Toa HY-CW1B Handleiding

Toa Niet gecategoriseerd HY-CW1B

Lees hieronder de 📖 handleiding in het Nederlandse voor Toa HY-CW1B (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 197 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Printed in Indonesia

5 3 3 - 0 6 - 1 1 9 - 6 0

HX-5 series'

rear plate

(2 63/ )64

17°

10°

184 (7 1/ )4

R99.5

(R3 59/64)

(15

/32)

[Mounting dimensions]

Unit: mm (inches)

Note

If the HX-5 series is installed vertically,

change the orientation of the rear plate.

More particularly, refer to the instruction

manual supplied with the HX-5 series.

Nut B

Nut A

Speaker

bracket bolt

Ceiling bracket

Speaker bracket bolt

(Insert the speaker bracket bolt through

the slot in the ceiling bracket.)

Vertical angle

adjustment bolt

Vertical angle

adjustment bolt

Angle adjustment hole

90 (7.5 x 12)° °

Axis bolt, Axis nut

Speaker bracket

Hexagon head bolt

M8 x 15 with washer

(supplied with the

HY-CW1 series)

INSTALLATION MANUAL

SPEAKER MOUNTING BRACKETS

HY-CW1B

HY-CW1W

HY-CW1WP

TOA's HY-CW1B, HY-CW1W and HY-CW1WP are designed to be

used exclusively to mount the HX-5 series speaker system to a

ceiling.

Both the HY-CW1B and the HY-CW1W are designed for indoor

use, while the HY-CW1WP is designed for outdoor use.

The speaker can be rotated 360° horizontally. It can also be tilted

vertically up to 82.5° when suspended horizontally, and depending

on the speaker directivity mode, up to 67.5° (for 60° mode) or 75°

(for 15°, 30° or 45° mode) when suspended vertically.

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the

instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section,

which contain important warnings and/or cautions regarding

safety.

• After reading, keep this manual handy for future reference.

6. SPECIFICATIONS

• Accessories

Hexagon head bolt M8 x 15 (with washer) ........ 4

Note: The design and specifications are subject to change without

notice for improvement.

• Install the unit only in a location that can structurally support the

weight of the unit and the speaker. Doing otherwise may result in

the speaker falling down and causing personal injury and/or

property damage.

• (HY-CW1B and HY-CW1W only)

Since the unit is designed for indoor use, do not install it

outdoors. If installed outdoors, the aging of parts causes the unit

to fall off, resulting in personal injury.

• Owing to the speaker's size and weight, be sure that at least two

persons are available to install the speaker. Failure to do so

could result in personal injury.

• Do not use other methods than specified to mount the bracket.

Extreme force is applied to the unit and the speaker could fall off,

possibly resulting in personal injuries.

• Use nuts and bolts that are appropriate for the ceiling structure

and composition. Failure to do so may cause the speaker to fall,

resulting in material damage and possible personal injury.

• Tighten each nut and bolt securely. Ensure that the bracket has

no loose joints after installation to prevent accidents that could

result in personal injury.

• Use the specified speaker in combination. Doing otherwise may

cause the speaker to fall off, resulting in personal injury.

• Do not mount the unit in locations exposed to constant vibration.

The mounting bracket can be damaged by excessive vibration,

potentially causing the speaker to fall, which could result in

personal injury.

• Avoid installing the speaker in locations close to the seashore or

in indoor swimming facilities that are not well ventilated. In such

locations the bracket may be vulnerable to corrosion, eventually

allowing the speaker to fall resulting in personal injury.

Indicates a potentially hazardous situation which, if mishandled,

could result in death or serious personal injury.

WARNING

Indicates a potentially hazardous situation which, if mishandled, could

result in moderate or minor personal injury, and/or property damage.

CAUTION

• Avoid touching the unit's sharp metal edge to prevent injury.

• Do not hang down from the unit as this may cause it to fall down

or drop, resulting in personal injury and/or property damage.

• Have the unit checked periodically by the shop from where it was

purchased. Failure to do so may result in corrosion or damage to

the unit that could cause the unit to fall, possibly causing

personal injury.

Step 4. Use the hex head bolts to attach the speaker bracket

to the HX-5 series' rear plate.

Step 5. Lift the speaker and insert the speaker bracket bolt

through the slot in the ceiling bracket.

Step 6. Fix the HX-5 series in the desired horizontal

orientation and tighten nuts A and B.

Only loosen the axis bolt and axis nut; do not remove them

as doing so may cause the speaker to fall, resulting in

personal injury.

WARNING

Only the HY-CW1WP can be installed outdoors.

• Only the HX-5B-WP and HX-5W-WP speakers can be

installed outdoors.

• Install the speaker so that all speaker modules face

downward from the horizontal axis. Doing otherwise could

adversely affect the speaker's weather resistance and

possibly lead to malfunction or failure.

2. PRECAUTIONS WHEN INSTALLING THE

HY-CW1WP

Step 1. Mount the ceiling bracket to a ceiling.

Note

Anchor bolts, nuts, and washers required for mounting

are not supplied with the bracket.

Step 2. Turn nut A fully to the root of the speaker bracket bolt.

Step 3. Remove the vertical angle adjustment bolts (one each

for left and right) and loosen the axis bolt and axis nut.

3. INSTALLATION

Step 7. With the HX-5 series' vertical orientation set to the

desired position, fix the vertical angle adjustment

bolts (one each for left and right) to the speaker

bracket.

Step 8. Retighten the axis bolt and axis nut.

Tighten nut B so that the bolt head projects at least 3 mm

(1/8") from the nut. Doing otherwise could allow the speaker

to fall, resulting in personal injury.

WARNING

5. FINISHED ASSEMBLY DIAGRAM

HX-5 series

[When suspended vertically] [When suspended horizontally]

HY-CW1

series

82.5°

67.5°

HY-CW1B HY-CW1W HY-CW1WP

Steel plate, black, Steel plate, white, Stainless steel

semi-gloss, paint semi-gloss, paint (SUS304)

120 (w) x 200 (h) x 220 (d) mm

4 23/

32 (w) x 7 7

/8(h) x 8 21/32 (d) inches

2 kg

Model No.

Finish

Dimensions

Weight

Product specificaties

Merk:	Toa
Categorie:	Niet gecategoriseerd
Model:	HY-CW1B
Kleur van het product:	Zwart
Gewicht:	2000 g
Breedte:	120 mm
Diepte:	220 mm
Hoogte (max):	200 mm
Plaatsing:	Plafond
Materiaal:	Staal
Inclusief bouten:	Ja