Trek Sensor Handleiding
Trek
Fietscomputer
Sensor
Lees hieronder de 📖 handleiding in het Nederlandse voor Trek Sensor (4 pagina's) in de categorie Fietscomputer. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
Page 1
Trek Sensor Cycling Computer
Owners Manual
Congratulations and thank you for purchasing the Trek Sensor Cycling
Computer. Before operating please read this instruction manual carefully and
retain it for future reference. We recommend setting the speed scale and
wheel circumference before installing the computer.
Precautions
Remember to watch the road or trail while riding. Watching your bicycle
computer makes it difficult to see upcoming obstacles. Awareness of potential
road, trail or traffic problems should be your main concern.
Main Unit/Accessories
1
2
3
45
6
7
8
Contents:
1. Main Unit
2. Bracket
3. Wire
4. Wheel Sensor
5. Magnet
6. Wire Securing Tape
7. Zip Tie
8. Bracket Rubber Pad
alone will remain flashing on the screen as in fig. 3. To
make choice please insert computer head into main
bracket. Bring Magnet in contact with tip of wheel
sensor. (fig. 5) Screen will flash between KM and Mi.
When desired choice is on screen pull magnet away
from wheel sensor to lock choice and move on to next
step. (See fig. 4)
If incorrect data appears on the screen, please re-
install battery again.
4. Setting the wheel circumference (100mm-
2999mm)
2155 is displayed and the last 5 is flashing. To change
this number hold the magnet to the tip of the sensor (fig. 5) and scroll
through numbers. When the desired number is
present pull the magnet away. Do this
procedure until all four numbers are set. The display
will then enter the auto-scan mode.
Installation
When you have completed your preparation, please
follow the steps below to install. In order to install smoothly, please take off
the computer from the bracket temporarily.
1. Place bracket and bracket rubber pad on handlebar.
2. Place two zip ties through bracket.
3. Position bracket in desired location and remove extra zip tie.
4. With computer in bracket, adjust to the right position.
Table 1. Setting values reference table
Preparation - Must be completed before operation
1. Measure the wheel circumference before setup refer
to fig. 1 (25.4 mm equals 1 inch) or Table 1 to get the
wheel circumference in millimeters. Confirm and note
this number in the manual for later use here:
_______________
2. Installing/Replacing the battery.
Remove the battery cover by using a narrow flat blade or similar opener
as illustrated in fig. 2. Insert a new battery (3v) CR2032, position the (+)
pole upward as illustrated. Place the battery properly into the case and
close the cover securely. After the battery is installed speed scale and
wheel size can be set.
3. Setting Speed Scale Choose KM for Kilometers or Miles.
After the battery is installed all displays will be illuminated, then “KM”
Page 3Page 2
Wheel/Tire Size Wheel size Setting Wheel/Tire Size Wheel size Setting
16” 1300 700 X 20C 2074
20” X 1.75” 1600 700 X 23C 2085
24” X 1.95” 1920 700 X 25C 2100
26” X 1” 1950 700 X 28C 2135
650 X 20C 1945 700 X 32C 2155
650 X 23C 1990 700 X 35C 2175
26” X 1.5” 2030 700 X 38C 2180
26” X 1.9” 2055 700 X 40C 2190
26” X 2.0” 2074 700 X 1-1/4” 2160
26” X 2.2” 2100
Measure the distance which
is your circumference
First
Point
Second
Point
fig 2
fig 3fig 4
fig 5
Odometer (total distance)
(0.0-9999 kms or 6213 miles)-ODO
The total distance is continuously measured, accumulated and
displayed until next reset or the battery is changed. When 9999
kms or 6213 miles is reached the odometer returns to zero and
counting begins anew.
Trip Distance
(0.0-999.9 kms)-DIS
The trip distance from start to current point is displayed. Trip
distance will start calculating if signal is received, and stop
calculating when signal stops.
Auto Start/Stop
All functions - Current Speed(S), Odometer(ODO) and Trip Distance(DIS) will
automatically start and stop when signal is received or stopped.
Auto Scan
All the functions (ODO, DIS) will automatically scan and each display mode will
last 3 seconds. This function will continue until battery change/reset.
Auto Power Saving
When unit has not been used for 10 minutes (no signal received for ten
minutes continuously), the display will disappear and power will be
automatically saved. Start pedaling to release power saving mode and display
all functions automatically (auto scan).
Auto Clear data
When unit has not been used for 6 hours (not receiving and input signal for 6
hours continuously), all data stored in memory will be erased (wheel
circumference, odometer and speed scale will be kept). Once you start
pedaling (receiving signals), all data will calculate from zero.
5. Loosen the spoke screw and place spoke in spoke channel.
6. Tighten spoke screw so that it cinches the magnet securely
to the spoke.
7. Place the wheel sensor on the appropriate fork leg.
8. Install the zip tie through wheel sensor and pull tight.
9. Adjust the wheel sensor until it is 3-5mm from the wheel magnet. The
magnet should line up with indent on wheel sensor.
Test
Mount the computer in the bracket. Lift the front wheel off the ground and
spin the wheel checking if current speed is displayed. If not, adjust wheel
magnet and wheel sensor as described in installation steps 9. Refer to the
following steps for the operation of your Sensor computer.
Display Functions
Current Speed (0.0-70 miles or 99
kms)-S
The current speed is displayed on the upper line of the display and updated
every second.
Page 5Page 4
Spoke
Screw
Spoke
Channel
Speed 0-30km/h 31-60km/h over 60 m/h
Minimal display unit 0.1km/h(mile/h) 0.5km/h(mile/h) 1km/h(mile/h)
Product specificaties
Merk: | Trek |
Categorie: | Fietscomputer |
Model: | Sensor |
Heb je hulp nodig?
Als je hulp nodig hebt met Trek Sensor stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Fietscomputer Trek
9 September 2023
9 September 2023
9 September 2023
9 September 2023
9 September 2023
9 September 2023
9 September 2023
9 September 2023
9 September 2023
9 September 2023
Handleiding Fietscomputer
- Fietscomputer Bosch
- Fietscomputer Garmin
- Fietscomputer Pioneer
- Fietscomputer Topcom
- Fietscomputer Union
- Fietscomputer Asaklitt
- Fietscomputer Ascent
- Fietscomputer Ascot
- Fietscomputer Assize
- Fietscomputer Bafang
- Fietscomputer Batavus
- Fietscomputer BBB Cycling
- Fietscomputer Bikemate
- Fietscomputer Bontrager
- Fietscomputer Bryton
- Fietscomputer Btwin
- Fietscomputer Decathlon
- Fietscomputer Echowell
- Fietscomputer Falk Outdoor
- Fietscomputer Filmer
- Fietscomputer Filzer
- Fietscomputer Gazelle
- Fietscomputer Halfords
- Fietscomputer Hema
- Fietscomputer IGPSport
- Fietscomputer Key Disp
- Fietscomputer Knog
- Fietscomputer Kogan
- Fietscomputer Matrabike
- Fietscomputer Mavic
- Fietscomputer Maxxus
- Fietscomputer Mio
- Fietscomputer Navman
- Fietscomputer Polar
- Fietscomputer Powertap
- Fietscomputer Pro
- Fietscomputer Prophete
- Fietscomputer Pyle
- Fietscomputer QT Cycle Tech
- Fietscomputer Rawlink
- Fietscomputer Shimano
- Fietscomputer Sigma
- Fietscomputer Sigma Sport
- Fietscomputer Silent Force
- Fietscomputer Speedmaster
- Fietscomputer Stages Cycling
- Fietscomputer Stamm
- Fietscomputer Stella
- Fietscomputer Suunto
- Fietscomputer Timex
- Fietscomputer Trelock
- Fietscomputer VDO
- Fietscomputer VDO Dayton
- Fietscomputer Ventura
- Fietscomputer VETTA
- Fietscomputer Vogue
- Fietscomputer Wahoo
- Fietscomputer Walfort
- Fietscomputer XLC
- Fietscomputer O-Synce
- Fietscomputer Oregon Scientific
- Fietscomputer Osynce
- Fietscomputer Crivit
- Fietscomputer Steren
- Fietscomputer Kayoba
- Fietscomputer Cannondale
- Fietscomputer Cube
- Fietscomputer Conrad
- Fietscomputer Aplic
- Fietscomputer Blackburn
- Fietscomputer Lezyne
- Fietscomputer Cresta
- Fietscomputer Contec
- Fietscomputer BBB
- Fietscomputer Cateye
- Fietscomputer Axiom
- Fietscomputer Bell
- Fietscomputer Cordo
- Fietscomputer CicloSport
- Fietscomputer Dresco
- Fietscomputer Kellys
- Fietscomputer SmartHalo
- Fietscomputer Sunding
- Fietscomputer Wahoo Fitness
- Fietscomputer Magene
- Fietscomputer MCP
- Fietscomputer Ciclo
- Fietscomputer Stels
Nieuwste handleidingen voor Fietscomputer
15 November 2024
7 November 2024
23 September 2024
26 Juli 2024
26 Juli 2024
22 Juli 2024
16 Juli 2024
16 Juli 2024
15 Juli 2024
11 Juni 2024