Teledex Opal 1010S Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Teledex Opal 1010S (3 pagina's) in de categorie Telefoon. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/3
CONNECTING THE OPAL 1010S
Included with the Opal 1010S are (one each):
• Base unit • Coiled handset cord • User guide
• Handset • Clear plastic overlay • Line cord
Contact your supplier or Teledex for information on ordering
custom designed and printed faceplates to enhance the look of your
Teledex telephone.
1) Located on the left side of the Opal 1010S (as the phone is fac-
ing you) is a modular jack. Insert one end of the coiled handset
cord into this jack (you should hear the coil cord click when
properly inserted).
2) Insert the other end of the coiled handset cord into the modular
jack on the handset.
3) Turn the telephone so the back panel is facing you. Insert either
end of the line cord into the jack on the back of the telephone
labeled LINE.
4) Insert the other end of the line cord into a telephone wall outlet
jack.
5) Once your telephone is connected, remove the plastic overlay
and place the paper faceplate over the keys. Replace the plastic
overlay by hooking the tabs on the overlay into the recessed
slots located on both sides. The overlay is easiest to insert when;
the left or right side tabs are inserted first, and the middle of the
overlay is slightly bowed to allow for insertion of the other tabs.
PLACING A CALL
USING THE HANDSET:
1) Lift the handset.
2) Listen for dial tone, dial the desired number, or press an AUTO
DIAL key to automatically dial a number.
3) To end the call, hang up by placing the handset back in the cradle.
USING THE SPEAKERPHONE:
1) With the handset in the cradle, press the SPEAKER key. The
Opal will engage the open line.
NOTE: The red SPEAKER LED will indicate that the speaker-
phone is active.
2) Listen for dial tone. Dial the desired number, or press an AUTO
DIAL key to automatically dial a number.
3) To end call the call press the SPEAKER key again.
RECEIVING A CALL
An audible ring and flickering red LED indicate an inbound call.
USING THE HANDSET:
1) Lift the handset. The Opal will select the ringing line.
2) To end the call hang up the handset.
USING THE SPEAKERPHONE:
With the handset in the cradle, press the
SPEAKER key. The Opal
will select the ringing line and answer with the speakerphone active.
Note: The red SPEAKER LED will indicate that the speakerphone is
active.
ADJUSTING SPEAKERPHONE VOLUME
Locate the slide switch (labeled ) on the right side of theSPKR VOL
telephone. To increase speaker volume, slide the switch towards the
back of the telephone. To decrease speaker volume, slide the switch
towards the front of the telephone.
ADJUSTING THE RING VOLUME
Locate the adjustment control on the back of the telephone labeled
RINGER LOW/HI (see diagram). Slide the switch to the desired LOW
or HI ring volume.
SPEAKERPHONE TIPS
TO ACTIVATE THE HANDSET FROM SPEAKERPHONE
MODE:
1) Lift the handset from the cradle.
2) The red SPEAKER LED will go out.
TO ACTIVATE THE SPEAKERPHONE FROM HANDSET
MODE:
1) Press the SPEAKER key.
2) The red SPEAKER LED will indicate speakerphone selection.
3) Place the handset back into the cradle.
USING THE HOLD KEY
The HOLD key places the call on hold locally at the Opal telephone.
TO PLACE A CALL ON HOLD
1) With a call active press the red HOLD key.
2) The red line LED will change to a slow blink indicating the call
is on hold.
TO REMOVE A CALL FROM HOLD
1) Lift the handset from the cradel. This will remove the call from
hold making the call active on the handset.
- OR -
With the handset in the cradle, press the SPEAKERPHONE key.
This will remove the call from hold making the call activate the
speakerphone.
2) The red line LED will return to steady in-use condition.
TO CHANGE PHONES AFTER PLACING A CALL ON HOLD
1) Place the call on HOLD on the Opal.
2) Pickup the call at another telephone. The Opal will detect the
pickup and remove the hold condition at the original Opal.
TO MUTE SPEAKERPHONE AND HANDSET CALLS
1) Press the key, the red LED below the MUTE key will light.MUTE
The party on the other end will not hear you when the MUTE
key is depressed.
2) Press the MUTE key again to turn off the mute feature, the MUTE
LED will go out.
REDIAL
TO REDIAL THE LAST TELEPHONE NUMBER DIALED:
1) Lift the handset from the cradle, or press the SPEAKERPHONE
key.
2) Press the REDIAL key.
NOTE: Some PBX’s require a pause after the first digit to access an
outside line. The REDIAL function will automatically insert a pause if
the dialed number is 7 digits or more. The inserted pause will be of the
same duration as set in the pause timing.
FLASH KEY
The Flash key, when programmed behind an autodial key provides a
timed line interrupt typically used for accessing PBX/CO features like
transfer and conference. The timing of the hookflash is programmable
with the factory default timing set to 600 milliseconds. Some PBX’s
may require you to change the hookflash timing from the default to
600ms.
To change the hookflash timing;
1) Lift the handset.
2) Press the STORE key (see diagram for key location).
3) Press the key (see diagram for key location).FLASH
4) Select 1 - 9 on the DTMF pad. The number selected will be the
new flash timing in milliseconds (ie: “3” = 300 milliseconds).
5) Press the STORE key.
ADJUSTING THE HANDSET VOLUME
The HANDSET VOLUME key has three levels. When the handset is
first lifted, the handset volume is NORMAL.
Locate the key below the keypad. Press the keyHANDSET VOLUME
once and the volume level will increase one level (to MEDIUM vol-
ume). Press the key once more and the volume level will increase an
additional level (to HIGH volume). To return the handset volume to
NORMAL, press the handset volume key again. The handset volume
will always return to NORMAL when the handset is returned to the
cradle.
OPAL 1010S
GUESTROOM TELEPHONE
USERS GUIDE
PAUSE KEY
The Pause key, when programmed behind an autodial key can be used
to provide a timed pause between dialed digits within an autodial key.
The timing of the pause is programmable with the factory default set
to zero (0) seconds.
To change the pause timing;
1) Lift the handset.
2) Press the STORE key (see diagram for key location).
3) Press the PAUSE key (see diagram for key location).
4) Select 1 - 9 on the DTMF pad. The number selected will be the new
pause timing in seconds (ie: “3” = 3 seconds).
5) Press the STORE key.
AUTO DIAL KEYS
The Opal 1010S has ten (10) programmable AUTO DIAL keys.
These keys can be programmed to automatically dial telephone num-
bers, or activate telephone system features.
PROGRAMMING AUTO DIAL KEYS:
The telephone must be connected to a telephone line.
1) Remove the plastic overlay.
2) Lift the handset from the cradle or press the
SPEAKERPHONE key.
3) Press the recessed STORE key and release it. (Please see diagram
for key location).
4) Enter the telephone number including PAUSE* as required. The
sequence can be up to 15 digits.
5) Press the AUTO DIAL key where the number is to be stored.
6) Place the handset back in the cradle or press the SPEAKER-
PHONE key to disconnect.
RMA PROCEDURES
The following procedure should be followed with all Teledex
telephone products prior to sending the telephone to the factory
for repair.
1) Please perform the tests listed below:
a. Test the telephone on a different telephone jack.
b. Test telephone with a different line cord.
c. Test with a different handset cord (coiled cord).
d. For two line products, please ensure that one of the line
buttons is pressed (if both line buttons are in the UP position,
the telephone will not operate).
2) If the steps listed above do not provide a remedy for the suspect
telephone, please place a tag on the individual telephone
describing the defect. Next, call the Teledex Repair Department
at 1 (800) 875-8539 for an RMA number. You must have an
RMA number to return products to Teledex.
3) Kindly note: An RMA number is unique to each return
shipment. Do not duplicate this number on any future shipments.
SHIPPING INSTRUCTIONS:
Please print the RMA number clearly on the outside of your shipping
carton(s). Please ship to the following address:
Teledex LLC / RMA#___________
6311 San Ignacio Avenue
San Jose, CA 95119
FREIGHT CHARGES:
The Customer is responsible for shipping products for repair to
Teledex. After repair, Teledex will return telephone products to the
Customer freight prepaid in the same manner in which is was sent
(i.e. Freight sent to Teledex UPS Blue, will be returned via 2 day ship-
ping).
**Please note: When telephones are returned for repair due to misuse
(i.e. liquid spills, abuse, or Customer modification - warranty label
broken), the Customer will be charged the standard repair fee, regard-
less of warranty status.
CONVERTING FROM DESK TO WALL MOUNT
The Opal 1010S telephone can be changed for wall mount applica-
tions. The conversion is easiest when the handset and line cords are
not connected.
1) Located on the front of the telephone above the speaker grill is
the wall/desk mount clip. Remove this clip by firmly pushing
upward (towards the hookswitch).
2) Rotate the clip a half turn (180 degrees) so that the side with the
protruding edge is towards the top. This edge will hold the
handset. (Closest to the hookswitch.)
3) Return the clip to its original location by pushing the clip dow
wards, until it stops (snaps into place).
4) Turn the Opal 1010S over so that the back side is up, facing you
(A non abrasive surface is suggested to prevent scratching).
5) Locate and remove the mounting bracket, firmly push back and
pull up to remove two of the four retaining tabs.
6) Rotate the mounting bracket a half turn (180 degrees) so that
the mounting eyelet is facing in the same direction as the other
mounting eyelet located on the telephone.
7) Insert the top two retaining tabs of the mounting brackets into
the mounting bracket slots (located near the middle of the tele-
phone). Then firmly push down to insert the retaining tabs on
the opposite side of the mounting bracket.
8) Connect a short modular line cord into the jack on the back of
the phone (labeled TO TEL). Route the line cord through the line
cord channel. Connect the other end of line cord to the phone
jack on the wall mounting plate.
9) Turn the telephone over, and slide the Opal 1010S down onto
the wall plate mounting posts. Both eyelets should line up with
the mounting posts (When properly installed the telephone will
be stable and secure).
10) Complete the wall mounting by installing the handset and hand
set cord.
REQUIREMENTS OF PART 68 - FCC RULES
This device has been granted a registration number by the Federal Communications Commission,
under Part 68 rules and regulations for direct connection to the telephone lines. In order to comply
with these FCC rules, the following instructions must be carefully read and applicable portions fol-
lowed completely:
1. Direct connection to the telephone lines may be made only through the standard modular cord fur-
nished, to the utility installed jack. No connection may be made to party or coin phone lines. On
the bottom of the phone is a label that contains among other information, the FCC Registration
Number and the Ringer Equivalence number (REN) for this equipment. If requested this informa-
tion must be provided to the telephone company. The USOC Jack for this equipment is RJ11C.
2. The telephone company, under certain circumstances, may temporarily discontinue and make
changes in facilities and services which may affect the operation of the users' equipment: however,
the user shall be given adequate notice in writing to allow the user to maintain uninterrupted serv-
ice.
3. In certain circumstances, it may be necessary for the telephone company to request information
from you concerning the equipment which you have connected to your telephone line. Upon
request of the telephone company, provide the FCC registration number and the ringer equiva-
lence number of the equipment which is connected to your line; this information will be found on
the device.
4. If any of your telephone equipment is not operating properly, you should immediately remove it
from the telephone line. It may cause harm to the telephone network.
5. If the telephone company notes a problem, they may temporarily discontinue service. When practi-
cal, they will notify you in advance disconnection. If advance notice is not feasible, the telephone
company must; promptly notify you of such temporary discontinuance; afford the opportunity to
correct the condition; inform you of your rights to bring a complaint to the FCC under their rules.
6. Repairs to the device may be made only by the manufacturer or an authorized service agency.
This applies at any time during and after warranty. If unauthorized repair is performed, registration,
connection to the telephone lines and remainder of warranty period all become null and void.
7. This equipment is hearing aid compatible.
8. This telephone must be connected behind a PBX.
REQUIREMENTS OF PART 15 - FCC RULES
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction,
may cause harmful interference to radio communications. However, there is not a guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Move the telephone away from the receiver. -Consult the dealer or an experienced radio/TV techni-
cian for help. Any changes made by the user not approved by the manufacturer can void the user's
authority to operate the telephone.
INDUSTRY OF CANADA REQUIREMENTS
NOTICE: The Industry Canada label identifies certified equipment. This certification means that the
equipment meets certain telecommunications network protective operational and safety requirements
as prescribed in the appropriate Terminal Equipment Technical Requirements documents. The
department does not guarantee the equipment will operate to the users satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection.
The customer should be aware that compliance with the above conditions may not prevent degrada-
tion of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier.
Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utili-
ty, telephone lines, and internal metallic water pipe systems, if present, are connected together. This
precaustion may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority or electrician, as appropriate.
The Ringer Equivalence Number (REN) of this device is Z.
Notice: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indica-
tion of the maximum number of terminals allowed to be connected to a telephone interface. The ter-
mination on an interface may consist of any combination of devices subject only to the requirement
that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. This tele-
phone connects to the telephone network under the connecting arrangement code CA11A.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO
PERSONS. INCLUDING THE FOLLOWING:
1. READ AND UNDERSTAND ALL INSTRUCTIONS.
2. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE PRODUCT.
3. UNPLUG THE PRODUCT FROM THE WALL OUTLET BEFORE CLEANING. DO NOT USE LI
UID CLEANER OR AEROSOL CLEANERS. USE A DAMP CLOTH FOR CLEANING.
4. DO NOT USE THIS PRODUCT NEAR WATER FOR EXAMPLE NEAR A BATHTUB, WASH
BOWL, KITCHEN SINK OR LAUNDRY TUB, IN A WET BASEMENT, OR NEAR A SWIMMING
POOL.
5. DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND OR TABLE. THE PROD-
UCT MAY FALL, CAUSING SERIOUS DAMAGE TO THE PRODUCT.
6. SLOTS AND OPENINGS IN THE CABINET AND THE BACK OF BOTTOM ARE PROVIDED
FOR VENTILATION, TO PROTECT IT FROM OVERHEATING, THESE OPENINGS MUST
NOT BE BLOCKED OR COVERED. THE OPENINGS SHOULD NEVER BE BLOCKED BY
PLACING THE PRODUCT ON THE BED, SOFA, RUG OR ANY OTHER SIMILAR SURFACE.
THIS PRODUCT SHOULD NEVER BE PLACED NEAR OR OVER A RADIATOR OR HEAT
REGISTER. THIS PRODUCT SHOULD NOT BE PLACED IN A BUILT-IN INSTALLATION
UNLESS PROPER VENTILATION IS PROVIDED.
7. NEVER PUSH OBJECTS OF ANY KIND INTO THIS PRODUCT THROUGH CABINET SLOTS
AS THEY MAY TOUCH DANGEROUS VOLTAGE POINTS OR SHORT OUT PARTS THAT
COULD RESULT IN A RISK OF FIRE OR ELECTRIC SHOCK. NEVER SPILL LIQUID OF ANY
KIND ON THE PRODUCT.
8. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT DISASSEMBLE THIS PRODUCT
BUT TAKE IT TO A QUALIFIED SERVICEMEN WHEN SOME SERVICE OR REPAIR WORK IS
REQUIRED. OPENING OR REMOVING COVERS MAY EXPOSE YOU TO DANGEROUS
VOLTAGES OR OTHER RISKS. INCORRECT REASSEMBLE CAN CAUSE ELECTRIC
SHOCK WHEN THE APPLIANCE IS SUBSEQUENTLY USED.
9. UNPLUG THIS PRODUCT FROM THE WALL OUTLET AND REFER SERVICING TO QUAL
FIED SERVICE PERSONNEL UNDER THE FOLLOWING CONDITIONS.
· WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED OR FRAYED
· IF LIQUID HAS BEEN SPILLED INTO THE PRODUCT.
· IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER.
· IF THE PRODUCT DOES NOT OPERATE NORMALLY BY FOLLOWING THE OPERATING
INSTRUCTIONS. ADJUST ONLY THOSE CONTROLS THAT ARE COVERED BY THE
OPERATING INSTRUCTIONS BECAUSE IMPROPER ADJUSTMENTOF OTHER CON-
TROLS MAY RESULT IN DAMAGE AND WILL OFTEN REQUIRE EXTENSIVE WORK BY A
QUALIFIED TECHNICIAN TO RESTORE THE PRODUCT TO NORMAL OPERATION.
· IF THE PRODUCT HAS BEEN DROPPED OR THE CABINET HAS BEEN DAMAGED.
· IF THE PRODUCT EXHIBIT A DISTINCT CHANGE IN PERFORMANCE.
10. AVOID USING A TELEPHONE (OTHER THAN A CORDLESS TYPE) DURING AN ELECTRI-
CAL STORM. THERE MAY BE A REMOTE RISK OF ELECTRIC SHOCK FROM LIGHTING.
11. DO NOT USE THE TELEPHONE TO REPORT A GAS LEAK IN THE VICINITY OF THE LEAK.
SAVE THESE INSTRUCTIONS
FOR CUSTOMER SERVICE CALL
1-800-783-8353
Teledex, LLC
6311 San Ignacio Avenue
San Jose, CA
95119
Telephone: (408) 363-3100
Fax: (408) 363-3136
email: sales@teledex.com
Internet: www.teledex.com
Part Number 606-2660-00A
TELEDEX
OPAL 1010S
DIAGRAM
RING VOLUME
Adjusts the ringer volume
to Low or High setting.
DATA PORT
HANDSET VOLUME KEY
Changes handset volume by
pressing repeatedly.
REDIAL KEY
To automatically redial
last number dialed
AUTO DIAL KEYS 6-10
For easy, one-touch dialing of guest services or
PBX features. Programmed during installation.
AUTO DIAL KEYS 1-5
For easy, one-touch dialing of guest services or
PBX features. Programmed during installation.
MESSAGE WAITING LIGHT
Signals that a message is waiting for retrieval.
See your system administrator for instructions
on retrieving messages.
HOLD KEY
STORE KEY (hidden)
Used in programming of number sequences.
See instructions for programming details.
HANDSET HOLDER
Used to temporarily hold the handset,
without hanging up the telephone,
when telephone is wall mounted.
HEARING AID COMPATIBLE HANDSET
HANDSET JACK
Modular jack for connecting handset to base.
DIAL KEYS (DTMF PAD)
For dialing phone numbers, and entering
numbers to be stored in auto dial keys.
FLASH KEY (hidden)
For programming of FLASH duration.
SPEAKERPHONE KEY
MUTE KEY
Product specificaties
| Merk: | Teledex |
| Categorie: | Telefoon |
| Model: | Opal 1010S |
Heb je hulp nodig?
Als je hulp nodig hebt met Teledex Opal 1010S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Telefoon Teledex
26 Juni 2023
26 Juni 2023
26 Juni 2023
26 Juni 2023
26 Juni 2023
26 Juni 2023
26 Juni 2023
26 Juni 2023
26 Juni 2023
26 Juni 2023
Handleiding Telefoon
- Telefoon Philips
- Telefoon Sony
- Telefoon Samsung
- Telefoon Xiaomi
- Telefoon Panasonic
- Telefoon LG
- Telefoon Huawei
- Telefoon Asus
- Telefoon AEG
- Telefoon Fysic
- Telefoon Grundig
- Telefoon Gigaset
- Telefoon JBL
- Telefoon Motorola
- Telefoon Medion
- Telefoon Nokia
- Telefoon Pioneer
- Telefoon Siemens
- Telefoon Topcom
- Telefoon Toshiba
- Telefoon VTech
- Telefoon Wiko
- Telefoon Yamaha
- Telefoon Yealink
- Telefoon Aastra
- Telefoon Acer
- Telefoon AGFEO
- Telefoon Airis
- Telefoon Airlive
- Telefoon Alcatel
- Telefoon Alcatel-Lucent
- Telefoon Allview
- Telefoon Amplicom
- Telefoon Amplicomms
- Telefoon Anker
- Telefoon Apple
- Telefoon Archos
- Telefoon Ascom
- Telefoon Audio-Technica
- Telefoon Audioline
- Telefoon Auerswald
- Telefoon Avaya
- Telefoon AVM
- Telefoon Belgacom
- Telefoon Binatone
- Telefoon Blackberry
- Telefoon Blaupunkt
- Telefoon BT
- Telefoon D-Link
- Telefoon Davolink
- Telefoon Denver
- Telefoon Doro
- Telefoon Draytek
- Telefoon Emporia
- Telefoon Engenius
- Telefoon Envivo
- Telefoon Fenton
- Telefoon Flex
- Telefoon GE
- Telefoon Geemarc
- Telefoon Gigaset Pro
- Telefoon GPO
- Telefoon Grandstream
- Telefoon Hagenuk
- Telefoon Hama
- Telefoon Hitachi
- Telefoon Honor
- Telefoon HTC
- Telefoon HUMANTECHNIK
- Telefoon Innovaphone
- Telefoon KONFTEL
- Telefoon KPN
- Telefoon Kyocera
- Telefoon Lenovo
- Telefoon LevelOne
- Telefoon Lexibook
- Telefoon Linksys
- Telefoon Loewe
- Telefoon Logicom
- Telefoon Logik
- Telefoon Logitech
- Telefoon Mackie
- Telefoon Marmitek
- Telefoon Marquant
- Telefoon Marshall
- Telefoon Maxcom
- Telefoon Microsoft
- Telefoon Mikrotik
- Telefoon Mitel
- Telefoon MT Logic
- Telefoon Nec
- Telefoon Netgear
- Telefoon Nordmende
- Telefoon Parrot
- Telefoon Patton
- Telefoon Peaq
- Telefoon Pixel
- Telefoon Plantronics
- Telefoon Polycom
- Telefoon Premier
- Telefoon Prestigio
- Telefoon Profoon
- Telefoon Proximus
- Telefoon Pyle
- Telefoon Ranex
- Telefoon RCA
- Telefoon Realme
- Telefoon Renkforce
- Telefoon Roland
- Telefoon RugGear
- Telefoon Sagem
- Telefoon Sagemcom
- Telefoon Sencor
- Telefoon Sennheiser
- Telefoon Silvercrest
- Telefoon SMC
- Telefoon Snom
- Telefoon Spectralink
- Telefoon Sunstech
- Telefoon Sweex
- Telefoon Swissvoice
- Telefoon Switel
- Telefoon Sylvania
- Telefoon TCL
- Telefoon Tecdesk
- Telefoon Telefunken
- Telefoon Telstra
- Telefoon Thomson
- Telefoon Tiptel
- Telefoon Trendnet
- Telefoon Tristar
- Telefoon Trust
- Telefoon Uniden
- Telefoon Unify
- Telefoon Viking
- Telefoon Zebra
- Telefoon ZTE
- Telefoon ZyXEL
- Telefoon Jabra
- Telefoon Jacob Jensen
- Telefoon Olympia
- Telefoon OnePlus
- Telefoon Oppo
- Telefoon Oregon Scientific
- Telefoon Overmax
- Telefoon Essentiel B
- Telefoon Bang And Olufsen
- Telefoon BeeWi
- Telefoon CSL
- Telefoon Krüger And Matz
- Telefoon Steren
- Telefoon Ubiquiti Networks
- Telefoon Crosley
- Telefoon Infiniton
- Telefoon MXL
- Telefoon Hamlet
- Telefoon Edenwood
- Telefoon Trevi
- Telefoon Scosche
- Telefoon Oricom
- Telefoon AT&T
- Telefoon AudioCodes
- Telefoon Chacon
- Telefoon Valcom
- Telefoon SPC
- Telefoon Canyon
- Telefoon Cisco
- Telefoon EVOLVEO
- Telefoon CAT
- Telefoon Oukitel
- Telefoon 3Com
- Telefoon Planet
- Telefoon Cubot
- Telefoon Clarity
- Telefoon Xblitz
- Telefoon VXi
- Telefoon Lindy
- Telefoon AVerMedia
- Telefoon Fortinet
- Telefoon Bogen
- Telefoon ArtDio
- Telefoon XD Enjoy
- Telefoon CTA Digital
- Telefoon MyPhone
- Telefoon Fanvil
- Telefoon Crestron
- Telefoon Yeastar
- Telefoon JPL
- Telefoon OpenVox
- Telefoon Gamdias
- Telefoon Primare
- Telefoon Syco
- Telefoon Edge-Core
- Telefoon Vimar
- Telefoon Akuvox
- Telefoon Legrand
- Telefoon Digium
- Telefoon Clear Sounds
- Telefoon Mitsai
- Telefoon ALLO
- Telefoon On-Q
- Telefoon Lewitt
- Telefoon Tecno
- Telefoon Vogtec
- Telefoon Olitech
- Telefoon Dopod
- Telefoon Sedna
- Telefoon British Telecom
- Telefoon CyberData Systems
- Telefoon Cortelco
- Telefoon Bintec-elmeg
- Telefoon EMeet
- Telefoon Wantec
- Telefoon Neat
- Telefoon Algo
- Telefoon Future Call
- Telefoon 4family
- Telefoon Tador
- Telefoon Dnake
- Telefoon Liam&Daan
- Telefoon FlyingVoice
Nieuwste handleidingen voor Telefoon
19 November 2024
17 November 2024
17 November 2024
17 November 2024
17 November 2024
16 November 2024
16 November 2024
16 November 2024
16 November 2024
16 November 2024