Toa HY-CN1W Handleiding

Toa Niet gecategoriseerd HY-CN1W

Lees hieronder de 📖 handleiding in het Nederlandse voor Toa HY-CN1W (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
TOA's HY-CN1 series brackets are used to join 2 HX-5 series speaker systems, typically for the purpose of achieving
better speaker directivity control in lower frequencies. Such directivity control helps achieve clearer and longer-range
sound reproduction in locations where sound efficiency may be hampered by conditions like long reverberation time or a
high level of background noise.
HY-CN1B, HY-CN1W,
HY-CN1B-WP, HY-CN1W-WP
SPEAKER EXTENSION BRACKETS
INSTALLATION MANUAL
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the
instructions in this section for correct and safe operation.
• Be sure to follow all the precautionary instructions in this
section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future
reference.
• Install the unit only in a location that can structurally
support the weight of the unit and the speaker. Doing
otherwise may result in the speaker falling down and
causing personal injury and/or property damage.
• (HY-CN1B and HY-CN1W only)
Since the unit is designed for indoor use, do not install it
outdoors. If installed outdoors, the aging of parts causes
the unit to fall off, resulting in personal injury.
• Do not use other methods than specified to mount the
unit. Extreme force is applied to the unit and the speaker
could fall off, possibly resulting in personal injuries.
• Tighten each nut and bolt securely. Ensure that the unit
has no loose joints after installation to prevent accidents
that could result in personal injury.
• Use the specified speaker in combination. Doing
otherwise may cause the speaker to fall off, resulting in
personal injury.
• Do not mount the unit in locations exposed to constant
vibration. The unit can be damaged by excessive
vibration, potentially causing the speaker to fall, which
could result in personal injury.
• Avoid installing the speaker in locations close to the
seashore or in indoor swimming facilities that are not well
ventilated. In such locations the unit may be vulnerable to
corrosion, eventually allowing the speaker to fall resulting
in personal injury.
2. PRECAUTIONS WHEN INSTALLING
THE HY-CN1B-WP AND HY-CN1W-WP
Only the HY-CN1B-WP and HY-CN1W-WP can be
installed outdoors.
• Only the HX-5B-WP and HX-5W-WP speaker systems
can be installed outdoors.
• Install the speaker so that all speaker modules face
downward from the horizontal axis.
Doing otherwise could adversely affect the speaker's
weather resistance and possibly lead to malfunction or
failure.
3. FINISHED ASSEMBLY DIAGRAM
Unit: mm (inches)
Indicates a potentially hazardous situation which, if
mishandled, could result in death or serious personal
injury.
WARNING
Indicates a potentially hazardous situation which, if
mishandled, could result in moderate or minor personal injury,
and/or property damage.
CAUTION
• Avoid touching the unit's sharp metal edge to prevent
injury.
• Have the unit checked periodically by the shop from
where it was purchased. Failure to do so may result in
corrosion or damage to the unit that could cause the unit
to fall, possibly causing personal injury.
Front bar bracket
(component of HY-CN1 series)
Rear bar bracket
(component of HY-CN1 series)
HX-5series
HX-5 series
(When set to the 60 mode) (When set to the 15 mode)° °
1090 (42 29/32) 1104 (43 –15/32)
4. SPEAKER EXTENSION
[Before joining HX-5 series...]
Step 1. Remove the front grill from the speaker module of each HX-5 series by unscrewing 4 bolts with the supplied hex
head wrench.
Step 2. Remove the front end bars from each module by unscrewing 4 bolts.
1
2
Front grill
Speaker module
Note: Use these bolts in step 4.
Note: Use these bolts in step 3.
Front end bar
HX-5 series
A
HX-5 series
B
[Joining HX-5 series]
Set the speakers on their sides, handles facing up.
Step 3. Join the HX-5 series and using the front bar brackets.
Use the removed bolts in Step 2 to attach the front bar brackets.
BA
Bolts can be tightened using either a Phillips screwdriver or a wrench, but be sure to finish the tightening with the
wrench to ensure optimum tightness. Doing otherwise may result in the speaker falling down and causing personal
injury and/or property damage.
WARNING
Step 4. Reattach the front grills to the speaker modules.
Retighten the bolts using the supplied hex head wrench, making sure that the edges the grills remain securely
fitted into their receptacle slots.
Step 5. Attach the rear bar bracket.
Note
When joining 2 HX-5 series that are both set to the 15 mode, also position the bolts on the rear bar bracket to°
the 15 mode, thus permitting a total of 30 of continuous joined directivity. ° °
15 mode°
30 mode°
45 mode°
60 mode°
3
4
5
Front bar bracket mounting position
Rear bar bracket mounting position
Rear bar bracket
Fix the directivity mode at the desired angle.
Rear bar bracket
(component of
HY-CN1 series)
Handle
Front bar bracket
(component of HY-CN1 series)
Front grill
Removed bolts in Step 1
Removed bolts in Step 2
Front bar bracket
Fix the bracket using
the bolts attached to
the speaker system.
HX-5 series
A
HX-5 series
A
HX-5 series
B
HX-5 series
's bar
's bar
B

Product specificaties

Merk: Toa
Categorie: Niet gecategoriseerd
Model: HY-CN1W

Heb je hulp nodig?

Als je hulp nodig hebt met Toa HY-CN1W stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Toa

Toa

Toa ST-34B Handleiding

18 September 2024
Toa

Toa PJ-304 Handleiding

3 September 2024
Toa

Toa PE-604 Handleiding

3 September 2024
Toa

Toa SC-630TU Handleiding

9 Juli 2024
Toa

Toa SR-SA4 Handleiding

9 Juli 2024
Toa

Toa ST-800 Handleiding

9 Juli 2024
Toa

Toa HY-C0801W Handleiding

22 Juni 2024
Toa

Toa SR-RF12 Handleiding

13 Maart 2024
Toa

Toa HY-C0801 Handleiding

13 Maart 2024
Toa

Toa HY-TM7B-WP Handleiding

12 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024