SureFire STILETTO PRO II Handleiding

SureFire Zaklamp STILETTO PRO II

Lees hieronder de 📖 handleiding in het Nederlandse voor SureFire STILETTO PRO II (2 pagina's) in de categorie Zaklamp. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
MULTI-OUTPUT RECHARGEABLE POCKET LED FLASHLIGHT
PLR-C
USER MANUAL
18300 MT. BALDY CIRCLE
FOUNTAIN VALLEY, CA 92708-6122
SUREFIRE.COM
Revision A 7-2023
71-01-1144
PLR-C
PLR-C
OUTPUT Low: 25 Med: 500 High: 1,500 lumens
RUNTIME Low: 23.5 Med: 1.5 High: 1.0 hours
STROBE RATE Tactical Switch: 9 Emergency: 3-4 Hz
PEAK BEAM INTENSITY 35,000 candela
DISTANCE 375 meters
CONSTRUCTION Aluminum
FINISH Hard Anodized (MIL-A-8625 Type III, Class 2)
WEIGHT (w/batteries) 5.0 oz (140 g)
LENGTH 4.87 in (12.4 cm)
BEZEL DIAMETER 2x0.88 in (2.2 cm)
BATTERIES Lithium polymer rechargeable (integrated)
SWITCHING Primary, Tactical, and Programming
LIQUID INGRESS
PROTECTION
IPX7
All performance claims tested to ANSI/PLATO FL 1-2019 Standard.
SPECIFICATIONS
THE SUREFIRE NO-HASSLE GUARANTEE
We’ll do what it takes to keep your SureFire gear running smoothly. SureFire
warrants that if you our customer purchase one of our products, and we determine
that it is defective in material and/or workmanship during your lifetime, we will repair or
replace it no hassle!
The warranty does not cover any damages resulting from normal wear and tear, misuse,
abuse, negligence, or unauthorized modifications or user repairs. In the event that an
issue with a Surefire product is not covered under
this warranty Surefire can arrange to have the product repaired for a reasonable fee.
STANDARD DISCLAIMER
Except as specified above or prohibited by applicable law: all express or implied
conditions and warranties, including, without limitation, any implied warranty or condition
of merchantability or fitness for a particular purpose, or accuracy of any informational
content, are hereby excluded and disclaimed by SureFire; and in no event will SureFire
be liable for any special, direct, indirect, consequential, incidental or punitive damages
howsoever arising and regardless of the theory of liability, even if advised of the possibility
of such damages. Products, prices, availability, specifications, and offers are subject to
change or cancellation at any time without notice.
WARRANTY CLAIMS
For claims, contact Customer Service at 714-545-9444 to obtain a Return
Merchandise Authorization number (RMA#). Then package the unit carefully
and send to (no CODs):
SureFire, LLC.
Repairs Department, RMA#____
17680 Newhope Street, Suite B
Fountain Valley, CA 92708
SureFire will pay any reasonable shipping costs to return the unit to you.
Do not attempt to remove or replace the STILETTO PRO battery. Doing
so will void the warranty. If the STILETTO PRO needs to be repaired,
contact SureFire at 714-545-9444 or technicalsupport@surefire.com.
BATTERY INFORMATION & WARNING
KIT CONTENTS
STILETTO PRO II
USB-C cable
T8 Torx Wrench
CHARGING THE STILETTO PRO II
The STILETTO PRO II is powered by an integral lithium polymer (LiPo) battery (1,600 mAh).
The STILETTO PRO II’s USB-C port is for charging input only (Standard 5V, 1A max).
How to charge the LiPo rechargeable battery:
1. Insert the USB-C cable plug into charging port.STILETTO PRO II
2. Insert USB cable plug into a USB port of a computer or another device that will provide
power to the STILETTO PRO II.
3. When the fuel gauge flashes green, the STILETTO PRO II is charged to more than 98%.
NOTE: The light will function while charging at both the low and medium outputs. High output will
not function while charging.
NOTE: Charging a fully depleted battery can take up to three hours. The light may be left plugged into
the charger without damaging the battery.
NOTE: When the
STILETTO PRO II
is being charged and the temperature is too cold (Below 32°F/0°C)
or too hot (Above 120°F/50°C), the fuel gauge will blink yellow which indicates charging stopped.
Once the temperature reaches 4F/5°C or 113°F/45°C, it will continue charging. When the battery
is drained below 3.0V, the STILETTO PRO II has a pre-charge mode when connected to a charger.
The Fuel Gauge will blink red rapidly until the battery reaches 3.1V. Once the battery has a minimum
of 3.1V, the Fuel Gauge conditions above will apply.
FUEL GAUGE
The STILETTO PRO II is equipped with a LED that displays the battery status, both during use
and while charging.
LIGHT OPERATION - PROFILE CONFIGURATION
PRIMARY switch: activates the light in the various outputs
PROGRAMMING switch: see “HOW TO CHANGE PRIMARY AND TACTICAL MODES”
TACTICAL switch: for momentary, strobe or constant-on output
Primary Switch Activation
Mode 1 (Default): Press the PRIMARY switch to cycle from LOW to MEDIUM to HIGH to OFF. The cycle
will repeat if the PRIMARY switch is pressed within two seconds. If the STILETTO PRO II is activated
on either LOW, MEDIUM or HIGH and the PRIMARY switch has not been pressed within two seconds,
the next press shuts the light OFF. The last used output is not remembered.
Mode 2: Same as above, but with the cycle changed to HIGH to MEDIUM to LOW to OFF.
Tactical Switch Activation
Mode 1 (Default ; TACTICAL & STROBE): Press and hold the TACTICAL switch for HIGH only; release
the switch to shut OFF. For STROBE, rapidly tap the TACTICAL switch three or more times and hold
down on the 3rd+ press. Release the switch to shut the STROBE OFF.
Mode 2 (Constant-on): Press the TACTICAL switch for constant-on in HIGH only. When the switch is
pressed again, the light will shut OFF.
EMERGENCY MODE Activation
Press and hold the PROGRAMMING switch for five seconds or more to activate the MEDIUM frequency,
MEDIUM output STROBE. Press the PRIMARY or TACTICAL switch to shut EMERGENCY MODE OFF.
HOW TO CHANGE PRIMARY AND TACTICAL MODES
The PROGRAMMING switch is used to select the behavior of the PRIMARY and TACTICAL
output buttons. The STILETTO PRO II must be off to change modes. The PRIMARY and TACTI-
CAL switches are changed independently (Ex: PRIMARY switch can be on MODE 1 and TACTI-
CAL switch can be on MODE 2.)
Changing the modes for either the PRIMARY or TACTICAL switches:
Step 1: Press and hold the PROGRAMMING switch for two to five seconds. The Fuel Gauge
LED will illuminate BLUE to indicate programming mode.
Step 2: While holding the PROGRAMMING switch and observing the BLUE LED Fuel
Gauge, tap either the PRIMARY or TACTICAL switch once and release the
PROGRAMMING switch. Pressing the PRIMARY or TACTICAL switch more than
ONCE exits the programming mode. Once the PROGRAMMING switch is released,
the Fuel Gauge LED blinks GREEN three times for success or RED three times for error.
POCKET CLIP RELOCATION
1. Rotate T8 Torx screws counter clockwise with supplied wrench to remove the
two pocket clip screws.
2. Place pocket clip on STILETTO PRO II body in desired position.
3. Rotate T8 Torx screws clockwise with supplied wrench. Tighten screws to 1.4 inch pounds of
torque. If torque wrench is not available, tighten screws an additional 1/4 turn once resistance
is felt. DO NOT OVERTIGHTEN. The STILETTO PRO II body is die cast aluminum. If the screws
are overtightened, the screw holes can become stripped, which could void the warranty.
FUEL GAUGE LED INDICATOR
CHARGING DISCHARGING
FLASHING GREEN 98%-100% Charged -
SOLID GREEN 70-98% Charged 70-100% Capactity
SOLID YELLOW 35-69% Capacity, Charging 35-69% Capacity
SOLID RED <35% Capacity, Charging Recharge Immediately
FLASHING RED Pre-charge mode Battery Critically Low
PRIMARY
SWITCH
USB-C
PROGRAMMING
SWITCH
FUEL GAUGE LED
TACTICAL
SWITCH
STROBE WARNING
Exposure to strobing lights may cause dizziness, disorientation, and nausea. A very small
percentage of people suffer from photosensitive epilepsy—approximately .00025% of the
population—and may experience seizures or blackouts triggered by strobing lights. Visit www.
epilepsyfoundation.org for more information about this rare form of epilepsy. Anyone who has
had symptoms linked to this condition should consult a doctor before using this product.
NOTE: The PRIMARY, TACTICAL and PROGRAMMING switches will not activate the STILETTO PRO
II when Lockout Mode is enabled. The Fuel Gauge LED will blink blue when a button is pressed
while Lockout mode is enabled.
To Disable Lockout Mode:
1. Press the and PRIMARY TACTICAL switch simultaneously, then release.
NOTE: The PRIMARY, TACTICAL and PROGRAMMING switches will be instantly ready for use when
Lockout Mode is disabled.
To Enable Lockout Mode
1. Press and hold the PRIMARY and TACTICAL switch simultaneously for four seconds. The Fuel
Gauge LED will be BLUE while holding the buttons.
2. Release the buttons when the Fuel Gauge LED blinks GREEN three times to confirm Lockout
Mode is enabled. The FUEL Gauge will blink RED three times for failure to enable Lockout mode.
LOCKOUT MODE


Product specificaties

Merk: SureFire
Categorie: Zaklamp
Model: STILETTO PRO II

Heb je hulp nodig?

Als je hulp nodig hebt met SureFire STILETTO PRO II stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Zaklamp SureFire

Handleiding Zaklamp

Nieuwste handleidingen voor Zaklamp