Toa HY-60DB-WP-3 Handleiding

Toa Niet gecategoriseerd HY-60DB-WP-3

Lees hieronder de 📖 handleiding in het Nederlandse voor Toa HY-60DB-WP-3 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

INSTALLATION MANUAL

ANGLE ADJUSTMENT BRACKETS

HY-60DB, HY-60DW, HY-60DB-WP, HY-60DW-WP

Thank you for purchasing TOA’s Angle Adjustment Bracket.

Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

1. SAFETY PRECAUTIONS

• Beforeinstallationoruse,besuretocarefullyread

all the instructions in this section for correct and

safe operation.

• Besuretofollowalltheprecautionaryinstructions

in this section, which contain important warnings

and/or cautions regarding safety.

• After reading, keep this manual handy for future

reference.

• (HY-60DBandHY-60DWonly)

Since the bracket is designed for indoor use, do not

install it outdoors. If installed outdoors, the aging

of parts causes the speaker to fall off, resulting in

personal injury. Also, when it gets wet with rain,

there is a danger of electric shock.

• Donotuseothermethodsthanspeciedtomount

the bracket. Extreme force is applied to the speaker

and it could fall off, possibly resulting in personal

injuries.

• Tighten each nut and bolt securely. Ensure that

the bracket has no loose joints after installation

to prevent accidents that could result in personal

injury.

• UsethespeciedSpeakerSystemincombination.

Doing otherwise may cause the speaker or

component to fall off, resulting in personal injury.

• Avoidinstallingthespeakerinlocationsclosetothe

seashore or in indoor swimming facilities that are

not well ventilated. In such locations, the bracket

may be vulnerable to corrosion, eventually allowing

the speaker to fall resulting in personal injury.

• Avoid touching the bracket’s sharp metal edge to

prevent injury.

• Havethebracketcheckedperiodicallybytheshop

from where it was purchased. Failure to do so may

result in corrosion or damage to the bracket that

could cause the speaker to fall, possibly causing

personal injury.

Indicates a potentially hazardous situation which,

if mishandled, could result in death or serious

personal injury.

WARNING

Indicates a potentially hazardous situation which,

if mishandled, could result in moderate or minor

personal injury, and/or property damage.

CAUTION

2. GENERAL DESCRIPTION

TOA’sHY-60DSeriesBracketsareusedtochangethedirectivityanglemode

ofHX-7SeriesSpeaker System to60°mode.Three piecesoftheHY-60D

Seriesarerequiredtoobtain60°modeofdirectivityangle.

Both HY-60DB and HY-60DW brackets are designed for indoor use only.

The HY-60DB-WPand HY-60DW-WPbrackets can be used outdoors, but

only under eaves or in other locations not directly exposed to rain and the

elements.

Usethesebracketsincombinationwiththespeakersystemsshownatright.

3. SPECIFICATIONS

Model No. HY-60DB HY-60DW HY-60D-WP HY-60W-WP

Finish Steel plate, black,

semi-gloss, paint

Steel plate, white,

semi-gloss, paint

Stainless plate, black,

semi-gloss, paint

Stainless plate, white,

semi-gloss, paint

Dimensions 102.2x26.2mm(4.02"x1.03"),t=4.5mm(0.18"),withø9.4mm(0.37")andø6.4mm(0.25")holes

Weight 70g(0.15lb)

Note: Thedesignandspecicationsaresubjecttochangewithoutnoticeforimprovement.

Speaker System Angle Adjustment Bracket

HX-7B HY-60DB

HX-7W HY-60DW

HX-7B-WP HY-60DB-WP

HX-7W-WP HY-60DW-WP

URL:http://www.toa.jp/

133-01-00039-00

4. CHANGING TO 60° MODE

Tighten the bolts securely, as instructed below.

Failure to follow instructions precisely could result in a falling speaker

and potential personal injury.

• Ensurethatallboltsaresecurelyinsertedasfarastheirthreadsgo,

then securely fasten each bolt with a nut.

• Tightenalltheboltswiththedesignatedtighteningtorque.

For tightening, use a Phillips screwdriver, or open- or box-end wrench.

WARNING

Beforechanginganglemodes,layoutaprotectivesheet,corrugatedcardboardorothersoftmaterialonaatsurface,

andperformallworkonthespeakerwithitsfrontbafefacingdownward.Asthespeakerassemblyisquiteheavy,itis

recommendedthatatleasttwopersonsbeinvolvedinthemodicationwork.Asanexample,theHX-7Seriesspeaker

showninthegurebelowisarrangedinadirectionthatexposesthespeaker’sleft-sideprotectioncovers.

Step 1. Detachallrearanglebarsfromthespeaker.

Removethenutsandboltsfrombothendsoftherearanglebars.Also

carefullyremovethespacerttedintothelargerholeineachanglebar.

Note

Take care not to lose the removed nuts, bolts and spacers, as they will be

used again in reassembly.

Step 2. Fit the spacers into the larger holes in these brackets, and attach each

bracket by inserting a bolt into the position where the rear angle bar was

mounted. Then fasten each bolt with a nut.

Note

This position will become the fulcrum for the angle adjustment. Be sure

to attach in the illustrated position. If attached in a different position, the

anglemodewillnotassumethespeciedmode.

Step 3. Align the other side of each bracket with the 60° mode position, then

insert a bolt and fasten the bolt with a nut.

Rear angle bar

Spacer

Bolt

Nut

Detach

Protection cover HX-7 Series speaker

This bracket

Nut removed in .Step 1

[Completed Assembly]

60° mode position

Protection cover

HX-7 Series speaker

Spacer removed

in .Step 1

Bolt removed

in .Step 1

Fulcrum for the angle

adjustment

Tightening torque:

3 N·m

Angle adjustment holes

Rear bracket

30° mode

15° mode

45° mode

60° mode

Tip

Notethatthespeakercanbesetto15°,30°,or45°

mode using these brackets. When selecting any

other than 60° mode, attach each bracket to the

hole corresponding to the desired directivity angle

mode,referringtothegurebelow:

Product specificaties

Merk:	Toa
Categorie:	Niet gecategoriseerd
Model:	HY-60DB-WP-3

Heb je hulp nodig?

Als je hulp nodig hebt met Toa HY-60DB-WP-3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Toa

Toa ST-34B Handleiding

18 September 2024

Toa PJ-304 Handleiding

3 September 2024

Toa PE-604 Handleiding

3 September 2024

Toa SC-630TU Handleiding

9 Juli 2024

Toa SR-SA4 Handleiding

9 Juli 2024

Toa ST-800 Handleiding

9 Juli 2024

Toa HY-C0801W Handleiding

22 Juni 2024

Toa SR-RF12 Handleiding

13 Maart 2024

Toa HY-C0801 Handleiding

13 Maart 2024

Toa HY-TM7B-WP Handleiding

12 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024