Techno Line WS 9250 Handleiding

Techno Line WS 9250

Lees hieronder de 📖 handleiding in het Nederlandse voor Techno Line WS 9250 (5 pagina's) in de categorie . Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

WS9250 TEMPERATURE STATION WITH ICE ALERT –

USER’S INSTRUCTION

Please read the instructions carefully and keep the manual well for future reference.

GETTING STARTED

Before using the main unit and transmitter:

1. Remove the battery door of the main unit and transmitter.

2. Install 2 new AA size batteries for both of the unit and transmitter, according to the polarity

information marked on the battery compartment.

3. Replace the battery door.

4. After the batteries are installed, all the segment of the LCD will be shown.

5. Press the “RESET” key at the back of the main unit first, and press the “RESET” key of the

transmitter.

6. It will receive 433 MHz signal for channel test automatically in 8 seconds. And after 5 minutes for

channel test, it will turn to RC signal reception automatically.

Note:

1. The unit can receive and display the readings from up to 3 remote transmitters.

2. Position the unit and transmitter within the effective transmission range: 50 meters in usual

circumstances.

3. In some cases, you may not receive the signal immediately, you can reset the unit and transmitter

again as described in the above section.

MAIN FEATURES

MAIN UNIT:

1. LCD display

- Display of the time, alarm time, outdoor & indoor temperature.

2. SNOOZE / LIGHT key

- Press it to turn on and keep the backlight for 5 seconds.

- When the alarm is sounding, press it to stop the current alarm and turn to snooze.

3. ALARM SET key

- Press it to display and keep the alarm time for 5 seconds. During the alarm time displayed riod, pe

press it to turn on/oﬀ alarm function.

- Press and hold it for 3 seconds to enter alarm time setting mode.

- In alarm time setting mode, press it to step the setting item, and press it to save and exit the setting

after setting the minute.

4. CH/+ k ey

- In setting mode, press it to adjust the value of the ﬂashing digit upwards. And press it without

releasing to speed up the setting.

- In normal mode, press it to manually check the outdoor temperature from channel 1 to channel 3.

Press and hold it for 3 seconds to turn to channel auto-change mode. Press it again to return to

normal mode.

5. MEM/- key

- In setting mode, press it to adjust the value of the ﬂashing digit downwards. And press it without

releasing to speed up the setting.

- Press it to check and keep the max/min indoor and outdoor temperature for 5 seconds.

- Press and hold it for 3 seconds to delete the max./min. temperature records.

6. DIAPLAY SET key

- In normal mode, press and hold it for 3 seconds to enter time setting mode.

- In time setting mode, press it to step the setting item, and press and hold it for 3 seconds to save and

exit the setting.

7. °C/°F slide switch

- Slide it to switch temperature unit between °C/°F.

8. SENSOR key

- Press it to manual receiving 433 MHz signal for channel test.

- During the reception test, press and hold it for 3 seconds to turn oﬀ the channel test.

9. RCC key

- Press it to manually receiving RC signal.

- During the RC reception, press and hold it for 3 seconds to turn oﬀ the reception.

10. RESET key

- In case of mal-function, press it by using a metal wire to reset all the values.

11. Battery door

TRANSMITTER:

1. LED indicator

- Flashes when the remote unit transmits a reading.

2. CHANNEL slide switch

- Assign the transmitter to Channel 1, 2 or 3.

3. RESET key

- Press it to reset the transmitter.

4. Wall-mounting holder

- Use it to support the transmitter on the wall.

5. Battery compartment

SIGNAL STRENGTH INDICATOR

The signal indicator flashing means time signals are being received. If the RC temperature station

receives signal successfully, a sync- the LCD and the unit has already time symbol “ ” appears on

received the time signal. Otherwise, the signal strength symbol will disappear from the LCD display.

Note:

You may press “RCC” key to receive the time signal manually. The receive mode will be oﬀ

automatically after 6-16 minutes. Receive mode consumes more battery power that may reduce

battery lifetime.

DAYLIGHT SAVING TIME(DST)

The temperature station has been programmed to automatically switch when daylight saving time is in

eﬀect. Your temperature station will display “DST” on the LCD during the summer.

TIME AND CALENDAR SETTING

If the temperature station does not receive the time signal successfully, you can set the time manually.

As soon as the transmitter is received again, the temperature station will automatically synchronize

with the received time.

1. In normal mode, press and hold “DISPLAY SET” key for 3 seconds until the Hour format digit

ﬂashing.

2. Press “+” / “ ” key to- select 12/24 hour format.

3. Press “DISPLAY SET” key again to step the setting item to Hour with the Hour digit ﬂashing.

4. Press “+” / “ ” key to adjust the value of the- ﬂashing digit.

5. Do the above operation in this sequence: 12/24 Hr > Hour > Minute > Second > Time zone.

6. Press and hold “ ” key for 3 seconds to saveDISPLAY SET and exit the setting.

Note:

If your local time is diﬀerent from the RC received time, you can set the desired time zone.

The available time diﬀerence is from -23 hours to +23 hours. After setting the desired time diﬀerence,

the temperature station will show the time that RC received time plus/minus the time diﬀerence.

ALARM TIME SETTING

1. In normal time mode, press and hold “ALARM SET” key for 3 seconds until the Ho ur digit ﬂashing.

2. Press “+” / “ ” key to adjust the value of the- flashing digit.

3. Press “ALARM SET” key again to step the setting value to Minute with the Minute digit ﬂashing.

4. Press “+” / “ ” key to adjust the value of the- flashing digit.

5. Pre setting. ss “ALARM SET” key to save and exit the

Note:

The alarm function will turn on automatically once you set the alarm time.

USING ALARM AND SNOOZE FUNCTION

1. Set the desired alarm time as described in the above section.

2. Press “ALARM SET” key to display the alarm time, press it again to turn on alarm function with the

alarm icon “ ” displayed on the LCD.

3. When temperature station reach the alarm time, alarm sound will start. Where, it can be stopped by

following operation:

1). Auto-stop after two minutes alarming if without any operation and it will re-alarm by the next day.

2). By pressing “SNOOZE” key to enter snooze that the alarm will sound again after 5 minutes.

3). By pressing “ALARM SET” key to turn off the alarm function.

Note:

1. The snooze could be used continuously in 24 hours.

2. During the snooze, the alarm icon will keep ﬂashing.

VIEW THE CHANNEL

Product specificaties

Merk:	Techno Line
Categorie:
Model:	WS 9250
Kleur van het product:	Zwart
Ingebouwd display:	Ja
Breedte:	84 mm
Diepte:	48 mm
Hoogte:	100 mm
Alarm functie:	Ja
Klok functie:	Ja
Meetfuncties:	Indoor thermometer, Outdoor thermometer
Meetfuncties trend display:	Thermometer
weerstation extremum data:	Thermometer
Weersvoorspelling:	Nee
Receiver afmetingen (B x D x H):	65 x 35 x 100 mm
Type batterij:	AA
Display met achtergrondverlichting:	Ja
Min/Max temperatuur geheugen:	Ja
DCF radio klok:	Ja