Tripp Lite PowerVerter APSX4048SW Handleiding

Tripp Lite Accu PowerVerter APSX4048SW

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite PowerVerter APSX4048SW (48 pagina's) in de categorie Accu. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/48

Owner’s Manual

Sine Wave DC-to-AC Inverter/Charger

Model: APSX4048SW

48 VDC to 230 VAC

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Table of Contents

Important Safety Instructions 2

1. Overview & Features 3

1.1 Overview 3

1.2 Front Panel Controls, LCD Screen 3

and LED Indicators

1.3 Optional Features 4

2. Battery Charger 4

2.1 Mode of Operation 4

2.2 Transfer Switching Speed 4

3. Battery Installation 4

and Maintenance

3.1 Select Battery Type 4

3.2 Monthly Maintenance 6

3.3 Battery Installation 6

3.4 Battery Connection 6

4. Inverter/Charger Single-Phase 9

Installation

4.1 Installation 9

4.2 Installation Diagrams and Charts 9

4.3 Installation and Start-Up 10

4.4 Single-Phase Parallel Stacking 11

Installation and Start-Up

5. Inverter/Charger 3-Phase 13

Parallel Installation

5.1 Installation 13

5.2 Installation Diagrams and Charts 13

5.3 Installation and Start-Up 14

6. Operation 16

6.1 Modes of Operation 16

(Single and 3-Phase)

6.2 Settings and Parameters 18

6.3 Single-Phase Parallel Operation 20

6.4 3-Phase Parallel Operation 21

7. Technical Speciﬁcations 22

8. Troubleshooting 22

9. Service 23

Русский 24

PROTECT YOUR INVESTMENT!

You could also win an ISOBAR6ULTRA surge protector—a $50 value!

www.tripplite.com/warranty

Important Safety Instructions

SAVE THESE INSTRUCTIONS!

This manual contains important instructions and warnings that should be followed during the installation,

operation and storage of all Tripp Lite Inverter/Chargers.

Location Warnings

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner will seriously

inhibit the unit’s internal cooling, eventually causing product damage not covered under warranty.

• Install your Inverter/Charger in a location or compartment that minimizes exposure to heat, dust, direct sunlight and

moisture. Flooding the unit with water will cause it to short-circuit and could cause personal injury due to electric shock.

• For proper ventilation, allow a minimum 2 inches of clearance at front and back of the Inverter/Charger. To avoid overheating

the Inverter, the compartment that houses the Inverter/Charger must be properly ventilated with adequate outside air ﬂow.

The heavier the load of connected equipment, the more heat will be generated by the unit.

• Do not install the Inverter/Charger near magnetic storage media, as this may result in data corruption.

• Do not install the Inverter/Charger near ﬂammable materials, fuel or chemicals.

Battery Connection Warnings

• Multiple battery systems must be comprised of batteries of identical voltage, age, amp-hour capacity and type.

• Because explosive hydrogen gas can accumulate near batteries if they are not well ventilated, do not install batteries in a

“dead air” compartment. The battery compartment should have some ventilation to outside air.

• Sparks may result during ﬁnal battery connection. Always observe proper polarity as batteries are connected.

• Do not allow objects to contact the DC input terminals. Do not short or bridge these terminals together. Serious personal

injury or property damage could result.

Ground Connection Warnings

• Safe operation requires connecting the Inverter/Charger’s Main Ground Terminal directly to the frame of the vehicle or

earth ground.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause

the failure of the life support equipment or to signiﬁcantly affect its safety or effectiveness is not recommended. Do not

use this equipment in the presence of a ﬂammable anesthetic mixture with air, oxygen or nitrous oxide.

• You may experience uneven performance results if you connect a surge suppressor, line conditioner or UPS system to the

output of the Inverter/Charger.

• User must supply proper protection for wire openings in unit panels.

Operation Warnings

• Your Inverter/Charger does not require routine maintenance.

• Potentially lethal voltages exist within the Inverter/Charger as long as the battery supply is connected. During any service

work, the battery supply should therefore be disconnected.

• Do not connect or disconnect batteries while the Inverter/Charger is operating from the battery supply. Dangerous arcing may

result.

Status

APSX4048SW

DOWN

SET ENTER

Fault

3 54

1. Overview and Features

1.1 Overview

• Tripp Lite’s APSX4048SW Sine Wave Inverter/Charger is a heavy-duty unit generating a pure sine wave in single-phase or

3-phase power from a 48V battery bank. The APSX4048SW can supply power to a wide range of connected equipment,

from heaters, air conditioners, refrigerators and vacuum cleaners to computers and peripheral devices. The APSX4048SW is

designed to work in heavy load conditions, so de-rating is unnecessary.

• The APSX4048SW’s smart charger is compatible with various battery types and sizes. The switch module automatically

diverts the energy transfer path between the Inverter and an AC input. When the AC source is lower than the transfer level,

the electrical path switches to the Inverter and draws power from the battery source. Otherwise, the load is powered by the

AC input.

1.2 Front Panel Controls

1.2.1 Controls, LCD Screen and LED Indicators

1 This 2-line dot matrix display LCD Screen:

indicates a wide range of power inverter

operating conditions and diagnostic data. It

also displays Inverter/Charger settings and

options when in SETTING mode.

2 This button offers 3 main ON/OFF Button:

functions depending on the power input

when pressed:

• CHARGING/STANDBY switching

(when used with AC input).

• INVERTING/STANDBY switching

(when used with DC input).

• STANDBY mode

(AC bypass output and no charge).

3 Return to previous page.SET Button:

4 This button allows you DOWN Button:

to browse through different operating

conditions and options on the LCD display.

Pressing down the DOWN button for an

extended duration allows the cursor in the

LCD screen to change to a different position.

5 UP Button: This button allows you to browse through different operating conditions and options on the LCD display.

Pressing down the UP button for an extended duration allows the cursor in the LCD screen to change to a different

position.

6 This button allows you to select an item in the menu.ENTER Button:

7 STATUS LED

8 FAULT LED: This red light will ﬂash when your inverter detects an internal fault (overheating, overvoltages, etc.) or when it

detects a wiring fault from the AC or DC power source (reversed phases, missing ground, etc.).

Product specificaties

Merk:	Tripp Lite
Categorie:	Accu
Model:	PowerVerter APSX4048SW
Kleur van het product:	Wit
Gewicht:	25850 g
Breedte:	184.2 mm
Diepte:	571.5 mm
Hoogte:	228.6 mm
Gewicht verpakking:	26760 g
Breedte verpakking:	317.5 mm
Diepte verpakking:	787.4 mm
Hoogte verpakking:	299.7 mm
Vormfactor:	Compact
Land van herkomst:	Taiwan
Accu/Batterij voltage:	48 V
Uitgangsvermogen:	4000 W
Frequentie:	- Hz
(Buitenste) hoofdverpakking hoogte:	299.7 mm
(Buitenste) hoofdverpakking breedte:	317.5 mm
(Buitenste) hoofdverpakking brutogewicht:	26760 g
(Buitenste) hoofdverpakking lengte:	787.4 mm
Hoeveelheid per (buitenste) hoofdverpakking:	1 stuk(s)
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Stopcontacttypes:	Eindstation
Output power capacity:	- kVA
Ingang operation voltage (min):	220 V
Ingang operation voltage (max):	240 V
Uitgang operation voltage (min):	220 V
Uitgang operation voltage (max):	240 V
Uitgangsspanningsregeling:	2 procent
Uitgangsfrequentieregeling:	50 - 60 Hz