Valcom VIP-9890-CB Handleiding

Valcom Intercomsysteem VIP-9890-CB

Lees hieronder de 📖 handleiding in het Nederlandse voor Valcom VIP-9890-CB (4 pagina's) in de categorie Intercomsysteem. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

1 947704

ISSUE 3

VIP-9890-CB

Vandal Resistant IP DoorPhone/Intercom

INTRODUCTION

The VIP-9890-CB IP Talkback Doorphone /

Intercom allows communication to Valcom

FXS units (VIP-811, -812, -814) and SIP-enabled

telephone systems via an IP network. The

VIP-9890-CB combines a rugged; weather-

resistant talkback paging horn with a vandal-

resistant enclosure, which is ideally suited for

high-noise, exposed environments.

SPECIFICATIONS

Access Methods

 PBX, FXO Port w/VIP-811

 POTS telephone set w/VIP-811

 Valcom M Cast Page Group

 SIP – enabled telephone system

Features

 RJ-45 for network connection

 1 Form C contact

 LED Status Indicator

 Network activity LEDs

 Power over Ethernet (PoE) 802.3af

compatible

 Door Opening Contact Provided

Dimensions/Weight

Intercom Unit:

 10.0” H x 12.5" W x 4" D

(25.4cm H x 31.75cm W x 10.2cm D)

 Weight: 10.75lbs. (4.1 kg)

Network Interface:

 2.0” H x 4.63" W x 9.13" D

(5.1cm H x 11.8cm W x 23.2cm D)

 Weight: 0.80lbs. (0.36 kg)

Nominal Specifications

Input Impedance: 600 Ohms

Input Level: -10dBm

Output Impedance: 600 Ohms

Output Level: -10dBm nominal

Relay Current: 1AMP @ 24VDC

Nominal Power Requirements

Via 802.3af (PoE) Ethernet Switch Class 3

Environment

VIP-9890-CB Network Interface

Temperature: 0 to +40° C

Humidity: 0 to 85% non-precipitating

VIP-9890-CB Intercom Unit:

Suitable for indoor or outdoor installation

Packing List

Qty Item

1 VIP-9890-CB Network Interface

1 VIP-9890-CB Intercom Unit

1 VSP Document

4 Tamper Hardware (Intercom unit only)

1 VIP172-RLY Relay Block

4 Wood Screws

2 947704

CAUTION: To reduce the risk of electric shock,

Do not remove cover.

No user serviceable parts inside.

Refer servicing to qualified service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that dangerous

voltage constituting a risk of electric

shock is present within this unit.

This symbol indicates that there are

important operating and maintenance

instructions in the literature accompanying

this unit.

Precautionary Designations

FCC Information

This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses and can radiate

radio frequency energy and if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area may cause

harmful interference in which case the user

will be required to correct the interference at

his own expense.

INSTALLATION

Operation:

The VIP-9890-CB provides intercom access via

network connection to customer telephone

system or stand alone telephone set. Interface to

customer telephone system can be via SIP

registration to a Voice over IP (VoIP) telephone

system, or FXO port (when used with a VIP-811).

Pressing the call button on the intercom unit

initiates a call to a user-specified telephone

number, and the call assurance LED behind the

intercom unit face plate begins to flash. When

the call is answered, a hands-free

communications path is established to the

intercom unit, and the call assurance LED behind

the face plate remains lit. The form C relay

included with the VIP-9890-CB may be activated

by pressing the # key on the answering

telephone, with the relay typically being used to

activate door entry equipment.

Mounting

For enhanced protection against static

electrical discharge, it is recommended the

intercom unit shipped with the VIP-9890-CB

be installed onto a grounded electrical box, If

surface mounted, ground box to local ground.

The VIP-9890-CB Intercom unit is designed for

double gang FD electrical box mounting and must

be within 300 meters of the VIP-9890-CB

Network Interface. See NEMA OS 3-2002

sec.1.2.3.5 for FD box speciﬁcations.

The VIP-9890-CB Network Interface is designed

for wall mounting and must be within 100 meters

of the network switch. Using the wood screws

provided, secure the VIP-9890-CB Network

Interface to the wall. Remove the Intercom unit

from the packing container. Using a Phillips

screwdriver, remove the two screws securing the

front grille to the enclosure. Pre-drilled 13/64”

mounting holes in the back of the enclosure are

designed to fit a single gang, double gang or

octagon outlet box. If not attaching to an outlet

box, use the enclosure as a template. Hold the

enclosure in the desired position on the wall and

mark the location of mounting holes. Depending

on wall construction type, prepare the mounting

hole locations on the wall to securely attach the

enclosure.

Wiring may be inserted through the large hole in

the back of the enclosure, or through the

knockout hole in the top of the enclosure. Insert

wiring for signal connections and relay

connections (if used) through desired hole. Use

mounting hardware (not included) appropriate for

the wall type to securely mount the enclosure to

the wall.

After making signal connections, align the

grille/speaker assembly with the enclosure.

Install the four supplied tamper-resistant screws

through the grille into the enclosure. Use a 1/8”

security hex bit (not included) to tighten the

screws securely.

Power Connections

The only method of powering a VIP-9890-CB

Network Interface is via a Power over Ethernet

(PoE) switch or power injector meeting the

802.3af specification.

Make all required signal connections before

connecting to Ethernet switch or power injector

meeting the 802.3af specification.

3 947704

Network Connection

The VIP-9890-CB Network Interface has one

RJ-45 NETWORK connector and one RJ-45

DOOR connector.

Use a standard Ethernet patch cable to connect

the NETWORK connector of the VIP-9890-CB

Network Interface to an Ethernet switch.

Signal Connections

Use standard Category 5 UTP cable to connect

the VIP-9890-CB Network Interface to the

Intercom unit. Connect the RJ-45 jack (labeled

Door) on the Network Interface to the RJ-45 jack

on the back of the Intercom unit speaker

assembly using a standard Ethernet patch cable.

Door Relay Connections

Access to the form C relay is provided via a three

pin screw terminal block on the VIP-9890-CB

Intercom unit. The common contact is the middle

terminal. The Normally Open contact is on the

side closest to the RJ-45 connector, the Normally

Closed contact is on the side furthest from the

RJ-45 connector. Please refer to Figure 1.

For higher security, the included VIP172L-RLY

connection block can be used. Please refer the

Quick Start Installation guide packaged with the

VIP172-RLY for installation details.

Aux Input

Aux input on the VIP-9890-CB Network Interface

accepts line level audio such as background

music and broadcasts it through the Intercom unit

speaker. When the call button is pressed, the aux

input is muted and remains muted until the call is

terminated.

Status Indicator Lights

The VIP-9890-CB Intercom unit is equipped with

a status indicator LED. LED flashes when the call

button is pressed and steady when the call is

connected.

The VIP-9890-CB Network Interface has 3 status

indication lights on the side panel:

STATUS: Flashes during normal operation, and

solid during system startup..

LINK: Indicates 100 Mbit Ethernet connection

when illuminated. No activity indicates 10 Mbit

connection.

ACT: Indicator flashes to indicate network

activity.

Setup

Information specific to your application will need

to be programmed into the VIP-9890-CB using a

computer. The PC used for programming should

be connected to the same subnet as the

VIP-9890-CB.

Setup will be done using the IP Solutions Setup

Tool. Download the latest version of the free IP

Solutions Setup Tool from the Valcom web site at

www.valcom.com/vipsetuptool.

TECHNICAL ASSISTANCE

Assistance in troubleshooting is available from

the factory. Call (540) 563-2000 and press 1 for

Technical Support or via email at

support@valcom.com.

When requesting assistance, you should include

all available information. Information and trouble-

shooting procedures are available on the Valcom

website at www.valcom.com.

Valcom equipment is not field repairable.

Valcom, Inc. maintains service facilities in

Roanoke, VA. Should repairs be necessary,

attach a tag to the unit clearly stating your

company name, address, phone number, contact

person and the nature of the problem. Send the

unit to:

Valcom, Inc.

Repair & Return Dept.

5614 Hollins Road

Roanoke, Va. 24019-5056

Product specificaties

Merk:	Valcom
Categorie:	Intercomsysteem
Model:	VIP-9890-CB
Kleur van het product:	Metallic, Yellow
Materiaal behuizing:	Metaal
Luidspreker:	Ja
Video call:	Nee
Ingebouwde camera:	Nee
Aantal knoppen:	1
Afmetingen (B x D x H):	317.5 x 102 x 254 mm
Hoeveelheid modules (max):	1 module(s)
IP connectable:	Ja