Tascam RC-828 Handleiding
Tascam
Afstandsbediening
RC-828
Lees hieronder de 📖 handleiding in het Nederlandse voor Tascam RC-828 (7 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/7
Section 1 – Starting to use the RC-828
0.98 – 1
1 – Starting to use the RC-828
The TASCAM RC-828 Remote Control Unit
allows you to control up to 4 DTRS1 recorders
(any combination of DA-98, DA-38 or DA-98
units) from one location. The functions which
may be controlled are:
• Transport operations (including jog and
shuttle)
• Track arming
• Auto punch operations
• Chasing control
• Location memories and auto-repeat between
two points
This manual makes reference to the manuals of
the following units: DA-88, DA-38, DA-98 and
SY-88. Please consult these documents as neces-
sary when setting up and using the RC-828.
1.1 Hooking up the RC-828
The RC-828 and DTRS units form a “daisy-
chain”, with the RC-828 being at the head, and the
“tail” unit being terminated with the terminator
supplied with the RC-828.
Use the suppled cable to connect the RC-828 to
the REMOTE IN/SYNC IN of the first DTRS
unit, and a PW-88S cable to connect the SYNC
OUT of the first unit to the REMOTE IN/SYNC
IN of the next unit, and so on, until the terminator
is connected to the SYNC OUT of the last unit in
the chain.
The RC-828’s REC FUNCTION keys 1 through
8 now control the first unit, Keys 9 through 16
control the next unit in the chain, and so on
(regardless of the actual Machine IDs of the
units).
Tighten the screws holding the cable connector to
the RC-828 and to the DTRS unit. This will pre-
vent accidental disconnection of the RC-828 in
the middle of a session.
No power connection is needed for the RC-828.
All power for LEDs, etc. is supplied by the first
DTRS unit.
1.1.1 Machine IDs
Set the machine IDs of the DTRS units so that the
IDs run in a sequence from the unit at the “head”
of the chain, closest to the RC-828 (lowest possi-
ble ID) to the “tail” unit (highest ID). There
should be no gaps in this sequence.
A DA-88 uses a rotary switch to set the ID and
uses 0 as the lowest ID, and a DA-38 or DA-98
uses software to make this setting, and uses 1 as
the lowest ID. Refer to the units’ manuals for full
details of setting the ID.
1 DTRS is a trademark of TEAC Corporation
NOTE
When you connect a number of DTRS units which are of
dierent types, including a DA-98, the DA-98 should be at
the head of the chain immediately following the RC-828.
Other units may then be connected in any order.
If the DTRS units are DA-88s and DA-38s only, they may
be connected in any order.
WARNING
Turn o power to all units when making connections. If you
do not do this, there is a possibility that the RC-828 will
malfunction or even be damaged.
RC-828 DA-38DA-98 DA-88
OUT OUT OUT
IN IN IN
Terminator
Cable supplied
with RC-828
PW-88S PW-88S
WARNING
Use only TASCAM cables to connect the RC-828 to the first
DTRS unit, and to connect the DTRS units to each other. If
the use of cables other than TASCAM cables causes or
results in damage to the units, the warranty is voided.
NOTE
At least one LED is always lit on the RC-828 when it is con-
nected and power is switched on to the DTRS units. If you
do not see any lit LEDs on the RC-828, make sure the
DTRS power is switched on, and check the cable connec-
tions to the RC-828.
Unit
ID as shown
“Real” ID
How the ID is
set (see the
unit’s manual
for details)
Power on or o
when ID is set
DA-98 1 1 Menu system (see
9.2)
ON
DA-88 0 1 Rotary switch on
rear panel (see p23–
24)
OFF
DA-38 1 1 Tape counter menu
system (see 7-2)
ON
Section 2 – Parts of the RC-828
2 – 0.98
1.1.2 Chase mode
In an all-audio setup, the first unit is unlikely to be
chasing external sources. However, subsequent
units in the chain should now chase this master,
using the DTRS (ABS) sync method, when their
CHASE switches are pressed.
However, in some audio setups or an audio-visual
setup, it may be necessary to make the master
DTRS unit slave to incoming timecode:
In this case, you should take care to set the clock
reference of the master DTRS unit appropriately.
2 – Parts of the RC-828
[1] REMOTE connector
Connect one end of the supplied cable to this con-
nector, and the other end to the first DTRS unit, as
described in 1.1, “Hooking up the RC-828”. Make
sure the power to the DTRS unit is turned o
when you make the connection.
[2] REC FUNCTION keys and
indicators
The 32 REC FUNCTION keys allow you to arm
the tracks of up to four DTRS units. Keys 1–8
control the tracks of the first unit in the chain, 9–
16 those of the second, and so on. Pressing keys
which correspond to a non-existent DTRS unit
will have no eect.
Pressing the corresponding keys on the DTRS
units has the same effect as pressing the keys on
the RC-828 unit (i.e. if the track is not armed, it
will now be armed, and vice versa).
The indicators flash when a track is armed for
recording, and light solidly when recording is
being rehearsed or taking place.
[3] CHASE keys and indicators
These keys and indicators allow you to set and
view the chase status of the DTRS units connected
to the RC-828 in the same way as the CHASE
keys and indicators on the units themselves.
[4] ALL INPUT key and indicator
This key performs the same function as the ALL
INPUT key on a DTRS unit, switching the moni-
toring of all tracks on all connected units to the
input source. The indicator lights when this mode
is active.
The INPUT MONITOR keys on the DA-98 also
affect the switching between source and tape.
Using the RC-828 REC FUNCTION keys to
change the status of any tracks while the ALL
INPUT function is on will lose the relationship
between the REC FUNCTION and INPUT
MONITOR status for individual tracks when ALL
INPUT is turned off again. Start recording or re-
set the REC FUNCTION keys to restore this.
If you want to monitor using confidence mode on
a DA-98 unit, make sure that the ALL INPUT key
is off and use the INPUT MONITOR keys on the
DA-98 to turn off input monitoring on all tracks.
[5] AUTO MON key
This key is equivalent to the AUTO MON key on
the DA-98 and performs the same function as this
key on any connected DA-98 units. There is no
key with the same name on the DA-38 or DA-88;
pressing this key is the equivalent of pressing the
INSERT key on a connected DA-38, and pressing
both the AUTO INPUT and INSERT keys on a
DA-88. It is used in punch modes to switch auto-
matically between tape and source when punching
in and out automatically. The indicator lights
when this function is active.
Note that the status of the INPUT MONITOR
keys on a DA-98 will be overridden by the AUTO
MON key. However, when AUTO MON is turned
off again, the original status of these keys will be
restored.
Using the RC-828 REC FUNCTION keys to
change the status of DA-98 tracks while AUTO
MON is on will lose the relationship between the
REC FUNCTION and INPUT MONITOR status
for individual tracks when AUTO MON is turned
off again. Start recording or re-set the REC
FUNCTION keys to restore this.
If you want to monitor using confidence mode on
a DA-98 unit, make sure that the AUTO MON key
NOTE
When you set the machine IDs, you can set the ID of any
machine first, but we recommend doing this in a standard
sequence, working from the head of the chain to the tail.
Reference
DA-98 DA-38 DA-88 SY-88
9.2.3 7-3 p. 24 —
Reference
DA-98 DA-38 DA-88 SY-88
10.7.1 — — 5-1
Reference
DA-98 DA-38 DA-88 SY-88
7.1.1 9.1 (1) p. 9 (18) —
Section 2 – Parts of the RC-828
0.98 – 3
is off and use the INPUT MONITOR keys on
the DA-98 to turn off input monitoring on all
tracks.
[6] JOG/SHTL MON key and indicator
This key allows the selection of different monitor-
ing modes when shuttle mode is selected, either
with the units’ own SHUTTLE controls, or from
the JOG/SHUTTLE key on the RC-828 [15].
This key and indicator duplicate the function of
the SHTL MON key and indicator of the DA-98,
and provide these capabilities for the DA-38 and
DA-98.
Use the flowchart provided with this manual to
check the shuttle monitoring status of DA-38 and
DA-88 units in different modes (the provision of
confidence mode on the DA-98 means that this
model differs from the others), and you should
also consult the manual of the DTRS unit for full
details, if you are unclear about how shuttle moni-
toring works:
[7] RHSL key
This key duplicates the functions of the corre-
sponding key controlling rehearsal operations on
the DTRS units. See the appropriate section of the
DTRS manual if you are unsure of its operation.
[8] AUTO PUNCH key
This key duplicates the functions of the corre-
sponding key controlling auto punch operations
on the DTRS units. See the appropriate section of
the DTRS manual if you are unsure of its
operation.
[9] CLEAR key
This key duplicates the functions of the corre-
sponding key clearing punch points on the DTRS
units. See the appropriate section of the DTRS
manual if you are unsure of its operation.
[10] LOCATE POINTS 1–12
These 12 location keys and indicators are used for
the management of location memories. These
memories are stored and used with reference to
the DTRS unit’s current time reference (ABS or
timecode).
The indicator of a location memory containing a
location point will be lit, and pressing the key
(except in “capture” or erase mode, see [11] and
[12]) will locate to the point stored in that mem-
ory. Pressing a key whose indicator is not lit will
have no effect. The location point stored in the
memory will be briefly shown on the tape counter
of the DTRS units (for the DA-88 and DA-38–for
the DA-98 the location point will be shown briefly
on the LCD display screen).
While location is taking place, the indicator will
flash, and the indicator will light steadily again
when location is complete.
If the AUTO PLAY indicator [13] is lit, the DTRS
unit will start to play back when the location point
is reached, otherwise the transport will stop at the
location point.
[11] CAPTURE key and indicator
Press this key to enter “capture” mode. The green
indicator will flash. While in capture mode, press-
ing a LOCATE POINT key [10] will store the
current tape position to the location memory cor-
responding to the LOCATE POINT key.
If the memory does not contain data (the indicator
is not lit), the new position will be written to the
memory and the indicator will light. If the mem-
ory already contains a location point (the indicator
is lit), this will be overwritten with the new posi-
tion. Press the CAPTURE key again to turn off
the capture mode (the indicator will stop flashing).
[12] ERASE key
To erase a location memory, press and hold down
the ERASE key. While holding it down, press the
LOCATE POINT key [10] of the memory you
want to erase. The indicator of the LOCATE
Reference
DA-98 DA-38 DA-88 SY-88
7.1.3 — — —
Reference
DA-98 DA-38 DA-88 SY-88
6.6 4-3 p. 16 —
NOTE
These location memories are independent of the MEMO 1
and 2 location memories stored in the DTRS units.
NOTE
The location points are stored in memory, backed up by a
battery whose life is a few years. When you turn on the
DTRS unit connected to the RC-828 with location memo-
ries stored in it, the same location indicators will light as
were lit at the time when you last turned o the DTRS unit.
If they do not light, the battery needs replacing, and you
should contact your TASCAM dealer regarding a replace-
ment battery.
Product specificaties
Merk: | Tascam |
Categorie: | Afstandsbediening |
Model: | RC-828 |
Heb je hulp nodig?
Als je hulp nodig hebt met Tascam RC-828 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Afstandsbediening Tascam
24 Mei 2023
6 Mei 2023
18 April 2023
19 Februari 2023
7 Februari 2023
6 Februari 2023
29 Januari 2023
18 Januari 2023
Handleiding Afstandsbediening
- Afstandsbediening Philips
- Afstandsbediening Sony
- Afstandsbediening Samsung
- Afstandsbediening Xiaomi
- Afstandsbediening Panasonic
- Afstandsbediening Nikon
- Afstandsbediening LG
- Afstandsbediening AEG
- Afstandsbediening Canon
- Afstandsbediening Garmin
- Afstandsbediening Grundig
- Afstandsbediening Honeywell
- Afstandsbediening JVC
- Afstandsbediening Kenwood
- Afstandsbediening Miele
- Afstandsbediening Motorola
- Afstandsbediening Medion
- Afstandsbediening Onkyo
- Afstandsbediening Pioneer
- Afstandsbediening Toshiba
- Afstandsbediening UPC
- Afstandsbediening Yamaha
- Afstandsbediening Absima
- Afstandsbediening Abus
- Afstandsbediening Alpine
- Afstandsbediening Amazon
- Afstandsbediening Ansmann
- Afstandsbediening Antec
- Afstandsbediening Apart
- Afstandsbediening Apple
- Afstandsbediening Arcam
- Afstandsbediening Artsound
- Afstandsbediening AT-T
- Afstandsbediening Audiovox
- Afstandsbediening Autel
- Afstandsbediening Axis
- Afstandsbediening Bang Olufsen
- Afstandsbediening BeamZ
- Afstandsbediening Benning
- Afstandsbediening Beoplay
- Afstandsbediening Bose
- Afstandsbediening Brennenstuhl
- Afstandsbediening Danfoss
- Afstandsbediening Devolo
- Afstandsbediening DJI
- Afstandsbediening Doro
- Afstandsbediening Dual
- Afstandsbediening Ebode
- Afstandsbediening Edision
- Afstandsbediening Emtec
- Afstandsbediening Energy Sistem
- Afstandsbediening Entone
- Afstandsbediening EQ-3
- Afstandsbediening ESYLUX
- Afstandsbediening Exxter
- Afstandsbediening Ezviz
- Afstandsbediening Ferguson
- Afstandsbediening FireAngel
- Afstandsbediening Furman
- Afstandsbediening Fusion
- Afstandsbediening Gaggenau
- Afstandsbediening Geemarc
- Afstandsbediening Genius
- Afstandsbediening Glashart Media
- Afstandsbediening Grohe
- Afstandsbediening Hager
- Afstandsbediening Hama
- Afstandsbediening Hannspree
- Afstandsbediening Harman Kardon
- Afstandsbediening Hartig Helling
- Afstandsbediening Hema
- Afstandsbediening Hikvision
- Afstandsbediening HQ
- Afstandsbediening Humax
- Afstandsbediening Hunter
- Afstandsbediening Iiyama
- Afstandsbediening Infinity
- Afstandsbediening Insignia
- Afstandsbediening Kathrein
- Afstandsbediening Kensington
- Afstandsbediening Kicker
- Afstandsbediening KlikaanKlikuit
- Afstandsbediening Konig
- Afstandsbediening KPN
- Afstandsbediening Lifetec
- Afstandsbediening Loewe
- Afstandsbediening Logic3
- Afstandsbediening Logilink
- Afstandsbediening Logitech
- Afstandsbediening Maginon
- Afstandsbediening Marantz
- Afstandsbediening Marmitek
- Afstandsbediening Maximex
- Afstandsbediening MB Quart
- Afstandsbediening Medion MD6461
- Afstandsbediening Meliconi
- Afstandsbediening Metronic
- Afstandsbediening Milwaukee
- Afstandsbediening Mitsubishi
- Afstandsbediening Monacor
- Afstandsbediening Multibox
- Afstandsbediening NAD
- Afstandsbediening Naim
- Afstandsbediening Nec
- Afstandsbediening Nedis
- Afstandsbediening Neewer
- Afstandsbediening Nemef
- Afstandsbediening Niko
- Afstandsbediening Packard Bell
- Afstandsbediening Parkside
- Afstandsbediening Parrot
- Afstandsbediening Perel
- Afstandsbediening Pixel
- Afstandsbediening Prolectrix
- Afstandsbediening Provision
- Afstandsbediening Provision ISR
- Afstandsbediening Q-Sonic
- Afstandsbediening Rademacher
- Afstandsbediening RadioShack
- Afstandsbediening Ranex
- Afstandsbediening RCA
- Afstandsbediening Reely
- Afstandsbediening Reflecta
- Afstandsbediening Remotec
- Afstandsbediening Revo
- Afstandsbediening Revox
- Afstandsbediening Rockford Fosgate
- Afstandsbediening Rotel
- Afstandsbediening Ruwido
- Afstandsbediening Samlex
- Afstandsbediening Schaudt
- Afstandsbediening Silvercrest
- Afstandsbediening Sitecom
- Afstandsbediening Skymaster
- Afstandsbediening Smart
- Afstandsbediening Smartwares
- Afstandsbediening Sonos
- Afstandsbediening Spektrum
- Afstandsbediening Steinel
- Afstandsbediening Strong
- Afstandsbediening Sunwave
- Afstandsbediening Sweex
- Afstandsbediening Tado
- Afstandsbediening Targus
- Afstandsbediening TCM
- Afstandsbediening Technaxx
- Afstandsbediening Technics
- Afstandsbediening Technika
- Afstandsbediening Telefunken
- Afstandsbediening Tevion
- Afstandsbediening Tevion (Medion)
- Afstandsbediening Thomson
- Afstandsbediening Tihao
- Afstandsbediening Toa
- Afstandsbediening TomTom
- Afstandsbediening Trust
- Afstandsbediening TV Vlaanderen
- Afstandsbediening Uni-T
- Afstandsbediening Unitron
- Afstandsbediening Universal Electronics
- Afstandsbediening Universal Remote Control
- Afstandsbediening VDO Dayton
- Afstandsbediening Velleman
- Afstandsbediening Verizon
- Afstandsbediening Viper
- Afstandsbediening Vivanco
- Afstandsbediening Vizio
- Afstandsbediening Vogels
- Afstandsbediening Voxx
- Afstandsbediening Wacom
- Afstandsbediening Waeco
- Afstandsbediening Walkera
- Afstandsbediening Watson
- Afstandsbediening Xavax
- Afstandsbediening Yale
- Afstandsbediening Zalman
- Afstandsbediening Zapman
- Afstandsbediening Ziggo
- Afstandsbediening Jasco
- Afstandsbediening Jensen
- Afstandsbediening JL Audio
- Afstandsbediening Jolly
- Afstandsbediening Jung
- Afstandsbediening OEM
- Afstandsbediening Olympia
- Afstandsbediening Omega
- Afstandsbediening One For All
- Afstandsbediening Online
- Afstandsbediening Optex
- Afstandsbediening Clas Ohlson
- Afstandsbediening Continental Edison
- Afstandsbediening Bang And Olufsen
- Afstandsbediening CSL
- Afstandsbediening Exibel
- Afstandsbediening Schwaiger
- Afstandsbediening Steren
- Afstandsbediening T'nB
- Afstandsbediening Clarion
- Afstandsbediening Televés
- Afstandsbediening Cotech
- Afstandsbediening Aplic
- Afstandsbediening Ardes
- Afstandsbediening SilverStone
- Afstandsbediening Vakoss
- Afstandsbediening Elbe
- Afstandsbediening Majestic
- Afstandsbediening Malmbergs
- Afstandsbediening Msonic
- Afstandsbediening Natec
- Afstandsbediening Satechi
- Afstandsbediening SIIG
- Afstandsbediening DSC
- Afstandsbediening REV
- Afstandsbediening Zephir
- Afstandsbediening Scosche
- Afstandsbediening Tripp Lite
- Afstandsbediening American DJ
- Afstandsbediening Chauvet
- Afstandsbediening Nexa
- Afstandsbediening Cisco
- Afstandsbediening Pro-Ject
- Afstandsbediening Vello
- Afstandsbediening Delta Dore
- Afstandsbediening Fantini Cosmi
- Afstandsbediening Vision
- Afstandsbediening Asustor
- Afstandsbediening Gefen
- Afstandsbediening Ei Electronics
- Afstandsbediening Electia
- Afstandsbediening Fibaro
- Afstandsbediening Innr
- Afstandsbediening Chief
- Afstandsbediening Chamberlain
- Afstandsbediening Magnus
- Afstandsbediening Manfrotto
- Afstandsbediening CGV
- Afstandsbediening CME
- Afstandsbediening Heitech
- Afstandsbediening Swiss Sense
- Afstandsbediening Tiq
- Afstandsbediening Interphone
- Afstandsbediening Lindy
- Afstandsbediening IOGEAR
- Afstandsbediening Xit
- Afstandsbediening Hähnel
- Afstandsbediening DataVideo
- Afstandsbediening Vaddio
- Afstandsbediening Bigben Interactive
- Afstandsbediening Adj
- Afstandsbediening AV:link
- Afstandsbediening Neumann
- Afstandsbediening Valueline
- Afstandsbediening Busch-Jaeger
- Afstandsbediening EVE
- Afstandsbediening Projecta
- Afstandsbediening Genaray
- Afstandsbediening Nanlite
- Afstandsbediening Profoto
- Afstandsbediening Metra
- Afstandsbediening Russound
- Afstandsbediening Engel Axil
- Afstandsbediening Hegel
- Afstandsbediening RGBlink
- Afstandsbediening Bazooka
- Afstandsbediening Wentronic
- Afstandsbediening EQ3
- Afstandsbediening Homematic IP
- Afstandsbediening Extron
- Afstandsbediening Neets
- Afstandsbediening AMX
- Afstandsbediening Arctic Cooling
- Afstandsbediening Crestron
- Afstandsbediening ORNO
- Afstandsbediening ETiger
- Afstandsbediening Aeon Labs
- Afstandsbediening AudioControl
- Afstandsbediening Aputure
- Afstandsbediening Fortin
- Afstandsbediening Simplify
- Afstandsbediening Wet Sounds
- Afstandsbediening SVS
- Afstandsbediening ProMaster
- Afstandsbediening Match
- Afstandsbediening Libec
- Afstandsbediening Vimar
- Afstandsbediening Morel
- Afstandsbediening Antelope Audio
- Afstandsbediening H-Tronic
- Afstandsbediening PDP
- Afstandsbediening Intertechno
- Afstandsbediening Ecler
- Afstandsbediening PeakTech
- Afstandsbediening Elite Screens
- Afstandsbediening Roswell
- Afstandsbediening SpeakerCraft
- Afstandsbediening Syrp
- Afstandsbediening Bravo
- Afstandsbediening Pentatech
- Afstandsbediening PowerBass
- Afstandsbediening TELE System
- Afstandsbediening Multibrackets
- Afstandsbediening Audiofrog
- Afstandsbediening Memphis Audio
- Afstandsbediening Nanoleaf
- Afstandsbediening GBS Elettronica
- Afstandsbediening Sonoff
- Afstandsbediening Gewiss
- Afstandsbediening Insteon
- Afstandsbediening Mosconi
- Afstandsbediening Lutron
- Afstandsbediening C2G
- Afstandsbediening Control4
- Afstandsbediening MIOPS
- Afstandsbediening Compustar
- Afstandsbediening Ridem
Nieuwste handleidingen voor Afstandsbediening
19 November 2024
18 November 2024
18 November 2024
17 November 2024
16 November 2024
16 November 2024
16 November 2024
16 November 2024
16 November 2024
5 November 2024