Valcom Station Port VIP-811 Handleiding

Valcom Netwerkkaart/adapter Station Port VIP-811

Lees hieronder de 📖 handleiding in het Nederlandse voor Valcom Station Port VIP-811 (3 pagina's) in de categorie Netwerkkaart/adapter. Deze handleiding was nuttig voor 58 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

1 947026

ISSUE 5

VIP-811

NETWORKED STATION PORT

INTRODUCTION

The VIP-811 Networked Station Port allows most

loop start terminal devices to be connected to a

managed IP-based LAN/WAN.

SPECIFICATIONS

Access Methods

 PBX, FXO Port

 POTS telephone set

Features

 RJ-45 for network connection

 1 RJ-11 telephone connections

 2 Relays with Form C contacts

 Front panel activity LED

 Network activity LEDs

 1 REN

 2.5mm jack for external power

 Power over Ethernet (PoE) 802.3af compatible

Dimensions/Weight

 1.38” H x 6.13" W x 5.25" D

(3.50cm H x 15.6cm W x 13.33cm D)

 Weight: 1.25 lbs. (0.57 kg)

Nominal Specifications

Input Impedance: 600 Ohms

Input Level: -10dBm

Output Impedance: 600 Ohms

Output Level: - 10dBm nominal

Relay Current: 1 AMP @ 24VDC

Nominal Power Requirements

Via rear panel barrel connector:

Voltage: 24VDC

Current: 325mA

Via 802.3af PoE Ethernet Switch:

802.3af: Class 3

Environment

Temperature: 0 to +40° C

Humidity: 0 to 85% non-precipitating

Packing List

Qty Item

1 VIP-811

1 VSP Document

2 Mounting Brackets W/ Hardware

4 Rubber Pads

INSTALLATION

NOTE: The telephone system referred to in this

manual is the customer premise equipment

such as an electronic key system, a PBX or a

dedicated single line telephone sets. The VIP-

811 is not intended for direct or indirect

connection to the public telephone network.

When used with a customer premise telephone

system such as a key system or PBX system,

these units are interfaced to the system via a

fully protected trunk port or system central

office port, which is a fully protected interface

device. Also, the host system must be

configured to disallow central office trunk

conferencing in order to prevent indirect

connection to the public network.

2 947026

CAUTION: To reduce the risk of electric shock,

Do not remove cover.

No user serviceable parts inside.

Refer servicing to qualified service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that dangerous

voltage constituting a risk of electric

shock is present within this unit.

This symbol indicates that there are

important operating and maintenance

instructions in the literature accompanying

this unit.

Precautionary Designations

FCC Information

This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses and can radiate radio

frequency energy and if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment

in a residential area may cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

Mounting

The VIP-811 is designed for wall or table mounting.

Table: Provided with the VIP-811 are four rubber

pads. Peel the pads from their carrier backing and

place at the four corners of the bottom of the unit.

Wall: Using the bracket and screws provided,

secure the VIP-811 to the wall.

Power Connections

The preferred method of powering a VIP-811 is via

a power over Ethernet switch meeting the 802.3af

specification.

If the rear panel barrel connector is used for power,

the preferred power supply is a Valcom VIP-324D.

Make all required signal connections before

applying power to the unit. If powering via 802.3af,

make sure all signal connections via the rear panel

are made then connect the VIP-811 to the Ethernet

switch.

If power is supplied via the barrel connector, make

sure all signal connections are secure. Attach the

unit to the network via the front panel RJ-45

Ethernet connector. Apply power by plugging the

power supply in to the VIP-811 via the barrel

connector on the rear of the VIP-811.

Network Connection

The VIP-811 has one RJ-45 network connector on

the front panel.

Use a standard Ethernet patch cable to connect

the VIP-811 to an Ethernet switch. If the Ethernet

switch is 802.3af compliant, the VIP-811 will draw

power from it.

Signal Connections

On the rear panel, the VIP-811 has 1 RJ-11 jack

for telephone connection and 1 terminal block for

relay connections.

Telephone Connections: Connect standard

analog telephones to the VIP-811 via the rear

panel RJ-11 jack labeled Phone. Tip and Ring

appear on pins 3 and 4 of these jacks.

Relay Connections: Access to the two form C

relays is provided via a six pin screw terminal

block. The relays are labeled K1 and K2. Each

relay is brought out on three terminals. The

common contact (COM) is the middle terminal with

the normally closed (N.C.) contact on the right and

the normally open (N.O.) contact on the left. Relay

contacts are rated for 1A @ 24VDC.

Rear View

3 947026

ALCOMV

Setup

Information specific to your application will need

to be programmed into the VIP-811 using a

computer. The PC used for programming should

be connected to the same subnet as the VIP-811.

Setup will be done using the IP Solutions Setup

Tool. Download the latest version of the free IP

Solutions Setup Tool from the Valcom website at

www.valcom.com/vipsetuptool.

Status Indicator Lights

The VIP-811 has 3 status indication lights on the

front panel:

STATUS: Flashes then illuminates to indicate

power.

LINK: Indicates 100 Mbit Ethernet connection

when illuminated. No activity indicates 10 Mbit

connection.

ACT: Indicator flashes to indicate network

activity.

Front View

TECHNICAL ASSISTANCE

When trouble is reported, verify power is being

supplied to the unit and there are no broken

connections. If a spare unit is available,

substitute a spare unit for the suspected defective

unit.

Assistance in troubleshooting is available from

the factory. Call (540) 563-2000 and press 1 for

Technical Support or via email at

support@valcom.com.

When requesting assistance, you should include

all available information. General information and

troubleshooting procedures are available on the

Valcom website at www.valcom.com.

Valcom equipment is not field repairable.

Valcom, Inc. maintains service facilities in

Roanoke, VA. Should repairs be necessary,

attach a tag to the unit clearly stating your

company name, address, phone number, contact

person and the nature of the problem. Send the

unit to:

Valcom, Inc.

Repair & Return Dept.

5614 Hollins Road

Roanoke, Va. 24019-5056

VALCOM LIMITED WARRANTY

Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under

conditions of normal use and service for a period of one year from the date of shipment. This Limited Warranty obligation shall be limited to the

replacement, repair or refund of any such defective device within the warranty period, provided that:

1. inspection by Valcom, Inc. indicates the validity of the claim;

2. the defect is not the result of damage, misuse or negligence after the original shipment;

3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus parts

and labor will be applied to units defaced or physically damaged);

4. freight charges for the return of products to Valcom are prepaid;

5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to

additional charges for parts and labor).

This Limited Warranty is in lieu of and excludes all other warranties, expressed or implied and in no event shall Valcom, Inc. be liable for

any anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase,

operation, maintenance, installation, removal or use of the product. The maximum liability of Valcom under this warranty is limited to the

purchase price of the specific Product covered by the warranty.

Disclaimer. Except for the Limited Warranty provided herein, the product is provided “as-is” without any warranty of any kind whatsoever including,

without limitation, any WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.

This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be

notified immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.

Headquarters:

Valcom, Inc.

5614 Hollins Road Roanoke, VA 24019-5056

Phone: (540) 563-2000 FAX: (540) 362-9800

Product specificaties

Merk:	Valcom
Categorie:	Netwerkkaart/adapter
Model:	Station Port VIP-811
Kleur van het product:	Grijs
Gewicht:	790 g
Breedte:	171.5 mm
Diepte:	241 mm
Hoogte:	44.5 mm
LED-indicatoren:	Ja
Stroom:	0.325 A
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	1
Interface:	Ethernet
Netwerkstandaard:	IEEE 802.3af
Soort voeding:	24 VDC
Intern:	Nee
Ondersteunde netwerkprotocollen:	DHCP, IGMP v3, UDP, TCP, HTTP, Telnet, FTP
Hostinterface:	RJ-45
Maximale overdrachtssnelheid van gegevens:	100 Mbit/s
Aansluiting(en):	RJ-11
Netwerkgereed:	Ja
Link/Act LED:	Ja
Wifi:	Nee
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 85 procent