Sharp NU-JB395 Handleiding

Sharp Zonnepaneel NU-JB395

Lees hieronder de 📖 handleiding in het Nederlandse voor Sharp NU-JB395 (6 pagina's) in de categorie Zonnepaneel. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

SIM02E-001

PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PV MODULES.

PLEASE PASS ALONG THE ATTACHED USER MANUAL TO YOUR CUSTOMER.

INSTALLATION MANUAL

– Crystalline Photovoltaic Module –

# IMPORTANT SAFETY INSTRUCTIONS p.1

# GENERAL INSTRUCTIONS p.1 ~ p.3

# INSTALLATION INSTRUCTIONS -PHOTOVOLTAIC MODULES- p.4

# ELECTRICAL OUTPUT AND THERMAL CHARACTERISTICS p.4

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important safety instructions for the PV module

that must be followed during the maintenance of PV modules.

To reduce the risk of electric shock, do not perform any servicing

unless you are qualied to do so.

1. The installation must be performed by a certied installer

/servicer to ensure system integrity and safety.

2. The installation is only allowed after referring and

understanding of this INSTALLATION MANUAL. If you don’t

have your personal copy, please contact your installer or local

SHARP oce listed in SHARP Solar web site:

URL: https://global.sharp/solar/en/

3. Do not pull the PV cables.

4. Do not touch any surface of PV module.

5. Do not place/drop objects onto the PV modules.

6. Do not disassemble or attempt to repair the PV module by

yourself.

7. Do not drop the PV module.

8. Do not damage, pull, bend, or place heavy material on cables.

9. Upon completion of any service or repairs, ask the

installer/servicer to perform routine checks to determine that

the PV modules are in safe and proper operating condition.

10. When replacement parts are required, be sure the

installer/servicer uses parts specied by the manufacturer with

same characteristics as the original parts. Unauthorized

substitutions may result in re, electric shock, or other hazard.

11. Consult your local building and safety department for required

permits and applicable regulations.

12. As a result of sliding snow, the mechanical load increases when

the number of PV module rows in the matrix of a PV installation

increases. When mounting the PV module in the portrait

orientation for more than 3 rows, the accumulated snow load

may cause the lower edge of the PV module frame to deform.

Take necessary measures (e.g. snow stopper) to avoid

possible damage.

13. Periodically remove any overhanging snow and/or ice from the

PV module framework as it may cause deformation of the PV

module frame.

GENERAL INSTRUCTIONS

1. INTRODUCTION

This INSTALLATION MANUAL contains essential information for the electrical and mechanical installation that you must know

before installing SHARP PV modules. This also contains safety information you need to be familiar with. All the information

described in this manual are the intellectual property of SHARP and based on the technologies and experiences that have been

acquired and accumulated in the long history of SHARP. This document does not constitute a guaranty, expressed or implied.

SHARP does not assume responsibility and expressly disclaims liability for loss, damage, or expense arising out of or in any way

connected with installation, operation, use or maintenance of the PV modules. No responsibility is assumed by SHARP for any

infringement of patents or other rights of third parties that may result from use of PV module. SHARP reserves the right to make

changes to the product, specications or INSTALLATION MANUAL without prior notice.

2. COMPONENTS

3. GENERAL INFORMATION

(INCLUDING WARNING AND SAFETY)

The installation of PV modules requires a great degree of skill

and should only be performed by a qualied licensed

professional, including licensed contractors and licensed

electricians. Please be aware that there is a serious risk of

various types of injury occurring during the installation including

the risk of electric shock. All SHARP PV modules are equipped

with a permanently attached junction box that will accept variety

of wiring applications or with a special cable assembly for ease

of installation, and they do not require special assembly.

GENERAL WARNING

1. PV modules are heavy. Handle with care.

2. Before you attempt to install, wire, operate and maintain

the PV module, please make sure that you completely

understand the information described in this

INSTALLATION MANUAL.

3. Contact with electrically active parts of a PV module such

as terminals can result in burns, sparks and lethal shock

whether the PV modules are connected or not.

4. PV modules produce electricity when the sucient sunlight

or other sources illuminate the PV module surface. When

the PV modules are connected in series, voltage is

cumulative. When the PV modules are connected in

parallel, current is cumulative. As a result, a large-scale PV

MODEL

NU-JBxxx

CAUTION: HIGH VOLTAGE

To reduce the risk of electric shock, do not touch.

Solar Photovoltaic Cell

Junction Box

Superstrate Glass

Frame

Connector

Electrical Cable

SIM02E-001

system can produce high voltage and current which could

present an increased hazard and may cause serious injury

or death.

5. Do not connect the PV modules directly to the loads such

as motor since the variation of the output power depending

on the solar irradiation causes damage for the connected

motor.

1: In the case of a brushless motor, the lock function

becomes active and the hall IC is most likely to be

damaged.

2: In the case of a brush type motor, the coil is most likely

to be damaged.

6. In case of snow build-up, snow would slide easier on the

smooth surface of the PV module than other parts of the

roof. Snow may suddenly slide, fall o the roof and hit

nearby objects/areas. Take preventive measures (e.g.

snow stopper) when there is possible risk such case would

cause an injury or a damage.

GENERAL SAFETY

1. Consult local codes and other applicable laws concerning

required permits on regulations for installation and

inspection requirements.

2. Before installing a PV module, contact appropriate

authorities to determine permit, installation and inspection

requirements that should be followed.

3. Install PV modules and ground frames in accordance with

applicable rules and regulations.

4. PV modules should be installed and maintained by

qualied personnel. Only installer/servicer personnel

should have access to the PV module installation site.

5. No matter where the PV modules are installed, either roof

mounted construction or any other type of structures above

the ground, appropriate safety practices should be followed

and required safety equipment should be used in order to

avoid possible safety hazards. Note that the installation of

some PV modules on roofs may require the addition of

reproong, depending on local building/re codes.

6. In the case that the PV modules are non-integral type, the

PV module is to be mounted over a re resistant roof.

7. Use PV modules with the same cell size within series.

8. Follow all safety precautions of other components that are

used in the system.

9. In order to avoid a risk of injury or electrical shock, do not

allow anyone to approach the PV module if the person

has little knowledge on PV module or on the measures that

should be taken when PV modules are damaged.

10. Do not shade portions of the PV module surface from the

sunlight for a long time. The shaded cell may become hot

(hot spot phenomenon) which results in solder joints

peeling o. Shading causes drop in generated power

and/or operation failure of the PV modules.

11. Do not clean the glass surface with chemicals. Do not let

water collect on the glass surface for a long time. This

creates a risk of white eorescence (glass disease) which

may result in the deterioration of energy generation.

12. Do not install the PV module horizontally. It may cause dirt

or white eorescence (glass disease) due to water.

13. Do not cover the water drain gap of the frame. There is a

risk of frost damage when the frame is filled with water

cumulation.

14. If there is a risk of sliding snow, an appropriate measure

has to be taken so that PV module frames on lower edge

of PV modules will not be damaged.

15. Do not expose PV module to sunlight concentrated with

mirrors, lenses or similar means.

16. Turn o inverters and circuit breakers immediately, should

a problem occur.

17. In case the glass surface of a PV module is broken, wear

goggles and tape the glass to keep the broken pieces in

place.

18. A defective PV module may generate power even if it is

removed from the system. It may be dangerous to handle

the PV module while exposed to sunlight. Place a defective

PV module in a carton so PV cells are completely shaded.

19. In case of series connection, the maximum open circuit

voltage must not be greater than the specied maximum

system voltage. The voltage is proportional to the number

of series. In case of parallel connection, please be sure to

take proper measure (e.g. fuse for protection of PV module

and cable from over current, and/or blocking diode for

prevention of unbalanced strings voltage) to block the

reverse current ow. The current may easily ow in a

reverse direction.

20. Keep PV modules away from children.

HANDLING SAFETY

1. Do not cause an excessive load on the surface of PV

module or twist the frame. The glass surface can easily

break.

2. Do not stand or step on the PV module. The surface glass

of PV module is slippery.

3. Do not hit or put excessive load on the glass or back sheet.

The PV cell is very thin and can be easily broken.

4. Do not scratch or hit at the back sheet. The back sheet is

vulnerable.

5. Do not damage the junction box or do not pull the cables.

The junction box can crack and break.

6. Never touch junction box or the end of output cables with

bare hands when the PV module is irradiated. Cover the

surface of PV module with cloth or other suitable

suciently opaque material to isolate the PV module from

incident light and wear rubber gloves when handling the

wires to avoid electric shock.

7. Do not scratch the output cable or bend it with force. The

insulation of output cable can break and may result in

electricity leakage or shock.

8. Do not pull the output cable excessively. The output cable

may unplug and cause electricity leakage or shock.

9. Do not drill holes in the frame. It may compromise the

frame strength and cause corrosion.

10. Do not scratch the insulation coating of the frame (except

for grounding connection). It may cause corrosion of the

frame or compromise the framework strength.

11. Do not touch the PV module with bare hands. The frame of

PV module has sharp edges and may cause injury.

12. Do not drop PV module or allow objects to fall down on the

PV module.

13. Do not concentrate sunlight articially on the PV module.

14. Do not hold the PV module on one side. The frame may

bend or twist. Hold the PV module at opposite sides.

INSTALLATION SAFETY

1. Always wear protective head gear, insulating gloves and

safety shoes (with rubber soles). Do not wear metallic

jewellery to prevent electric shock during installation.

2. Keep the PV module packed in the carton until installation.

3. Do not touch the PV module unnecessarily during

installation. The glass surface and the frames get hot.

There is a risk of burn, or electric shock.

4. Do not work under rain, snow or windy conditions.

5. Use dry insulated tools.

6. Do not drop tools or hard objects on PV modules

7. When working at heights, wear a safety belt and take care

not to drop any items (e.g., PV module or tools).

8. Make sure ammable gases are not generated near the

installation site.

9. Completely cover the PV module surface with an opaque

material during PV module installation and wiring.

10. Plug in the connector tight and ensure the wiring work.

Make sure that the connectors have been locked by a

snap-in latch. Any treatments over the connectors which

may allow to unlock the snap-in latch shall not be done.

11. Due to the risk of electrical shock, do not perform any work

if the terminals of PV module are wet.

12. Do not touch the junction box and the end of output cables,

the cable ends (connectors) , with bare hands during

installation or under sunlight, regardless of whether the PV

module is connected to or disconnected from the system.

13. Do not unplug the connector if the system circuit is

connected to a load.

14. Do not stomp on the glass at work. There is a risk of injury

or electric shock if glass is broken.

15. Do not work alone (always work as a team of 2 or more

people).

16. Do not damage the back sheet of PV modules when setting

the equipotential bonding by bolts.

17. Do not damage the surrounding PV modules or mounting

structure when replacing a PV module.

18. Bind cables by the insulation locks. Drooping down of

cables from the junction box could possibly cause various

problems such as animal biting, electricity leakage in

puddle.

19. Take proper measures for preventing the laminate

(consisted of resin, cells, glass, back sheet, etc.) from

dropping out of the frame in case the glass is broken.

20. Plastic components such as cables or connectors shall be

located so that they will not be exposed to direct sunlight

after installation to prevent degradation of them.

21. If batteries are used with PV modules, follow safety

precautions of the battery manufacturer.

22. In case of extreme snow build-up, the weight of the snow

may cause the PV module’s frame to deform. Take

SIM02E-001

appropriate preventive measures to minimize any possible

resulting damage.

4. SITE SELECTION

In most applications, the PV modules should be installed in a

location where there is no shading throughout the year. In the

Northern Hemisphere, the PV modules should typically face

south, and in the Southern Hemisphere, the PV modules should

typically face north.

Please make sure that there are no obstructions in the

surroundings of the site of installation. TAKE PROPER STEPS

in order to maintain reliability and safety, in case the PV modules

are used in areas such as: Heavy snow areas / Extremely cold

areas / Strong wind areas / Installations over, or near, water /

Areas where installations are prone to salt water

damage/corrosive gas environment/ Small islands or desert

areas.

The results of the ammonia test and the salt-mist-corrosion test

on the PV modules, carried out under such strict test conditions,

should be disclosed for reference purposes only. The decision

on whether the PV modules are suitable and compatible for

each installation eld will depend on the user’s judgement and

responsibility.

5. TILT ANGLE

The tilt angle is the measurement between the PV module and

a horizontal ground surface. The PV module generates the

maximum output power when it faces the sun directly.

5 degrees or more is recommended for the tilt angle of the PV

module for the maintenance. (See 9. Maintenance)

For the standalone systems with a battery where the PV

modules are attached to a permanent structure, the tilt angle of

the PV modules should be determined to optimize the

performance when the sunlight is the scarcest. In general, if the

electric power generation is adequate when the sunlight is the

scarcest, then the angle chosen should be adequate during the

rest of the year. For grid-connected installations where the PV

modules are attached to a permanent structure, it is

recommended to tilt the PV module at the angle equal to the

latitude of the installation site so that the power generation from

the PV module will be optimum throughout the year.

6. WIRING

To ensure proper system operation and to maintain your

guaranty, observe the correct cable connection polarity (Figures

1 & 2) when connecting the PV modules to a battery or to other

PV modules. If not connected correctly, the bypass diode could

be destroyed.

PV modules can be wired in series to increase voltage.

Connect wires from the positive terminal of one PV module to

the negative terminal of the next PV module. Figure 1 shows PV

modules connected in series.

Connect PV modules in parallel to increase current. Connect

wires from the positive terminal of one PV module to the positive

terminal on the next PV module. Figure 2 shows PV modules

connected in parallel.

7. GROUNDING

The frame grounding must consider the local requirement and

regulation at the installation site. When grounding is required,

please refer to below example connection (Figure 3). Please be

careful in arranging the system ground so that the removal of

one PV module from the circuit will not interrupt the grounding

of any other PV modules.

The PV modules should be grounded to the same electrical

point as described below.

You can use a hole with the appropriate symbol for

equipotential bonding on the side frame for either a bolt, nut and

washer grounding the PV module to the frame, a ground lug

fastened by bolt or screw, or appropriate screw (hardware not

provided). An example of acceptable ground connection using

a bolt, nut and washer retaining a ground lug is shown in Figure

3. In a connection of this type, the hardware (such as a toothed

locked washer / star washer) must score the frame surface to

make positive electrical contact with the frame. The ground wire

must be considered within the local requirement of local and

regulation at the site of installation.

8. MOUNTING

Please make sure that all the information described in the

INSTALLATION MANUAL is still valid and proper for your

installation. The mounting method has been veried by SHARP

and NOT CERTIFIED by a third party organization.

The approved way to mount SHARP PV modules to a support

structure is described in this INSTALLATION MANUAL.

Although SHARP does not specify or warrant frame clips or

clamps, using frame clips (not provided) or clamps (not

provided) is possible when they are designed for PV modules

and with minimum dimensions on the sides of the PV module in

accordance with the instructions and drawings provided. If using

frame clips or clamps, the PV modules should be xed rigidly

and there shall be no damage to the PV modules by deforming

mounting structure against design load.

The SHARP PV module guaranty may be void if customer-

selected frame clips are improper or inadequate for PV module

properties (including strength or material) or installation. Note

that if metal clips are used, there must be a path to ground from

the clips, (for instance, using star washers in the clip hardware

set). Please review the descriptions and drawings carefully; not

mounting the PV modules according to one of these methods

may void your guaranty. The PV module has passed the test

sequence which contains 3 cycles each performed at 5,400 Pa

positive and 2,400 Pa negative loading in accordance with

IEC61215-2.

Support structures that PV modules are mounted on should be

rigid. SHARP PV modules are designed to ensure optimal

electrical performance under the condition that they are

mounted on rigid support structures. Deformation of support

structure may damage PV module with its electric performance.

When mounting the PV module on structure, ensure that no

corner has a displacement of more than 2mm per every

1000mm of the diagonal.

The mounting structure shall enable

the PV module to deect freely under wind and/or snow load not

to make direct impact to the center of the PV module. (i.e. min.

10 cm from the roof surface to the bottom face of PV module

frame)

9. MAINTENANCE

The PV modules are designed for long life and require very

little maintenance. If the angle of the PV module is 5 degrees or

more, normal rainfall is sucient to keep the PV module glass

surface clean under most weather conditions. If dirt build-up

becomes excessive, use only a soft, damp cloth and water to

clean the glass. If cleaning the back of the PV module is

required, take utmost care not to damage the back side

materials. In order to ensure the operation of the system, check

the connection of wiring and the state of the jacket of wires

occasionally.

For PV modules with anti-reective coating glass, do not touch

the glass since nger prints or stains will easily mark. If dirt build-

up becomes excessive, clean the glass surface with water only.

Bypass Diode

(Built-in Junction Box)

Bypass Diode

(Built-in Junction Box)

Product specificaties

Merk:	Sharp
Categorie:	Zonnepaneel
Model:	NU-JB395
Kleur van het product:	Zwart
Gewicht:	23500 g
Breedte:	1002 mm
Diepte:	40 mm
Hoogte:	2008 mm
Materiaal behuizing:	Aluminium
Internationale veiligheidscode (IP):	IP68
Stroom:	20 A
Bedrijfstemperatuur (T-T):	-40 - 85 °C
Nominaal vermogen:	395 W
Kortsluitstroom (lsc):	10.35 A
Maximale systeemspanning:	1500 V
Type zonnecel:	Monokristallijn silicium
Celrendement:	19.6 procent
Spanning bij maximaal vermogen (Vmp):	41.07 V
Spanning bij open-circuit (Voc):	49.45 V
Stroom bij maximaal vermogen (Imp):	9.62 A
Aantal cellen:	144