Tycon Systems RPAL48-180-1000 Handleiding

Tycon Systems Zonnepaneel RPAL48-180-1000

Lees hieronder de 📖 handleiding in het Nederlandse voor Tycon Systems RPAL48-180-1000 (4 pagina's) in de categorie Zonnepaneel. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

RPAL48-180- xxxx

200W RemotePro™

▫ Wireless Base Stations

and Client Devices

▫ Surveillance Cameras

▫ Remote Control

▫ Remote Lighting

▫ Off Grid Electronics

Congratulations! on your purchase of the RemotePro 200W ™

Remote Power System. Please take a moment to review this

Qwik Install Guide before use.

Operation Modes: Solar Only operation or Solar with AC/DC

Backup.

Key Features: Industrial Strength, Manageable, 24VDC and

48VDC Output, 7 Gigabit Passive PoE ports, 2.25A Aux Port,

48V 20A MPPT Solar, Automated Alerts, Removable Connec-

tions.

Safety: For your own protection, follow these safety rules.

▫ Perform as many functions as possible on the ground

▫ Do not attempt to install on a rainy, windy or snowy day or if

there is ice or snow accumulation at the install site or if the

site is wet.

▫ Make sure there are no people, pets, etc. below if you are

working on a roof or ladder.

Recommended Tools: Phillips and Small Flat Blade Screwdriv-

ers, 6mm Hex key and 13, 19, 27, 34mm Wrenches

Please help preserve the environment and return

any used batteries to an authorized depot

Qwik Install

STEP 1: Select install location where southern sky has no obstructions

that could cause shading on solar panels.

STEP 2: Pour a foundation big enough to hold solar mount anchors

and also provide level support for battery box. See detailed instructions

in solar mount instructions.

STEP 3: Assemble solar array with mount using solar mount instruc-

tions.

STEP 4: Place battery box under solar panels facing towards back of

solar panels. Install 8 batteries in the box in an alternating pattern. Use

rope tied to battery tabs to lower batteries into the box. Connect all 8

batteries in series configuration (Positive to Negative to Positive...)

STEP 5: Install DIN rail to enclosure using the two screws provided.

Install MPPT solar controller to DIN Rail. Remove the Large Green

Connector from the unit.

STEP 6: Find the thermocouple cable that came with the MPPT Solar

Controller and connect the side with the ring lug to one of the batteries

positive or negative terminals, it doesn t matter which one. Connect the ’

battery cable to the Large Green Connector battery inputs and then to

the batteries making sure to observe the proper polarity.

STEP 7: Install the cable glands in the back of the enclosure and route

the long solar panel cables through the cable gland and connect to the

large green connector solar (PV) inputs. A four panel system will use

two of the long cables and a two panel system will use one of the long

cables. You can shorten the cables as necessary for a cleaner install.

You can also lengthen the cables by adding additional lengths of

12AWG cable.

STEP 8: Connect two of the solar panels in series (Positive to Nega-

tive) by plugging the positive from panel 1 to the negative of panel 2

and then connect the long solar cable to the remaining positive and 20’

negative connectors from the solar panels. The connectors are keyed

for polarity so they cannot be connected incorrectly. Repeat for a four

panel system.

STEP 9: Once the batteries and solar panels are all connected and

wired to the Large Green Connector, Disconnect PV+ wire and plug the

connector to the MPPT Solar Controller until the connector latches click

into place. The Battery Charging LED should light up for about 60 sec-

onds. Now connect PV+ to the green connector. Battery should Note:

always be connected first and disconnected last from the controller.

STEP 10: Plug the temperature sensor to the Temp Sensor input on

the MPPT Solar Controller. Refer to the TPDIN SC48 20 instruction - -

manual for setup and operation of the MPPT Solar Controller.

STEP 11: Tighten the cable glands on the wires to make weatherproof

connections. Plug unused holes using the supplied hole plugs. If de-

sired, attach the enclosure to the solar mount pole using chain or cable

for security.

STEP 12: You may want to put a fine screen over the vent holes on

either end of the enclosure to keep out insects. Window screen works

well. Be sure to secure the cables so they won t move in the wind. All ’

Product specificaties

Merk:	Tycon Systems
Categorie:	Zonnepaneel
Model:	RPAL48-180-1000
Kleur van het product:	Zwart, zilver
Gewicht:	468000 g
Stroom:	2.25 A
Uitgangsspanning (max):	48 V
Uitgangsspanning (min):	24 V
Nominaal vermogen:	1000 W
Installatietype:	Grond