Valcom VP-6124-UPS Handleiding

Valcom Batterij-oplader VP-6124-UPS

Lees hieronder de 📖 handleiding in het Nederlandse voor Valcom VP-6124-UPS (3 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

VSP VP- - -6124 UPS

Issue 3

1947271

VP- -6124 UPS

ADD ON OPTION FOR THE VP- - -6124/VP 6124 E

POWER SUPPLY

INTRODUCTION

The VP- -6124 UPS is an optional unit that allows the

VP- - -6124/VP 6124 E to supply power during a power

outage.

The VP- - - -6124 UPS is comprised of a VP 6124 UPS

(Charger) and a VBB-1424 (Battery Enclosure). The

VP- - -6124 UPS connects to the VP 6124 Power Supply

(To receive power to charge the batteries).

Listed below are specifications and recommendations

for power sources as well as precautionary

instructions.

UPS Float Standby Charging

Charging Voltage: 27.6 Volts (13.8 Volts per battery)

Current Limit: 900mA charging

100mA at 27 Volts final charge

Fusing: 1 Amp auto-reset polyswitch

6 Amps accidental reverse battery polyswitch

Time Required to Recharge Battery

7AH Battery: 14 hours

Length of Time Battery Will Provide

Power

• With four 7AH 12V batteries for 14AH total

3 Amps load draw: 3 hours run time

6 Amps full load: 1.5 hours run time

Use of batteries greater than 7AH is not

recommended since 90% of all power outages are less

than an hour in length and the time to evacuate a

building is less than an hour.

NOTE: To insure trouble- -free UPS back up

operation, five years batteries must be replaced five

years from the date of manufacturing.

DIMENSIONS/WEIGHT

• 10.30"H x 3.50"W x 2.25"D

• (26.16cm H x 8.89cm W x 5.72cm D)

2.90 lbs. (1.32 kg)

INSTALLATION

The VP- -6124 UPS (Charger) is designed for wall

mounting only. Screw the mounting plate to the wall

near the VP- - -6124/VP 6124 E and position the

VP- -6124 UPS onto the mounting plate.

Attach the UPS unit securely to the bracket lip using

the 6- -32 x 3/8" long Phillips head self tapping screw

supplied. Place the VBB-1424 on the floor within six

feet of the unit.

CONNECTIONS

• Disconnect AC power from the power supply.

• Remove plug button from the VP- - -6124/VP 6124 E.

• Remove wire access cover from the

VP- - -6124/VP 6124 E.

• Using the cable designated by the tag labeled

Valcom P/N WA-784 with four positions

connector and attached to VP- -6124 UPS

(Charger), place the Molex connector through the

hole on the power supply and connect the

charger to the Molex input connector on the

VP-6124 Power Supply.

• Snap strain relief into place.

• Replace wire access cover on the

VP- - -6124/VP 6124 E.

• Remove cover from Battery Backup.

• Push cable labeled Valcom P/N WA-783 with two

positions connector through the hole on the

battery enclosure and snap strain relief into

place.

• Attach connector from VP- -6124 UPS to battery

box.

• Replace access cover.

• Plug power cord from VP- - -6124/VP 6124 E into AC

outlet.

• Turn ON circuit breaker on Battery Backup.

OPERATION

When a power failure occurs, the charger beeps to

alert personnel that the supply is operating on the

batteries and there is 1.5 hour run time available at 6

Amps full load. Pressing the white button will mute

the beeping.

There are three (3) LEDs located on the charger.

When the charger is connected to the

VP- - -6124/VP 6124 E power supply, the green LED

illuminates signifying the power supply and charger

are on line and the batteries are charging.

If the red LED illuminates, this denotes that the

batteries have dropped below 20 Volts and the UPS

goes into low voltage shutdown to protect the

batteries from damage. This disconnects the load.

The red LED will turn off and batteries reconnect

when power returns and the batteries are charged

above 25 Volts.

Pressing the battery test button illuminates the yellow

LED if the battery is above 24Volts (Signifies a good

battery). The charger will charge the batteries to 27.6

Volts in a 14 hour period assuming completely

discharged batteries.

Batteries must be replaced every five years.

CAUTION: To reduce the risk of fire or injury

to persons, read and follow these instructions.

1. Supplied with four (4) Union Type MX12070

batteries. Use only Union Type MX12070

batteries.

2. Do not dispose of the batteries in a fire. The cell

may explode. Check with local codes for possible

special disposal instructions.

3. Do not open or mutilate the batteries. Released

electrolyte is corrosive and may cause damage to

the eyes or skin. It may be toxic if swallowed.

4. Exercise care in handling batteries in order not to

short the battery with conducting materials such

as rings, bracelets, and keys. The battery or

conductor may overheat and cause burns.

5. Do not attempt to recharge the batteries provided

with this or identified for use with this product.

The batteries may leak corrosive electrolyte or

explode.

6. Do not attempt to rejuvenate the batteries

provided with or identified for use with this

product by heating them. Sudden release of the

battery electrolyte may occur causing burns or

irritation to eyes or skin.

7. When replacing batteries, all batteries should be

replaced at the same time. Mixing fresh and

discharged batteries could increase internal cell

pressure and rupture the discharged batteries

(Applies to products employing more than one

separately replaceable primary battery).

8. When inserting batteries into this product, the

proper polarity or direction must be observed.

Reverse insertion of batteries can cause charging,

and that may result in leakage or explosion

(Applies to products employing more than one

separately replaceable primary battery).

9. Remove the batteries from this product if the

product will not be used for a long period of time

(several months or more) since during this time the

battery could leak in the product.

10. Discard "dead" batteries as soon as possible since

"dead" batteries are more likely to leak in a

product.

11. Do not store this product, or the batteries provided

with or identified for use with this product, in

high-temperature areas. Batteries that are stored

in a freezer or refrigerator for the purpose of

extending shelf life should be protected from

condensation during storage and defrosting.

Batteries should be stabilized at room temperature

prior to use after cold storage.

NOTE: The batteries are excluded from the

WARRANTY.

TECHNICAL ASSISTANCE

When trouble is reported, verify that the unit is

properly connected and there are no broken

connections leading to this unit. Assistance in

troubleshooting is available from the factory. When

calling, you should have a VOM and a telephone test

set available and be calling from the job site. Call

(540) 563-2000 and ask for Technical Support, or call

(540) 767- -1555 for Valcom 24 hour Faxback System or

visit our website at http://www.valcom.com.

Valcom equipment is not field repairable. Valcom, Inc. maintains service facilities in Roanoke, VA. Should repairs be

necessary, attach a tag to the unit clearly stating company name, address, phone number, contact person, and the

nature of the problem. Send the unit to:

Repair and Return Dept.

Valcom, Inc.

5614 Hollins Road

Roanoke, VA 24019-5056

- - -+ + +

VP-6124/VP-6124-E

Power Supply

24V Outputs

To other page

units or amplified

speaker assemblies.

A Ground

A Battery

B Ground

B Battery

Typical Page

Control Unit

Local

GND

Strap

VP-6124-UPS

VBB-1424

WA-784 WA-783

CONNECTIONS TO THE VP-6124/VP-6124-E

Breaker

(Face plates are shown for each unit)

VALCOM LIMITED WARRANTY

Valcom, Inc. warrants its products to be free from defects in materials and workmanship under conditions of normal use and service

for a period of one year from the date of shipment. The obligation under this warranty shall be limited to the replacement, repair or

refund of any such defective device within the warranty period, provided that:

1. inspection by Valcom, Inc. indicates the validity of the claim,

2. the defect is not the result of damage, misuse, or negligence after the original shipment,

3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (A service

charge plus parts and labor will be applied to units defaced or physically damaged),

4. freight charges for the return of products to Valcom are prepaid,

5. all units ‘out of warranty’ are subject to a service charge. The service charge will cover minor repairs (Major repairs will be

subject to additional charges for parts and labor).

This warranty is in lieu of and excludes all other warranties, expressed or implied, and in no event shall Valcom, Inc. be liable

for any anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the

purchase, operation, or use of the product.

This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the

carrier should be notified immediately. Claims for such damage should be filed with the carrier involved in accordance with the

F.O.B. point.

Headquarters: In Canada

Valcom, Inc. CMX Corporation

5614 Hollins Road 35 Van Kirk Drive #11 and 12

Roanoke, VA 24019-5056 Brampton, Ontario L7A1A5

Phone: (540) 563-2000 Phone: (905) 456-1072

FAX: (540) 362-9800 FAX: (905) 456-2269

Product specificaties

Merk:	Valcom
Categorie:	Batterij-oplader
Model:	VP-6124-UPS
Kleur van het product:	Grijs
Gewicht:	2250 g
Breedte:	150.368 mm
Diepte:	63.5 mm
Hoogte:	261.62 mm
Soort:	Batterijlader voor binnengebruik
Materiaal behuizing:	Metaal
Ondersteund aantal accu's/batterijen:	1
Certificering:	UL, CSA, CE
Ingangsspanning:	120 V
Temperatuur bij opslag:	10 - 90 °C
Frequentie:	50/60 Hz
Spanning:	24 V
Compatibiliteit:	VP-6124, VBB-1424
Compatibele batterij technologiën:	Sealed Lead Acid (VRLA)
Afmetingen (B x D x H):	150.368 x 63.5 x 261.62 mm
Stroomverbruik (typisch):	165 W
Bedrijfstemperatuur (T-T):	0 - 40 °C
Batterijen inbegrepen:	Nee