Vantec NST-520S3-BK Handleiding

Vantec Niet gecategoriseerd NST-520S3-BK

Lees hieronder de 📖 handleiding in het Nederlandse voor Vantec NST-520S3-BK (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden.

Printed in China

Printed on Recycled Paper.

Installation Guide

For NST-510S3-BK (9.5mm only). For NST-520S3-BK (12.7mm) see back page.

USB 3.0 Slim SATA

Optical Drive Enclosure

The Operating System will detect USB Mass storage device

connected and load the necessary drivers built into the

Operating System. No other drivers are needed.

8. Once the drivers are installed the Optical drive is ready for use.

Carefully slide out the optical drive tray.

Slide the Tray with the secured optical drive into the

Aluminum housing and secure with two screws.

Slide the Optical drive on the Tray until the Slim SATA interface on

the Optical drive dock completely with the Tray Slim SATA interface.

If the Front Plate of your Optical Drive is using a Protruding or

Curve Front Plate, please use the provided Front Plate to replace

it. Follow the picture showing the hook to remove and replace.

Flat Front Plate

Side View

Protruding or

Curve Front Plate

1) Eject the Optical Tray by inserting a

paper clip into the eject hole on the

front of the Optical drive.

2) Note the location and direction of

the hooks on the provided Flat Front

Plate, unhook each hook slowly.

3) Replace it with the provided Flat

Front Plate back onto your Optical

drive. Note the location of the 4 hooks.

Secure the Optical Drive to the Tray using the provided

small screws on both sides.

Connect the USB cable to the Optical unit and your system USB port.

The Optical unit is bus powered. It will draw power from the USB port.

USB 3.0 Cable USB 3.0 Port

Optional USB

Power Connection

*Optional USB Power Connection:

If your Optical Drive need more power than 1 USB 3.0

port can provide. please use the additional USB power

connection to your system, If you are not sure connect both.

Verify the package contents.

USB 3.0 Cable

Front Plate

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden.

Printed in China

Printed on Recycled Paper.

Installation Guide

For NST-520S3-BK (12.7mm only). For NST-510S3-BK (9.5mm) see back page.

USB 3.0 Slim SATA

Optical Drive Enclosure

If the Front Plate of your Optical Drive is using a Protruding or Curve

Front Plate, please use the provided Front Plate oto replace it. Follow

the picture showing the hook to remove and replace.

Flat Front Plate

Side View

Protruding or

Curve Front Plate

1) Eject the Optical Tray by inserting a

paper clip into the eject hole on the

front of the Optical drive.

2) Note the location and direction of

the hooks on the provided Flat Front

Plate, unhook each hook slowly.

3) Replace it with the provided Flat

Front Plate back onto your Optical

drive. Note the location of the 4 hooks.

Connect the USB cable to the Optical unit and your system

USB port. The Optical unit is bus powered. It will draw

power from the USB port.

USB 3.0 Cable USB 3.0 Port

Optional USB

Power Connection

*Optional USB Power Connection:

If your Optical Drive need more power than 1 USB 3.0

port can provide. please use the additional USB power

connection to your system, If you are not sure connect both.

Verify the package contents.

USB 3.0 Cable

Front Plate

The Operating System will detect USB Mass storage device

connected and load the necessary drives built into the

Operating System. No other drives are needed. Once the

drives are installed the Optical drive is ready for use.

Slide the Optical drive on the Tray until the Slim SATA interface on the

Optical drive dock completely wuth the Tray Slim SATA interface.

5. Secure the Optical Drive to the Tray using the provided

small screws on both sides.

Remove the two screws holding the back plate and peel

away the back plate held by a latch shown.

Slide the tray into aluminum housing and secure the back plate with

two provided screws.

Slide out the Tray for mounting the Optical Drive.

Product specificaties

Merk:	Vantec
Categorie:	Niet gecategoriseerd
Model:	NST-520S3-BK
Kleur van het product:	Zwart
Breedte:	136 mm
Diepte:	151 mm
Hoogte:	20 mm
Materiaal behuizing:	Aluminium, Plastic
Meegeleverde kabels:	USB
Snelstartgids:	Ja
USB-versie:	3.2 Gen 1 (3.1 Gen 1)
USB-aansluiting:	Ja
Maat:	- "
Geïntegreerde USB-kabel:	Nee
Optical drive interface:	SATA