Toa SR-WB4 Handleiding

Toa Niet gecategoriseerd SR-WB4

Lees hieronder de 📖 handleiding in het Nederlandse voor Toa SR-WB4 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Printed in Japan

133-01-439-60

Bracket base: 2 pieces

(component of the SR-WB4)

Speaker mounting bracket (A) (component of the SR-WB4)

Speaker mounting bracket (B)

(component of the SR-WB4)

Speaker mounting bracket (B)

(component of the SR-WB4)

Hexagon head bolt M8 x 20

(supplied with the SR-WB4)

Hexagon head bolt M5 x 20

(4 each of upper and lower

parts on both sides of speaker)

Screw slot

Remove the 16 attached screws (in upper and lower parts on both sides of speaker).

Note

The removed screws are not used.

Speaker

4, 7

Attach the speaker mounting bracket (A)

to the lower part of the speaker.

[When facing the speaker toward the right]

[When facing the speaker toward the left]

Hexagon head bolt M8 x 20

(supplied with the SR-WB4)

Allow the space for inserting

the bracket base.

INSTALLATION MANUAL

WALL TILT BRACKET SR-WB4

The SR-WB4 is designed to be used exclusively to mount the

SR-S4L Line Array Speaker on a wall. It allows the speaker

orientation angle to be adjusted to 30° max. vertically. Using the

optional SR-EP4 Extension Plate, it can joint up to 2 speakers.

Since the bracket is designed for indoor use, do not install it

outdoors.

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the

instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section,

which contain important warnings and/or cautions regarding

safety.

• After reading, keep this manual handy for future reference.

4. SPECIFICATIONS

• Accessories

Hexagon head bolt M8 x 20 (with washer) ........... 8

Hexagon head bolt M5 x 20 (with washer) ......... 16

• Option

Extension plate: SR-EP4

Note: The design and specifications are subject to change without

notice for improvement.

Step 1. Fix the bracket base on a

wall.

Mounting pitch differs

depending on whether 1 or

2 speakers are mounted.

2. INSTALLATION

Extension Plate

SR-EP4 (optional)

• Refer all installation work to the dealer from whom the unit was

purchased. Installation requires extensive technical knowledge

and experience. The speaker may fall off if incorrectly installed,

resulting in possible personal injury.

• Install the unit only in a location that can structurally support the

weight of the unit and the speaker. Doing otherwise may result in

the speaker falling down and causing personal injury and/or

property damage.

• Owing to the speaker's size and weight, be sure that at least two

persons are available to install the speaker. Failure to do so

could result in personal injury.

• Do not use other methods than specified to mount the bracket.

Extreme force is applied to the unit and the speaker could fall off,

possibly resulting in personal injuries.

• Use nuts and bolts that are appropriate for the wall's structure

and composition. Failure to do so may cause the speaker to fall,

resulting in material damage and possible personal injury.

• Tighten each nut and bolt securely. Ensure that the bracket has

no loose joints after installation to prevent accidents that could

result in personal injury.

• Do not mount the unit in locations exposed to constant vibration.

The mounting bracket can be damaged by excessive vibration,

potentially causing the speaker to fall, which could result in

personal injury.

Indicates a potentially hazardous situation which, if mishandled,

could result in death or serious personal injury.

WARNING

Indicates a potentially hazardous situation which, if mishandled, could

result in moderate or minor personal injury, and/or property damage.

CAUTION

• Avoid touching the unit's sharp metal edge to prevent injury.

• Do not stand or sit on, nor hang down from the unit as this may

cause it to fall down or drop, resulting in personal injury and/or

property damage.

• Have the unit checked periodically by the shop from where it was

purchased. Failure to do so may result in corrosion or damage to

the unit that could cause the unit to fall, possibly causing

personal injury.

Step 2. Remove the screws on both

sides of the speaker.

When jointing 2 speakers,

use the optional SR-EP4

Extension Plate.

For speaker joint, refer to the

instruction manual enclosed

with the SR-S4L Line Array

speaker.

Note

Up to 2 speakers can be joined and mounted. Never

join more than 2 speakers.

Step 3. Attach the speaker mounting bracket (A) and (B) to

the speaker.

When facing the speaker toward the right, attach

Bracket (A) to the upper part of the speaker and

Bracket (B) to the lower part. Conversely, when facing

the speaker toward the left, attach Bracket (B) to the

upper part and Bracket (A) to the lower part.

Step 4. Fix the hexagon head bolts (1 each on both sides of

upper and lower brackets) loosely to the speaker

mounting bracket.

Step 5. Connect a speaker cable to the speaker.

Step 6. Insert the loosely fitted bolts into the bracket base's

screw slots.

Step 7. Tighten the hexagon head bolts (1 each on both sides

of upper and lower brackets) to securely fix the

speaker brackets.

At the same time tighten 4 loosely fixed bolts in step 4.

Bolts and nuts used to fix a

bracket base on a wall are not

included. Use bolts and nuts

that are appropriate for the

construction of wall.

WARNING

Bracket base

Speaker

160

1855734 (1630)

895 (1791)

33 55

12 x 17

Unit: mm

[Wall mounting dimensions]

Loosen the angle adjustment bolts of the speaker brackets to

determine the speaker orientation.

The speaker brackets are marked in 5 for angle reference°

purposes.

3. ADJUSTING THE SPEAKER ORIENTATION

Speaker mounting bracket (A)

Horizontal facing angle

Maximum 30°

[When facing the speaker toward the right]

Angle adjustment bolt

(2 each of upper and

lower brackets)

[Finished assembly view]

Note

Tighten the loosely fixed

bolts after finishing angle

adjustment.

Number of Speakers Max. 2 (when jointed with an optional

to be Mounted SR-EP4)

Finish Steel plate, white, paint

Weight 4.6 kg (including accessories)

Product Composition Speaker mounting bracket A ...... 1,

Speaker mounting bracket B ...... 1,

Bracket base ...... 2

Product specificaties

Merk:	Toa
Categorie:	Niet gecategoriseerd
Model:	SR-WB4
Kleur van het product:	Wit
Gewicht:	4600 g
Plaatsing:	Muur
Montagewijze:	Muur
Materiaal:	Staal
Compatibiliteit:	SR-S4L