Tommee Tippee Perfect Prep Handleiding

Tommee Tippee Flessenbereiders Perfect Prep

Lees hieronder de 📖 handleiding in het Nederlandse voor Tommee Tippee Perfect Prep (4 pagina's) in de categorie Flessenbereiders. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

WATER

HOPPER

START / STOP

BUTTON

SETTING

DIAL

WARNING

LIGHTS

ACTION

BUTTONS

DISPENSER

OUTLET

DISPENSER

OUTLET

WATER

TANK

WATER

FILTER

BOTTLE

STAND

WARNING LIGHTS ACTION BUTTONS

CHANGE

FILTER CLEANING

MODE

FILTER

VOLUME

RESET

DE-CALC/

DE-SCALE

WATER TANK

HOT

WATER LEVEL

LOW

DE-CALC/

DE-SCALE

CLEANING

MODE

FOR DOMESTIC USE ONLY - NOT INTENDED FOR COMMERCIAL USE

NOTE: SET UP YOUR UNIT IN A COOL PLACE IN YOUR KITCHEN OUT OF DIRECT SUNLIGHT

perfect prep

machine

INSTRUCTIONS FOR USE

roclose naturet

1. SET UP AND

CLEANING

234

Place a container under the

dispenser outlet to capture the

water used to clean the system (at

least 1 litre capacity).

Plug in the unit, the tank empty

warning light will illuminate.

With the water hopper in place

(but not the filter) fill the hopper

with 1 litre of freshly boiled HOT

WATER -

Wait for the tank empty warning

light to go out. The water tank hot

light will illuminate.

5 6 7 8

Press the cleaning mode button and

hold for 2 seconds. The cleaning

mode light will illuminate.

Wait whilst the boiled water is

emptied from the tank, through the

dispenser, into the container that you

placed under the outlet in step 1.

The tank empty warning light will

illuminate once the water has

flushed through the system.

Discard the water captured in your

container and replace it under the

dispenser.

9a 9b 10 11

Remove the water hopper and

fit the filter*.

Replace in the water tank.

Fill the hopper with COLD WATER. Wait for the tank empty warning

light to go out.

Press the start/stop button. A red

light will flash.

13 14 15

The appliance will dispense an

amount of hot water.

Press the start/stop button again.

A green light will flash and an

amount of water will be dispensed

to finish the cycle.

Press the filter volume reset button

for 2 seconds to clear the memory.

Discard dispensed water.

Your system is now ready to use.

Before first use you need to run a cleaning cycle – which should take approximately 10 minutes. You should

clean your unit as part of the set up and again whenever you replace your filter. For hygiene and safety

reasons you should always clean your unit if it has been unused or in storage for longer than 2 weeks.

*Handling the filter cartridge by the top only:

• Remove the filter cartridge from packaging

• Remove sticker from the top of filter

• Fill a bowl with cold drinking water

• Fully submerge the cartridge in the water

• Gently agitate until the bubbles cease

FILTER

VOLUME

RESET

2. USAGE Before each use you must ensure that your water tank is above the minimum fill mark.

Water to fill the unit must come from the cold tap.

Check the water level and top up if

necessary with COLD WATER. When

filling the tank, you must always fill the

hopper and as the water passes through

the filter you can regularly top it up.

Turn the dial to select the feed

size you require (120ml – 330ml).

Position your sterilised bottle

under the dispenser. Adjust bottle

stand if necessary. (Bottle neck

should sit close to the outlet).

Press the start/stop button. A red

light will flash and a volume of

HOT WATER is dispensed into

your bottle.

4 5

The light will change to solid red

and there will be a double beep

to indicate the end of the first

stage. You will need to make up

your feed within 2 minutes.

Carefully remove the bottle from

the stand and measure the

correct number of formula

scoops into the bottle.

6 7

Screw the sterilised milk storage

lid onto the bottle and ensure

that the lid is tight. Be careful

when handling hot liquid.

Shake well until the formula

powder has dissolved.

8 9

Remove the milk storage lid and

replace your bottle onto the

bottle stand.

10 11

Always check that the amount

dispensed is consistent with the

size of feed you have selected on

the dial. Add the sterilised teat,

screw ring and hood and shake.

12 13

For your child’s safety always

check food temperature before

feeding by testing on a sensitive

part of your skin.

Your bottle is now ready to serve.

Make sure you discard any

unwanted feed as per the formula

manufacturers recommendation.

Press the start/stop button again.

The red light will go out and the

green light will flash. If this button

is not pressed within 2 minutes of

the hot water being dispensed a

long beep will sound. If the alarm

sounds you should discard the feed

and repeat the process from step 1.

Wait whilst the remainder of

water is dispensed. Once

completed, there will be a

double beep and the green

light will change to solid.

If at any point you need to stop the perfect prep™ machine you can

do so by pressing the start/stop button. The pump may continue to

run for a few seconds and the green light will illuminate to show that

the process has ended. It will not be possible to restart the machine

for 20 seconds. Should you have to stop the perfect prep™ machine

please discard of any feed.

HOW TO STOP THE PERFECT PREP™ MACHINE

For a cool tank keep the unit out of direct sunlight and away from

sources of heat. Fill with COLD WATER from the fridge. Regularly top

up with COLD/COOLED WATER.

HINTS AND TIPS

Product specificaties

Merk:	Tommee Tippee
Categorie:	Flessenbereiders
Model:	Perfect Prep
Soort bediening:	Knoppen
Kleur van het product:	Zwart
Materiaal behuizing:	Kunststof
Aanbevolen leeftijd (max):	- maand(en)
Aanbevolen leeftijd (min):	- maand(en)
Type stroombron:	AC
Gebruiksvriendelijk:	Ja
Inhoud:	- l
Opwarmtijd:	2 min
Draagbaar:	Nee
Snelle opwarming:	Ja