TP Link LiteWave LS109P Handleiding

TP Link Niet gecategoriseerd LiteWave LS109P

Lees hieronder de 📖 handleiding in het Nederlandse voor TP Link LiteWave LS109P (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
Connection
Note: For simplicity, we will take LS106LP for example throughout this Guide.
Note:
1. PoE ports can also connect to non-PoE devices, but only transmit data.
2. LS105LP/ LS106LP can supply up to 30 W for each PoE port and 41 W for all PoE ports.
3. LS109P can supply up to 30 W for each PoE port and 63 W for all PoE ports.
4. LS109P has an uplink port (RJ45 port), which typically connects to uplink devices like routers.
IP Camera AP IP Phone
Router
LAN Port WAN Port
Internet
PoE Ports (1-4)
PoE Devices
Switches Explanation
Isolation (For LS109P)
O: Ports can transmit data with each other.
On: The corresponding ports cannot transmit data with other downlink ports. They can transmit data
only with the uplink port.
Extend (For LS105LP/LS106LP/LS109P)
O: The corresponding ports run at 10/100 Mbps and support PoE power supply up to 100 m away.
On: The corresponding ports run at 10 Mbps and support PoE power supply up to 250 m away.
Recovery (For LS105LP/LS106LP/LS109P)
O: The PoE Auto Recovery function is disabled.
On: The switch will constantly detect the working status of a PoE powered device (PD). When the switch
nds that the PD works abnormally, the switch will reboot it.
Note: The numbers in brackets indicate the ports where the feature takes eect. For example, when Extend (Port 1-4) is toggled to On, the Extend mode will be enabled for ports 1-4.
© 2024 TP-Link 7106510934 REV1.2.0
LED Explanation
Power PoE Status
On: Providing PoE power
Flashing: Current-overload/Short-circuit
O: Not providing PoE power
On: Power on
O: Power o
Link/Act; Uplink
On:
Running at 10/100 Mbps, but no activity.
Flashing:
Running at Mbps and is transmitting 10/100
or receiving data.
O:
No device is linked to the corresponding port.
PoE Max
For LS105LP/LS106LP:
On: 34 W≤Total power supply < 41 W
Flashing: Total power supply ≥ 41 W
O: Total power supply < 34 W
Installation Guide
10/100Mbps Desktop PoE+ Switch
LS105LP/LS106LP/LS109P
Power Adapter
Ethernet Ports (1-6)
For LS109P:
On: 56 W≤Total power supply < 63 W
Flashing: Total power supply ≥ 63 W
O: Total power supply < 56 W
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally. If the Power LED is
not lit, please try the following:
A1:
Make sure the AC power cord is connected to the switch with power source properly.
A2:
Make sure the voltage of the power supply meets the requirements of the input voltage
of the switch.
A3: Make sure the power source is on.
Q1. Why is the Power LED not lit?
It is recommended that you check the following items:
A1: Make sure that the cable connectors are rmly plugged into the switch and the device.
A2: Make sure the connected device is turned on and works normally.
A3: The cable must be less than 100 meters long (328 feet). If Extend Mode is enabled, it
should be less than 250 meters (820 feet).
Q2. Why is the Link/Act LED not lit while a device is connected to
the corresponding port?
Q3. Why are the PoE ports not supplying power for PoE devices?
When the total power consumption of connected PoE devices exceeds the maximum, the
PoE port with a smaller port number has higher priority. The system will cut o power to the
ports with larger port numbers to ensure supplying to other ports.
Take LS106LP as an example. If port 1, 2 and 4 are consuming 10 W respectively, and an
additional PoE device with 15 W is connected to port 3, the system will cut o the power of
port 4 to compensate for the overload.
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and
(EU)2015/863.
The original EU declaration of conformity may be found at
https://www.tp-link.com/en/support/ce/
EU declaration of conformity
UK declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and
Electrical Equipment (Safety) Regulations 2016.
The original UK declaration of conformity may be found at
https://www.tp-link.com/support/ukca
IEEE802.3i, IEEE802.3u, IEEE802.3x, IEEE802.3af,
IEEE802.3at
LS105LP:
5 10/100 Mbps RJ45 Ports
Auto-Negotiation MDI/MDIX
PoE Ports: Port 1-4
LS106LP:
6 10/100 Mbps RJ45 Ports
Auto-Negotiation MDI/MDIX
PoE Ports: Port 1-4
LS109P:
9 10/100 Mbps RJ45 Ports
Auto-Negotiation MDI/MDIX
PoE Ports: Port 1-8
10BASE-T: UTP category 3, 4, 5 cable (maximum 100 m);
EIA/TIA-568 100Ω STP (maximum 100 m)
100BASE-TX: UTP category 5, 5e cable (maximum 100 m);
EIA/TIA-568 100Ω STP (maximum 100 m)
LS105LP: 1 Gbps
LS106LP: 1.2 Gbps
LS109P: 1.8 Gbps
Store-and-Forward
Automatically learning, automatically aging
External Power Adapter
Input: 100-240 VAC, 50/60 Hz
Output:
53.5 VDC /0.81 A (LS105LP/LS106LP)
53.5 VDC /1.31 A (LS109P)
LS105LP/LS106LP: 41 W (up to 30 W for each PoE port)
LS109P: 63 W (up to 30 W for each PoE port)
Yes
LS105LP: 76 mm
LS106LP: 65mm
LS109P: 105mm
Standard
General Specications
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0 C to 40 C (32 F to 104 Ëš Ëš Ëš ËšF)
-40 C to 70 C (-40 F to 158 Ëš Ëš Ëš ËšF)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
Environmental and Physical Specications
Specications
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
To ask questions, find answers, and communicate with TP-Link
users or engineers, please visit https://community.tp-link.com
to join TP-Link Community.
Interface
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please
contact us.
Place the device with its bottom surface downward.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Network Media (Cable)
Switching Capacity
Power Supply
Transfer Method
MAC Address Learning
Wall Mountable
Distance Between
Mounting Holes
The plug on the power supply cord is used as the disconnect device, the
socket-outlet shall be easily accessible. (For LS109P)
A1: Before upgrading a connected PoE powered device (PD), disable PoE Auto Recovery to
avoid the PD’s damage.
A2: When a PD does not send data packets to the switch for a long period in certain
scenarios (e.g. an IPC in sleep mode), disable PoE Auto Recovery to avoid the PD
repeatedly rebooting.
Q4. What should I notice before using the PoE Auto Recovery
feature?
PoE Budget
The socket-outlet shall be installed near the equipment and shall be easily accessible. (For
LS109P)

Product specificaties

Merk: TP Link
Categorie: Niet gecategoriseerd
Model: LiteWave LS109P

Heb je hulp nodig?

Als je hulp nodig hebt met TP Link LiteWave LS109P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd TP Link

TP Link

TP Link TL-FC111A-20 Handleiding

11 December 2024
TP Link

TP Link TL-FC111B-20 Handleiding

10 December 2024
TP Link

TP Link Omada EAP650-Desktop Handleiding

10 December 2024
TP Link

TP Link Festa F54 Handleiding

10 December 2024
TP Link

TP Link Omada EAP673-Extender Handleiding

10 December 2024
TP Link

TP Link Archer TBE400E Handleiding

3 December 2024
TP Link

TP Link EAP653 UR Handleiding

12 November 2024
TP Link

TP Link LS1210P Handleiding

11 November 2024
TP Link

TP Link Archer TBE400UH Handleiding

11 November 2024
TP Link

TP Link Tapo P210 Handleiding

11 November 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx

Gourmetmaxx 03863 Handleiding

24 December 2024
Vello

Vello PGS-P Handleiding

24 December 2024
Venom

Venom Quad Charging Station VS4796 Handleiding

24 December 2024
Nec

Nec IPJ2000CM Handleiding

24 December 2024
Monogram

Monogram ZKPN Handleiding

24 December 2024
Philips

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024
Philips

Philips Senseo HD7002 Handleiding

24 December 2024
D-Link

D-Link DUB-C2 Handleiding

24 December 2024
Nec

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024
Nec

Nec DS1-TM01 Handleiding

24 December 2024