Unimac LXG3000 MKII Handleiding

Unimac Nagelverzorgingsset LXG3000 MKII

Lees hieronder de 📖 handleiding in het Nederlandse voor Unimac LXG3000 MKII (29 pagina's) in de categorie Nagelverzorgingsset. Deze handleiding was nuttig voor 58 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/29

User Manual

[Revision 2 M .0 ay 2022]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE

AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may

vary in appearance, assembly, inclusions, specifications, description, and packaging.

Framing Nailer LXG3000 MkII-

E&OE © 2 2022 Unimac

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature some advice may not be –

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• - Before Use If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• - risk Keep packaging away from children

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust related collection can reduce dust-

hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non slip safety footwear, hard -

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory or

mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately if fuel gets on –

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build up in the tank to release -

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon Monoxide Safety-

• Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon a poison you -monoxide –

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors and

vents.

General Equipment Use and Care

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases or liquids etc.

• -The equipment is not weather proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

Framing Nailer LXG3000 MkII-

E&OE © 3 2022 Unimac

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Wherever possible, use a residual current

device (RCD).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot allow the equipment to –

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before , changing adjusting

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• service- Perform related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

FRAMING NAILER SAFETY

• Read and understand tool labels and all of the operating instructions, safety precautions and warnings in this manual before operating

or maintaining this nailer. Failure to follow warnings could result in DEATH or SERIOUS INJURY.

• Most accidents that result from the operation and maintenance of nailers are caused by the failure to observe basic safety rules or precautions.

An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety

procedures.

• Basic safety precautions are outlined in the Safety section of this Manual and in the sections, which contain the operation and maintenance

instructions.

• Hazards that must be avoided to prevent bodily injury or machine damage are identified by DANGERS and WARNINGS on the Nailer and in this

Manual.

• Never use this Nailer for applications other than those specified in this Manual.

• This tool has a FULL SEQUENTIAL ACTUATION ELECTRON CONTROL. First, press the push lever against the workpiece; next, pull the trigger

to drive the nail. Follow the same sequence to continue driving nails.

• This Nailer is powered by internal combustion device. This nailer shall only be used with dispensers for combustible gas which are listed in this

instruction manual.

• OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE SHIELDS. Eye protection must meet the

requirements of ANSI Standard Z87.1 and should have side shields for increased protection. If using this nailer at work, the employer you are

must be responsible for enforcing the use of eye protection equipment by the tool operator and all personnel in the work area.

• NEVER USE IN PRESENCE OF FLAMMABLE LIQUIDS OR GASES. This nailer must not be used in a combustible environment or in presence

of flammable liquids or gases, e.g., lacquer, paint, benzine, thinner or gasoline. This Nailer produces hot exhaust gases that may ignite

flammable materials and produce sparks during operation.

• DO NOT TOUCH AROUND THE EXHAUST OUTLET. This nailer produces hot exhaust gases that may ignite flammable materials. The push

lever and nose will get heated up and become hot after prolonged or rapid use. Do not touch with bare hands.

• EXPLOSION AND FIRE HAZARD. The fuel cell is an aerosol dispenser with flammable contents. Pressured container and the propellant will

remain in the fuel cell. Failure to follow instructions may result in explosion or fire. Keep the nailer, fuel cells and battery away from sunshine and

from temperature exceeding 120°F(50°C). Fuel cell and/or battery may burst, releasing flammable gas. Do not pierce or burn the container, even

after use. Do not incinerate, refill, reclaim or recycle the fuel cell. Do not spray to a naked flame or any incandescent material. Keep away from

ignitable sources No smoking. Keep out of the reach of children.-

• NEVER POINT TOOL AT YOURSELF OR OTHERS IN WORK AREA. Always assume the nailer contains fasteners. Never point the nailer at

yourself or others, whether it contains fasteners or not. If fasteners are mistakenly driven, it can lead to severe injuries. Never engage in

horseplay with the nailer. Respect the nailer as a working implement.

• KEEP FINGERS AWAY FROM TRIGGER WHEN NOT DRIVING FASTENERS TO AVOID ACCIDENTAL FIRING. Never carry the Nailer with

finger on trigger since you could drive a fastener unintentionally and injure yourself or someone else. Always carry the Nailer by the handle only.

• ALWAYS WEAR EAR AND HEAD PROTECTION. Always wear ear protection to protect your ears from loud noise. Always wear head protection

to protect your head from flying objects.

• USE OUTSIDE OR WELL-VENTILATED AREAS. This nailer exhausts carbon monoxide which are a danger to health when inhaled. This nailer

shall not be used in enclosed or poorly ventilated areas. Do not inhale.

• OPERATE WITHIN PROPER TEMPERATURE RANGE. The operating environment for this device is between 32°F (0°C) and 104°F (40°C) so

ensure to use within this temperature range. The device may fail to operate below 32°F (0°C) or above 104°F (40°C).

• STORE NAILER PROPERLY WITH FUEL CELL AND BATTERY REMOVED. When not in use, the Nailer, fuel cell and battery should be store

in tool case and in a dry place. Store indoors at temperature below 120°F (50°C). Keep the Nailer, fuel cell and battery out of direct sunlight and

out of in a vehicle. Keep out of reach of children. Look at the storage area.

• KEEP WORK AREA CLEAN. Cluttered areas invite injuries. Clear all work areas of unnecessary tools, debris, furniture, etc.

Product specificaties

Merk:	Unimac
Categorie:	Nagelverzorgingsset
Model:	LXG3000 MKII

Heb je hulp nodig?

Als je hulp nodig hebt met Unimac LXG3000 MKII stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Nagelverzorgingsset Unimac

Unimac LXG3000 MKII Handleiding

11 Februari 2023

Handleiding Nagelverzorgingsset

Nieuwste handleidingen voor Nagelverzorgingsset

Physa FR-6 Handleiding

4 November 2024

Physa FR-7 Handleiding

4 November 2024

Physa FR-11 Handleiding

4 November 2024

Physa FR-09 Handleiding

4 November 2024

Medel Manicure/Pedicure Expert Handleiding

27 September 2024

Valera ManiSwiss Travel Handleiding

3 September 2024

Medisana ND 850 Handleiding

17 Mei 2024

Homedics Heel Smoother PED-600 Handleiding

27 Maart 2024

Homedics Time to Shine MAN-600 Handleiding

27 Maart 2024

Homedics MAN-3023A Handleiding

27 Maart 2024