Vantec UGT-CR961 Handleiding

Vantec Geheugenkaartlezer UGT-CR961

Lees hieronder de 📖 handleiding in het Nederlandse voor Vantec UGT-CR961 (4 pagina's) in de categorie Geheugenkaartlezer. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Prepare your computer case for installation.

2. Locate an available 3.5” or 5.25” drive bay where you would like

to install the device.

5.25” Drive Bay

3.5” Drive Bay

*Using Optional 3.5” to 5.25” Front Bay Converter Kit (HDA-525P) to install into a 5.25” Front Bay

Slide the front panel device into your case until the front panel

is flush with the front of your case.

1b. Secure the 5.25” front panel device to your computer case with

the provided screws.

2b. Proceed to connect the front panel device to your system’s

motherboard or expansion card.

3b.

Connect to

System 20 pin

USB 3.0 Header

Connect to

System Audio

port Header

Connect to

System SATA

port Header

Proceed to connect the front panel device to your system’s

motherboard or expansion card.

3a.

Secure the 3.5” front panel device to your computer case with

the provided screws.

2a.

Slide the front panel device into your case until the front panel

is flush with the front of your case.

1a.

3.5” Front Panel Installation

Connect to

System 20 pin

USB 3.0 Header

Connect to

System Audio

port Header

Connect to

System SATA

port Header

Installation Guide Guía de instalación Guide d'installation Installationsanleitung

Guida all’installazione 取り付けガイド安裝指南安装指南

Verify the package contents.

3.5” Front Panel Device Installation Guide

Installation Screws

Secure with the screws provided by the 3.5” to 5.25” front panel

converter bracket.

Slide in the 3.5” front panel device into the front bay converter kit

until the front panel is flush.

Prepare the 3.5” to 5.25” front panel converter kit.

If you would like to mount your 3.5” device into your 5.25” drive bay, you may do so by using Vantec’s HDA-525P 3.5“ to 5.25” bay converters. Follow the steps below to convert your device form factor to 5.25”.

Converting Your 3.5” Front Panel Device to 5.25” Form Factor

Make sure all connection are connected well and place the cover

back on to your case.

5. Drivers will be automatically detected and installed. Your device

will be ready for use.

v1.01

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden.

Printed in China

Printed on Recycled Paper.

Diagram shown is the USB 3.0 20-Pin found on supported motherboards or expansion cards. Please refer to your motherboard

manufacturer’s documentation for the location of these ports.

Connecting Your Front Panel Device

SATA

SATA header on system

Note: Missing pin

and notch on the

connector matches

notch on the head

USB 3.0(20-pin*) header on system

Audio header

on system

Note: Missing pin

Connect to

System 20 pin

USB 3.0 Header

Connect to

System Audio

port Header

Connect to

System SATA

port Header

Supports all standard memory cards.

Product specificaties

Merk:	Vantec
Categorie:	Geheugenkaartlezer
Model:	UGT-CR961
Kleur van het product:	Zwart
Breedte:	135 mm
Diepte:	101 mm
Hoogte:	25 mm
Materiaal behuizing:	Plastic, Steel
LED-indicatoren:	Ja
Compatibele geheugenkaarten:	CF, Memory Stick (MS), MicroSD (TransFlash), MMC, MS Duo, MS Micro (M2), MS PRO, MS PRO Duo, MS Pro-HG, MSXC, SD, SDHC, SDXC, xD
Plug and play:	Ja
Aansluitingen:	Audio I/O
Intern:	Ja
Power LED:	Ja
Soort aansluiting:	SATA
Overdrachtssnelheid:	6144 Mbit/s
Aantal USB 3.2 Gen 1 (3.1 Gen 1)-poorten:	1
Aantal eSATA-poorten:	1
Ondersteundende drive bays:	3.5 "