERS
CLEANING RECOMMENDATIONS. BEFORE USING
ON SEALED WOOD FLOOR, ENSURE THAT
SURFACE IS NOT WORN, BARE OR HAS
SEPARATED JOINTS. DO NOT USE IN WET
CLEANING MODE WITH THE BRUSHBAR ON.
DO NOT USE IF ANY OF THESE CONDITIONS EXIST.
DO NOT USE ON UNSEALED WOOD/LAMINATE
FLOORS.
Fill
Fig.3/3 Fig.3/4
1. Push down on Clean/Dirty Water Tank latch. Pull
tank up and out. Fig 3/3.
Fig.3/5 Fig.3/6
2. Remove cap from Clean Water Tank. Fig 3/4.
3. Pour 2 capfuls of Vax AAA Carpet Cleaner or Vax
Multi Floor Hard Floor Cleaner concentrate into
solution bottle cap. Fig 3/5 and 3/6.
IMPORTANT: DO NOT USE PINE, SOLVENT, OR
WAX BASED CONCENTRATES IN CLEANER.
4. Fill remainder of Clean Water Tank with warm
[max 40C] water up to the max fill line. Replace
cap on tank. Fig 3/7.
Fig.3/7 Fig.3/8
5. Replace Clean/Dirty Water Tank into main body of
cleaner. Snap latch to secure. (Fig.3/8).
6. With dry hands, plug cord into properly grounded
electrical outlet. (Fig.3/9).
7. Step on Handle Release pedal to put into cleaning
position. (Fig.3/10).
Fig.3/9 Fig.3/10
8. Turn cleaner on by switching the power on/off
switch [located on the side of the cleaner]. Fig. 3/11.
9. Step on the Nozzle Setting pedal to switch to
select the cleaning option. Fig. 3/12.
ON
OFF
Fig.3/9 Fig.3/10
Emptying and cleaning the dirty water
tank
IMPORTANT: TO REDUCE THE RISK OF INJURY
FROM MOVING PARTS - UNPLUG BEFORE
SERVICING.
Your cleaner is equipped with a shut off valve within
your Dirty Water Tank. Empty the Dirty Water Tank
when the wet and/or dry debris reaches the “Debris
Max Fill” line on the outside of the Clean/Dirty Water
Tank or the float rises, shutting off air flow through
the nozzle.
NOTE: You will hear a noticeable change in the
pitch of the cleaner. This indicates a need to empty
the Dirty Water Tank. The outer tank (Clean Water
Tank) contains the cleaning solution and water mix
while the inner tank (Dirty Water Tank) collects dry
and wet debris.
1. Disconnect cleaner from electrical outlet. Place
cleaner handle in upright and locked position. Fig
3/9.
2. Push down on Clean/Dirty Water Tank latch while
grabbing handle and pulling tank up and out from
main body of cleaner. Fig 3/10
Fig.3/9 Fig.3/10
3. Grasp tab and pull up to remove filter assembly
out of tank. (Fig 3/11) Empty contents into sink.
4. Return the filter back into Clean/Dirty Water Tank.
To ensure a proper fit, make sure arrow on the filter
is aligned with the arrow on Clean Water Tank Cap.
Fig 3/12.
5. Replace Clean/Dirty Water Tank into main body of
cleaner and snap Clean/Dirty Water Tank latch
into place. Fig. 3/13.
Fig.3/11
Fig.3/12
A
L
I
G
N
F
I
L
T
E
R
F
R
O
N
T
Fig.3/13
Fig.3/2


Product specificaties

Merk: VAX
Categorie: Stoomreiniger
Model: Rapide Total Floors V-029Q

Heb je hulp nodig?

Als je hulp nodig hebt met VAX Rapide Total Floors V-029Q stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Stoomreiniger VAX

Handleiding Stoomreiniger

Nieuwste handleidingen voor Stoomreiniger