Toa AN9001 Handleiding

Toa Controller AN9001

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Toa AN9001 (2 pagina's) in de categorie Controller. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
CEILING MOUNT MICROPHONE
OPERATING INSTRUCTIONS
AN-9001
Thank you for purchasing TOA's Ceiling Mount Microphone.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of
your equipment.
1. GENERAL DESCRIPTION
The AN-9001 is an electret condenser microphone designed for ambient noise
detection. It is used in conjunction with the AN-001T Ambient Noise Sensor
Input module in the 9000 Series system. It can be mounted in a 1-gang
electrical box (American type) in the ceiling or wall.
2. DIMENSIONAL DIAGRAM
Lock
Release
Hot Cold Earth
31
37
70
ΓΈ130
70
70
83.5
104
83.5
90 – 98
46 – 50
42
38
[Front] [Side] [Rear]
[Bottom]
[Front view of Main unit] [Figure when mounted]
[Dimensions of
mounting opening]
1-gang electorical box
(American type, not supplied)
Unit: mm
Microphone output terminal
[Hot, Cold, Earth]
Electronically-balanced 3P removable
terminal block.
Sensitivity: –5 dB (1 kHz, 0 dB = 1 V/Pa)
Output impedance: 200 Ξ©
4. INSTALLATION
Step 1. Install a 1-gang electrical box in a wall or ceiling.
Step 2. Mount the AN-9001's Main unit to the installed electrical box.
Use the 2 screws (No.6-32UNC x 30) supplied with the AN-9001.
Note
The AN-9001 comes with 2 types of machine screws: No.6-32UNC x 30
(unified threads) and M4 x 30 (metric threads). Be sure to use correct
ones.
Step 3. Let both detents on the panel's rear into the detent insertion openings of
the Main unit.
Tips
For detent insertion, refer to the following points:
(A) Align 2 triangular marks on the panel with the extended line
connecting between Main unit's mounting screws.
(B) Align the panel's center hole with the Main unit's microphone.
Step 4. Rotate the panel clockwise.
The panel locks into place by rotating it about 20Β° in the "Lock" direction.
2
3
A
B
Panel's rear
AN-9001's Main unit
Machine screw
No.6-32UNC x 30 (2 places)Detent (2 places)
Microphone
Detent insertion
opening (2 places)
3. CONNECTION
The AN-001T and AN-9001 are connected as illustrated below and used to
control the speaker sound volume in a room or such closed space.
9000 Series system
Note
Keep the AN-9001 as distant as possible from a sound source
(speaker, water supply pipe, or air conditioning).
If installed close to a sound source, the AN-9001 could sense it
as ambient noise to control the speaker sound volume.
SP OUT
AN-001T
Speaker AN-9001
5. REMOVABLE TERMINAL PLUG CONNECTION
Be sure to use the supplied removable terminal plugs for connections to the
removable terminal blocks.
Notes
β€’ Be sure to use shielded cables for audio signal lines.
β€’ Avoid soldering stranded or shielded cable, as contact resistance may
increase when the cable is tightened and the solder is crushed, possibly
resulting in an excessive rise in joint temperatures.
[Cable end treatment]
7 mm 7 mm
20 mm
Solid or stranded cable Shielded cable
[Connector connection ]
Step 1. Loosen the terminal screw, then
insert the cable.
Step 2. Retighten the terminal screw.
(Pull on the cable to ensure it is
securely connected.)
Tip
Recommended slotted screwdriver type:
Screwdriver with 3 mm blade width
Tightens Loosens
Terminal screw
Slotted screwdriver
Shielded cable
1
2
Removable terminal plug
(accessory)
1
Bit shape 3 mm
Electret condenser microphone
14 – 26 V DC
7 mA (at 24 V DC)
Omnidirectional (hemispherical)
200 Ξ©
–5 dB (1 kHz, 0 dB = 1 V/Pa)
100 – 10,000 Hz
Removable terminal block (3 pins)
–10 to +40Β°C
Panel: ABS resin, white
Frame, Case: Surface-treated steel plate
ΓΈ130 x 37 (d) mm
170 g
Type
Phantom Power
Current Consumption
Directivity
Impedance
Rated Sensitivity
Frequency Response
Output Terminal
Operating Temperature
Finish
Dimensions
Weight
6. SPECIFICATIONS
Note: The design and specifications are subject to change without notice for improvement.
β€’ Accessories
Removable terminal plug (3 pins) .............. 1
Machine screw No. 6-32 UNC x 30 ............ 2
Machine screw M4 x 30 ............................. 2
Traceability Information for Europe (EMC directive 2004/108/EC)
Manufacturer:
TOA Corporation
7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe,
Hyogo, Japan
Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg,
Germany
133-05-399-9B
URL: http://www.toa.jp/

Product specificaties

Merk: Toa
Categorie: Controller
Model: AN9001

Heb je hulp nodig?

Als je hulp nodig hebt met Toa AN9001 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Controller Toa

Toa

Toa ZM-9012 Handleiding

4 Mei 2023
Toa

Toa WP-700-AM Handleiding

20 April 2023
Toa

Toa AT-100 Handleiding

4 April 2023
Toa

Toa AT-100EMG Handleiding

13 Maart 2023
Toa

Toa ZM-9013 Handleiding

18 Februari 2023
Toa

Toa ZM-9003 Handleiding

8 Februari 2023
Toa

Toa AT-025 Handleiding

14 Januari 2023
Toa

Toa AN9001 Handleiding

7 Januari 2023
Toa

Toa SS-9001PS Handleiding

6 December 2022

Handleiding Controller

Nieuwste handleidingen voor Controller

IVT

IVT SCDplus Handleiding

11 December 2024
IVT

IVT MPPTplus+ 20A Handleiding

10 December 2024
GVM

GVM YK22 Handleiding

10 December 2024
Alfatron

Alfatron ALF-IPCON-HDMI Handleiding

10 December 2024
Harvia

Harvia Xenio C260 Handleiding

8 December 2024
Hotone

Hotone Patch Kommander Handleiding

7 December 2024
Hotone

Hotone Ampero Control Handleiding

7 December 2024
IFM

IFM AC1317 Handleiding

5 December 2024
Speed-Link

Speed-Link Thunderstrike Handleiding

2 December 2024
COLBOR

COLBOR CTRL1 Handleiding

29 November 2024