Valcom Trunk Port VIP-821 Handleiding

Valcom Netwerkkaart/adapter Trunk Port VIP-821

Lees hieronder de 📖 handleiding in het Nederlandse voor Valcom Trunk Port VIP-821 (3 pagina's) in de categorie Netwerkkaart/adapter. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

1 947970

ISSUE 4

VIP-821

NETWORKED TRUNK PORT

INTRODUCTION

The VIP-821 Networked Trunk Port allows most

loop start terminal devices to be connected to a

managed IP-based LAN/WAN.

SIP connectivity allows the VIP-821 to act as a

gateway device between a SIP telephone system

and the other Valcom paging systems, such as

the MultiPath.

SPECIFICATIONS

Access Methods

 PBX, FXS Port

 SIP

Features

 RJ-45 for network connection

 1 RJ-11 FX0

 1 RJ-11 telephone failover connection

 Front panel activity LED

 Network activity LEDs

 2.5mm jack for DC

 802.3af compliant

Dimensions/Weight

 1.38 H x 6.13" W x 5.25" D

(3.50cm H x 15.6cm W x 13.33cm D)

 Weight: 1.25 lbs. (0.57 kg)

Nominal Specifications

Input Impedance: 600 Ohms

Input Level: -10dBm

Output Impedance: 600 Ohms

Output Level: - 10dBm nominal

Nominal Power Requirements

Via rear panel barrel connector:

Voltage: 24VDC

Current: 325mA

Via 802.3af PoE Ethernet Switch:

802.3af: Class 3

Environment

Temperature: 0 to +40° C

Humidity: 0 to 85% non-precipitating

Packing List

Qty Item

1 VIP-821

1 VSP Document

2 Mounting Brackets W/Hardware

4 Rubber Pads

INSTALLATION

NOTE: The telephone system referred to in

this manual is the customer premise

equipment such as an electronic key system,

a PBX or a dedicated single line telephone

sets. The VIP-821 is not intended for direct or

indirect connection to the public telephone

network. When used with a customer premise

telephone system such as a key system or

PBX system, these units are interfaced to the

FXS or single line station port, which is a fully

protected interface device. Also, the host

system must be configured to disallow central

office trunk conferencing in order to prevent

indirect connection to the public network.

2 947970

CAUTION: To reduce the risk of electric shock,

Do not remove cover.

No user serviceable parts inside.

Refer servicing to qualified service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that dangerous

voltage constituting a risk of electric

shock is present within this unit.

This symbol indicates that there are

important operating and maintenance

instructions in the literature accompanying

this unit.

Precautionary Designations

FCC Information

This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses and can radiate

radio frequency energy and if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area may cause

harmful interference in which case the user

will be required to correct the interference at

his own expense.

Mounting

The VIP-821 is designed for wall or table

mounting.

Wall: Using the bracket and screws provided,

secure the VIP-821 to the wall.

Table: Provided with the VIP-821 are four rubber

pads. Peel the pads from their carrier backing

and place at the four corners of the bottom of the

unit.

Power Connections

The preferred method of powering a VIP-821 is

via a power over Ethernet switch meeting the

802.3af specification.

If the rear panel barrel connector is used for

power, the preferred power supply is a Valcom

VIP-324D.

Make all required signal connections before

applying power to the unit. If powering via

802.3af, make sure all signal connections via the

rear panel are made then connect the VIP-821 to

the Ethernet switch.

If power is supplied via the barrel connector,

make sure all signal connections are secure.

Attach the unit to the network via the front panel

RJ-45 Ethernet connector. Apply power by

plugging the power supply in to the VIP-821 via

the barrel connector on the rear of the VIP-821.

Network Connection

The VIP-821 has one RJ-45 network connector

on the front panel.

Use a standard Ethernet patch cable to connect

the VIP-821 to an Ethernet switch. If the Ethernet

switch is 802.3af compliant the VIP-821 will draw

power from it.

Signal Connections

On the rear panel, the VIP-821 has 1 RJ-11 jack

for connection to a FXS circuit. 1 RJ-11 jack for a

failover telephone connection.

FXO Connection: Connect standard analog FXS

circuit to the VIP-821 via the rear panel RJ-11

jack labeled Line. Tip and Ring appear on pins 3

and 4 of these jacks.

Failover Connection: Connect a standard

analog telephone to the VIP-821 via the rear

panel RJ-11 jack labeled Phone. Tip and Ring

appear on pins 3 and 4 of these jacks. In the

case of a device failure, the telephone will be

able to access the FXS circuit or single line port.

REAR VIEW

Status Indicator Lights

The VIP-821 has 3 status indication lights on the

front panel.

STATUS: Flashes then illuminates to indicate

power.

3 947970

ALCOM LIMITED WARRANTY

Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under

conditions of normal use and service for a period of one year from the date of shipment. This Limited Warranty obligation shall be limited to the

replacement, repair or refund of any such defective device within the warranty period, provided that:

1. inspection by Valcom, Inc. indicates the validity of the claim;

2. the defect is not the result of damage, misuse or negligence after the original shipment;

3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus parts

and labor will be applied to units defaced or physically damaged);

4. freight charges for the return of products to Valcom are prepaid;

5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to

additional charges for parts and labor).

This Limited Warranty is in lieu of and excludes all other warranties, expressed or implied and in no event shall Valcom, Inc. be liable

for any anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase,

operation, maintenance, installation, removal or use of the product. The maximum liability of Valcom under this warranty is limited to

the purchase price of the specific Product covered by the warranty.

Disclaimer. Except for the Limited Warranty provided herein, the product is provided “as-is” without any warranty of any kind whatsoever

including, without limitation, any WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.

This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be

notified immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.

Headquarters:

Valcom, Inc.

5614 Hollins Road Roanoke, VA 24019-5056

Phone: (540) 563-2000 FAX: (540) 362-9800

ALCOMV

LINK: Indicates 100 Mbit Ethernet connection

when illuminated. No activity indicates 10 Mbit

connection.

ACT: Indicator flashes to indicate network

activity.

Front View

Setup

Information specific to your application will need

to be programmed into the VIP-821 using a

computer. The PC used for programming should

be connected to the same subnet as the VIP-821.

Setup will be done using the IP Solutions Setup

Tool. Download the latest version of the free IP

Solutions Setup Tool from Vallcom web site at

www.valcom.com/vipsetuptool.

TECHNICAL ASSISTANCE

When trouble is reported, verify power is being

supplied to the unit and there are no broken

connections. If a spare unit is available,

substitute a spare unit for the suspected defective

unit.

Assistance in troubleshooting is available from

the factory. Call (540) 563-2000 and press 1 for

Technical Support or via email at

support@valcom.com.

When requesting assistance, you should include

all available information. General information and

troubleshooting procedures are available on the

Valcom website at www.valcom.com

Valcom equipment is not field repairable.

Valcom, Inc. maintains service facilities in

Roanoke, VA. Should repairs be necessary,

attach a tag to the unit clearly stating your

company name, address, phone number, contact

person and the nature of the problem. Send the

unit to:

Valcom, Inc.

Repair & Return Dept.

5614 Hollins Road

Roanoke, Va. 24019-5056

Product specificaties

Merk:	Valcom
Categorie:	Netwerkkaart/adapter
Model:	Trunk Port VIP-821
Gewicht:	562.5 g
Breedte:	156 mm
Diepte:	133.3 mm
Hoogte:	35 mm
LED-indicatoren:	Ja
Stroom:	0.325 A
Connectiviteitstechnologie:	Bedraad
Aantal Ethernet LAN (RJ-45)-poorten:	1
Interface:	Ethernet
Netwerkstandaard:	IEEE 802.3af
Soort voeding:	24 VDC
Intern:	Nee
Power LED:	Ja
Ondersteunde netwerkprotocollen:	DHCP, IGMP v3, UDP, TCP, HTTP, Telnet, FTP
Spanning:	24 V
Hostinterface:	RJ-45
Maximale overdrachtssnelheid van gegevens:	100 Mbit/s
Netwerkgereed:	Ja
Link/Act LED:	Ja
Wifi:	Nee
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 85 procent