Supermicro SuperServer F648G2-FTPT+ Handleiding

Supermicro Server SuperServer F648G2-FTPT+

Lees hieronder de 📖 handleiding in het Nederlandse voor Supermicro SuperServer F648G2-FTPT+ (160 pagina's) in de categorie Server. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/160
FatTwin®
F648G2-FT+
F648G2-FTPT+
USER’S MANUAL
Revision 1.0a
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Revision 1.0a
Release Date: July 22, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the FatTwin™
F648G2-FT+/FTPT+. Installation and maintenance should be performed by
experienced technicians only.
The FatTwin F648G2-FT+/FTPT+ is a high-end server based on the
F442BG-R2K04BP 4U rackmount chassis and a dual processor X10DRFF-iG/iTG
serverboard. All models have two serverboard nodes, each node with an IPMI
LAN port and eight (8) hot-swap 2.5" SATA3 Hard Disk Drives (HDD). The
only difference between the two server models is that the F648G2-FTPT+ has
10-Gigabit LAN ports, whereas the F648G2-FT+ only has Gigabit LAN ports.
Manual Organization
Chapter 1: Introduction
The fi rst chapter provides a checklist of the main components included with
the server system and describes the main features of the X10DRFF-iG/iTG
serverboards and the F442BG-R2K04BP chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the FatTwin F648G2-FT+/FTPT+
into a rack and check out the server confi guration prior to powering up the system.
If your server was ordered without processor and memory components, this
chapter will refer you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: Standardized Warning Statements for AC Systems
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
FatTwin F648G2-FT+/FTPT+.
FatTwin F648G2-FT+/FTPT+ User's Manual
iv
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X10DRFF-iG/iTG serverboards,
including the locations and functions of connections, headers and jumpers. Refer
to this chapter when adding or removing processors or main memory and when
reconfi guring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the F442BG-R2K04BP server chassis.
You should follow the procedures given in this chapter when installing, removing or
reconfi guring SATA or peripheral drives and when replacing system power supply
units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed information
on running the CMOS Setup Utility.
Appendix A: System Specifi cations
v
FatTwin F648G2-FT+/FTPT+ User's Manual
Notes
vi
Table of Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Serverboard Features ..................................................................................... 1-2
Processors ...................................................................................................... 1-2
Memory ........................................................................................................... 1-2
Serial ATA ....................................................................................................... 1-3
PCI Expansion Slots ....................................................................................... 1-3
Onboard Controllers/Ports .............................................................................. 1-3
Graphics Controller ......................................................................................... 1-3
Aspeed AST2400 Controller .......................................................................... 1-3
Other Features Supported by the Aspeed AST2400 Controller ................ 1-4
Power Supply .................................................................................................. 1-5
Super I/O ......................................................................................................... 1-5
1-3 Server Chassis Features ................................................................................ 1-5
System Power ................................................................................................. 1-5
SAS/SATA Subsystem ..................................................................................... 1-5
I/O Ports .......................................................................................................... 1-5
Cooling System ............................................................................................... 1-6
Air Shrouds ..................................................................................................... 1-6
Mounting Rails ................................................................................................ 1-6
1-4 Advanced Power Management ....................................................................... 1-6
Intel® Intelligent Power Node Manager (NM) ................................................. 1-6
Manageability Engine (ME) ............................................................................. 1-6
1-5 Contacting Supermicro .................................................................................... 1-8
1-6 FatTwin: System Notes ................................................................................... 1-9
Nodes .............................................................................................................. 1-9
System Power ................................................................................................. 1-9
SAS/SATA Backplane/Drives .......................................................................... 1-9
Chapter 2 Server Installation
2-1 Overview ......................................................................................................... 2-1
2-2 Unpacking the System .................................................................................... 2-1
2-3 Preparing for Setup ......................................................................................... 2-1
2-4 Warnings and Precautions .............................................................................. 2-2
Choosing a Setup Location ............................................................................. 2-2
Rack Precautions ............................................................................................ 2-2
Server Precautions .......................................................................................... 2-2
FatTwin F648G2-FT+/FTPT+ User's Manual
viii
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard ............................................................................... 5-1
Precautions ..................................................................................................... 5-1
Unpacking ....................................................................................................... 5-1
5-2 Connecting Cables .......................................................................................... 5-2
Connecting Data Cables ................................................................................. 5-2
5-3 Control Panel Connectors and I/O Ports ........................................................ 5-2
5-4 Processor and Heatsink Installation................................................................ 5-3
Installing a Passive CPU Heatsink ................................................................. 5-7
Removing the Passive Heatsink ..................................................................... 5-8
5-5 Installing Memory ............................................................................................ 5-9
Removing Memory Modules ........................................................................... 5-9
Memory Support ............................................................................................ 5-10
5-6 Serverboard Details ...................................................................................... 5-12
5-7 Connector Defi nitions .................................................................................... 5-15
5-8 Jumper Settings ............................................................................................ 5-19
Explanation of Jumpers ................................................................................ 5-19
5-9 Onboard Indicators ........................................................................................ 5-22
5-10 Serial ATA and SAS Connections ................................................................. 5-24
5-11 Installing Drivers ............................................................................................ 5-25
SuperDoctor 5 ............................................................................................... 5-26
5-12 Serverboard Battery ...................................................................................... 5-28
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices .................................................................................. 6-1
Precautions ..................................................................................................... 6-1
Unpacking ....................................................................................................... 6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 Removing the Power Cord .............................................................................. 6-3
6-4 Removing Nodes from the Chassis ................................................................ 6-3
6-5 Installing and Removing Hard Drives ............................................................. 6-4
Removing Hard Drives from the Front of the Node ........................................ 6-5
Installing 2.5" Hard Drives into the Drive Carriers .......................................... 6-6
6-6 Node Confi guration ......................................................................................... 6-8
Overview of the Node ..................................................................................... 6-8
6-7 Removing the Node Cover.............................................................................. 6-9
6-8 Removing and Installing the Backplane ........................................................ 6-10
Removing the Backplane .............................................................................. 6-10
Installing the Backplane .................................................................................6-11
6-9 Power Adapter Board Replacement .............................................................. 6-12
FatTwin F648G2-FT+/FTPT+ User's Manual
6-10 Installing the Serverboard ............................................................................ 6-16
Compatible Motherboards ............................................................................. 6-16
Permanent and Optional Standoffs ............................................................... 6-16
6-11 Installing Front and Rear Expansion Cards .................................................. 6-18
PCI-E Slot Setup ........................................................................................... 6-18
Installing an Expansion Card ........................................................................ 6-19
6-12 Installing Internal GPUs ................................................................................ 6-20
Installing Front GPUs into the GPU Bracket ............................................... 6-20
Installing a Front GPU into the Node .......................................................... 6-21
Preparation Before Installing Rear GPUs into the Node ............................. 6-21
Installing the Rear GPU into the Node ........................................................ 6-22
6-13 Installing the Air Shrouds .............................................................................. 6-23
Air Shrouds ................................................................................................... 6-23
6-14 Checking the Airfl ow .................................................................................... 6-24
Installation Complete ..................................................................................... 6-24
6-15 Replacing Exhaust Fans ............................................................................... 6-25
6-16 Replacing the Power Supply ......................................................................... 6-26
Power Supply Replacement .......................................................................... 6-26
Chapter 7 BIOS
7-1 Introduction ...................................................................................................... 7-1
Starting BIOS Setup Utility .............................................................................. 7-1
How To Change the Confi guration Data ......................................................... 7-1
Starting the Setup Utility ................................................................................. 7-2
7-2 Main Setup ...................................................................................................... 7-2
7-3 Advanced Setup Confi gurations...................................................................... 7-3
7-4 Event Logs .................................................................................................... 7-41
7-5 IPMI ............................................................................................................... 7-43
7-6 Security Settings ........................................................................................... 7-45
7-7 Boot Settings ................................................................................................. 7-46
7-8 Save & Exit ................................................................................................... 7-48
Appendix A System Specifi cations
ix
Table of Contents
x
Notes
FatTwin F648G2-FT+/FTPT+ User's Manual
Chapter 1
Introduction
1-1 Overview
The FatTwin F648G2-FT+/FTPT+ is a high-end server comprised of two main
subsystems: the F442BG-R2K04BP 4U server chassis and the X10DRFF-iG/iTG
dual processor serverboard in two hot-swap nodes. Please refer to our web site for
information on operating systems that have been certifi ed for use with the system
(www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the SuperServer F648G2-FT+/FTPT+ server, as listed below:
• Four (4) 2U passive CPU heat sinks with Narrow ILM (SNK-P0048PS)
• Power Adapter:
Four (4) power backplanes for GPU (BPN-ADP-4UGPU-P)
Four (4) power backplanes (BPN-ADP-F418L)
• SAS/SATA Backplane and accessories:
Two (2) HDD backplanes (BPN-SAS-I28A)
Sixteen (16) 2.5" HDD hot swap trays (MCP-220-00090-0B)
Four (4) cross-over Ipass to four SATA, 30AWG, HF, RoHS/REACH, PBF
data cables (CBL-SAST-0583)
• Two (2) 8-pin to 2x4-pin (35-cm and 22-cm) 18AWG, HF, RoHS/REACH, PBF
power cables (CBL-PWEX-0460-05)
• Riser Cards:
Two (2) PCI-E 3.0 x16 riser cards (RSC-R2UFF-X2E16B)
Two (2) PCI-E 3.0 x16 riser cards (RSC-R4UFF-A2E16A)
Two (2) PCI-E 3.0 x16 riser cards (RSC-R4UFF-A4E16B)
• One (1) F418/F424 rail set (MCP-290-41803-0N)
Note: For use with the PWS-2K04A-1R power supply you will need to use the C13
to C14 size 14AWG wire power cord set (14AWG/250V/15A, 3FT) for the rack.
Chapter 1: Introduction
1-1
1-2
FatTwin F648G2-FT+/FTPT+ User's Manual
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
• Supermicro product manuals: http://www.supermicro.com/support/manuals/
• Product drivers and utilities: ftp://ftp.supermicro.com
• Product safety information:
http://www.supermicro.com/about/policies/safety_information.cfm
• If you have any questions, please contact our support team at:
support@supermicro.com
1-2 Serverboard Features
At the heart of the FatTwin F648G2-FT+/FTPT+ lies the X10DRFF-iG/iTG, a
dual processor serverboard based on the Intel® C612 chipset and designed to
provide maximum performance. Two of these serverboards can be mounted in the
F442BG-R2K04BP chassis.
The sections below cover the main features of the X10DRFF-iG/iTG serverboard
(see Figure 1-1 for a block diagram of the chipset).
Processors
The X10DRFF-iG/iTG supports single or dual Intel® Xeon® E5-2600 v3/v4 family
processors (Socket R3 LGA 2011). Each processor supports four full-width Intel
QuickPath Interconnect (QPI) links, with support of up to 25.6 GT/s per QPI link
and with Data Transfer Rate of up to 9.6 GT/s per direction. Please refer to the
serverboard description pages on our web site for a complete listing of supported
processors (www.supermicro.com).
Memory
Each X10DRFF-iG/iTG serverboard node has sixteen (16) DIMM slots supporting
up to 2 TB of 3DS LRDIMM registered ECC or up to 1 TB of RDIMM ECC at
DDR4-2400/2133/1866/1600 MHz speeds and up to 1 GB, 2 GB, 4 GB, 8 GB, 16
GB, 32 GB, 64 GB and 128 GB (3DS LRDIMM only) sizes at 1.2V voltage. See
Chapter 5 for details.
Note: For the latest CPU/memory updates, please refer to our website at
http://www.supermicro.com/products/serverboard.
1-3
Chapter 1: Introduction
Serial ATA
A Serial ATA controller is integrated into the C612 to provide up to ten (10) SATA
3.0 connections, including six (6) SATA 3.0 ports supported by Intel PCH (I-SATA
0-5) and four (4) SATA 3.0 with 4 connections supported by the PCH (S-SATA 0-3) .
These drives support RAID 0, 1, 5 and 10 capability. The SATA drives are hot-
swappable units.
Note: The operating system you use must have RAID support to enable the hot-
swap capability and RAID function of the SATA drives.
PCI Expansion Slots
Each node in the FatTwin F648G2-FT+/FTPT+ server has the following available
PCI-E slots for the node:
• 2x PCI-E 3.0 x8 full-height, half-length slots
• 6x PCI-E 3.0 x16 double-width GPU/Xeon PHi slots
Onboard Controllers/Ports
One Fast UART 16550 serial port is located on the serverboard. The I/O ports
include one VGA (monitor) port, two USB 3.0 ports, an IPMI dedicated LAN port
and either two Gigabit or two 10GBased-T Ethernet ports.
Note: For IPMI Confi guration Instructions, please refer to the Embedded IPMI
Configuration User's Guide available at http://www.supermicro.com/support/
manuals/.
Graphics Controller
The X10DRFF-iG/iTG features an integrated Aspeed AST2400 BMC Controller for
onboard graphics capability.
Aspeed AST2400 Controller
Note: The term "IPMI controller" and the term "BMC controller" can be used
interchangeably in this section.
The Aspeed AST2400 Controller, a Baseboard Management Controller (BMC),
supports 2D/VGA-compatible Graphic Cores with PCI interface, creating multi-media
virtualization via Keyboard/Video/Mouse Redirection (KVMR). The WPCM450R
Controller is ideal for remote system management.
1-5
Chapter 1: Introduction
Power Supply
Please connect the power cable from the SMC-Proprietary Adaptor (BPN-ADP-
F418L) to the serverboard in order to provide power to the system.
Super I/O
The Super I/O provides functions that comply with ACPI (Advanced Confi guration
and Power Interface), which includes support of legacy and ACPI power
management through an SMI or SCI function pin. It also features auto power
management to reduce power consumption.
1-3 Server Chassis Features
The following is a general outline of the main features of the F442BG server chassis.
System Power
The F442BG chassis model includes four high-effi ciency 1 + 1 Titanium Level
(96%+) redundant 2000 Watt power supplies (PWS-2K04A-1R). In the unlikely
event your power supply fails, replacement is simple and can be accomplished
without tools.
Note: The power supplies are both redundant, hot-plug.
SAS/SATA Subsystem
The F442BG supports up to eight SAS/SATA HDD drives. These drives are hot
swapable units and are connected to two backplanes (that provides power and
control) per node.
Note: For more information, visit our Web site at: http://www.supermicro.com.
I/O Ports
The F442BG is an proprietary form factor chassis designed to be used in a 4U
rackmount confi guration. The F442BG chassis provides two x8 half-length add-on
card slots, a VGA port, two USB 3.0 ports, one IPMI Ethernet port and two gigabit
(F648G2-FT+) or two 10G (F648G2-FTPT+) Ethernet ports per node.
1-6
FatTwin F648G2-FT+/FTPT+ User's Manual
Cooling System
The F442BG chassis supports external exhaust fans that provide cooling for the
system. The F648G2-FT+/FTPT+ server uses eight (8) 8-cm external system
fans powered from either the backplane or the serverboards. When one of the
serverboard nodes is removed, another serverboard will continue to operate the
fans.
Note: The fans in this system are redundant, hot-plug.
Air Shrouds
The F442BG chassis requires mylar air shrouds for each node to direct the airfl ow
where cooling is needed. The air shroud will differ for different motherboards. If
using a serverboard which is not the default in the chassis, refer to the Supermicro
Web site at www.supermicro.com to purchase the proper air shroud.
Mounting Rails
The F442BG includes a set of rails, and can be placed in a rack for secure storage
and use. To setup your rack, follow the step-by-step instructions included in this
manual.
1-4 Advanced Power Management
Intel® Intelligent Power Node Manager (NM)
The Intel® Intelligent Power Node Manager (IPNM) provides your system with
real-time thermal control and power management for maximum energy effi ciency.
Although IPNM Specifi cation Version 1.5 is supported by the BMC (Baseboard
Management Controller), your system must also have IPNM-compatible
Manageability Engine (ME) fi rmware installed to use this feature.
Manageability Engine (ME)
The Manageability Engine, which is an ARC controller embedded in the IOH (I/O
Hub), provides Server Platform Services (SPS) to your system. The services
provided by SPS are different from those provided by the ME on client platforms.
1-7
Chapter 1: Introduction
Figure 1-1. Intel C612 Chipset:
System Block Diagram
Note: This is a general block diagram and may not exactly repre-
sent the features on your serverboard. See the previous pages for
the actual specifi cations of your serverboard. This block diagram is
intended for your reference only.
SPI
LAN3
RGRMII
Debug Card
FRONT PANEL
SYSTEM POWER
CTRL
FAN SPEED
PCI-E X1 G2
USB 2.0
X10DRFF-iG Rev. 1.00
PCH
6.0 Gb/S
LPC
SATA
RTL8211E
-VB-CG
RJ45
BIOS
SPI
SPI
Temp Sensor
EMC1402-1 *2 at di SMBUS
TPM HEADER
USB 3.0
USB
BIOS
HEADER
SPI
AST2400
BMC
RMII/NCSI
COM1
VGA CONN
BMC
Boot Flash
DDR3
5 PHASE
145W
P1
P1
P0
VR12.5
P0
QPI
9.6G
DMI2
PCI-E X16 G3
DMI2 DMI2
SNB CORE
DDR4
SNB CORE
DDR4
QPI
9.6G
5 PHASE
145W
VR12.5
#3
I350/
X540
LAN
PCI-E X8
SBX2 PCI-E X16 X16 Proprietary Slot
SLOT2 PCI-E x8
PCI-E X8 G3
PCI-E X16 G3
PCI-E X16 G3
#1
#2-8
SXB1; PCI-E X16 Proprietary Slot
PCI-E X8 G3
Slot1 PCI-E X8
SLOT3 PCI-E X4 in X8
PCI-E X4 G2
LSI3008
SAS3
PCI-E X8 G3
Port 4-7
AHCI
SCU
6.0 Gb/S
#2 #3A #1 #2 #3
CPU1 CPU2
#2-7
#2-6
#2-5
#2-4
#2-3
#2-2
1600/2133
DDR4
#2-1
1600/2133
DDR4
#1-4
#1-3
#1-2
#1-1
#1-5
#1-6
#1-7
#1-8
Header
Mini SAS
Port 0-3
0-5
SATA
0-3
RJ45
RJ45
HD
Mini SAS
HD
1-9
Chapter 1: Introduction
1-6 FatTwin: System Notes
As a FatTwin confi guration, the FatTwin F648G2-FT+/FTPT+ is a unique server
system. With two system boards incorporated into a single chassis acting as two
separate nodes, there are several points you should keep in mind.
Nodes
Each of the two serverboards act as a separate node in the system. As independent
nodes, each may be powered off and on without affecting the other. In addition, each
node is a hot-swappable unit that may be removed from the front of the chassis.
The nodes are connected to the server backplane by means of an adapter card.
Note: A guide pin is located on the inner chassis wall. This guide pin also acts as
a “stop” when a node is fully installed. If too much force is used when inserting a
node this pin may break off. Take care to slowly slide a node in until you hear the
“click” of the locking tab seating itself.
System Power
Four high-effi ciency 96%+ Plus Titanium Level 2000 Watt power supplies are used
to provide the power for all serverboards. Each serverboard however, can be shut
down independently of the other with the power button on its own control panel.
SAS/SATA Backplane/Drives
As a system, the FatTwin F648G2-FT+/FTPT+ supports the use of up to eight (8)
drives per node. See Chapter 6 for the logical hard drive and node confi guration.
1-10
FatTwin F648G2-FT+/FTPT+ User's Manual
Notes
Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provid es a quick s etup checklist to get your FatTwin
F648G2-FT+/FTPT+ up and running. Following these steps in the order given
should enable you to have the system operational within a minimum amount
of time. This quick setup assumes that your system has come to you with
the processors and memory pre-installed. If your system is not already fully
integrated with a serverboard, processors, system memory etc., then please
turn to the chapter or section noted in each step for details on installing specific
components.
2-2 Unpacking the System
You should inspect the box the FatTwin F648G2-FT+/FTPT+ was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
fi le a damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the FatTwin
F648G2-FT+/FTPT+. It should be situated in a clean, dust-free area that is well
ventilated. Avoid areas where heat, electrical noise and electromagnetic fi elds are
generated. You will also need it placed near a grounded power outlet. Read the
Rack and Server Precautions in the next section.
2-3 Preparing for Setup
The box the FatTwin F648G2-FT+/FTPT+ was shipped in should include two sets
of rail assemblies, two rail mounting brackets and the mounting screws you will
need to install the system into the rack. Follow the steps in the order given to
complete the installation process in a minimum amount of time. Please read this
2-4
FatTwin F648G2-FT+/FTPT+ User's Manual
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack
itself should be grounded. Particular attention should be given to power supply
connections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).
2-5 Rack Mounting Instructions
This section provides information on installing the chassis into a rack unit with the
rails provided. There are a variety of rack units on the market, which may mean that
the assembly procedure will differ slightly from the instructions provided. You should
also refer to the installation instructions that came with the rack unit you are using.
Note: This rail will fi t a rack between 26.5" and 36.4" deep. The F442BG is not
designed for installation into a Telco post-style rack unit.
Warning: Do not pick up the server with the front handles. They are designed
to pull the system from a rack only.
Stability Hazard: The rack stabilizing mechanism must be in place, or the
rack must be bolted to the fl oor before you slide the unit out for servicing. Failure to
stabilize the rack can cause the rack to tip over.
Warning: Slide rail mounted equipment is not to be used as a shelf or a work
space.
Warning: When initially installing the server to a rack, test that the rail locking tabs
engage to prevent the server from being overextended. Have a rack lift in place as
a precaution in case the test fails.
Warning: In any instance of pulling the system from the rack, always use a rack
lift and follow all associated safety precautions.
Identifying the Sections of the Rack Rails
The chassis package includes two rail assemblies in the rack mounting kit. Each
assembly consists of two sections: A front section which secures to the front post
of the rack and a rear section which adjusts in length and secures to the rear post
of the rack. These assemblies are specifi cally designed for the left and right side
of the chassis (see Figure 2-1).
Chapter 2: Server Installation
2-5
Figure 2-1: Identifying the Outer Rail and Inner Rails
(Left Rail Assembly Shown)
Inner Rail
This Side Faces
Outward
Adjusting Screw
Outer Rail
Adjusting the Rails
Each rail assembly has an adjusting screw. Loosening this screw allows you to
adjust the length of the rail to fi t a variety of rack sizes.
2-6
FatTwin F648G2-FT+/FTPT+ User's Manual
Installing the Rails on a Rack
Installing the Rails
1. Adjust the length of both rails as described on the previous page.
2. Align the front section of the outer rail with the slots on the front post of the
rack. Secure the front of the outer rail to the rack with two screws.
3. Pull out the rear section of the outer rail, adjusting the length until it fi ts within
the posts of the rack.
4. Align the rear section of the rail with the slots on the rear post of the rack.
Secure the rear of the outer rail to the rear of the rack with two screws.
5. Repeat steps 1-4 for the remaining rail.
Figure 2-2: Attaching the Rails to a Rack
Chapter 2: Server Installation
2-7
Note: The fi gure above is for illustration purposes only. Always install servers to
the bottom of the rack fi rst.
Figure 2-3: Installing into a Rack
Chassis Installation
Installing the Chassis into a Rack
1. Confi rm that the rails are correctly installed on the rack.
2. Align the bottom of the chassis with the bottom of the rails.
3. Insert the chassis into the rails, keeping the pressure even on both sides,
pushing the chassis into the rack.
4. Secure the chassis handles to the front of the rack.
2-8
FatTwin F648G2-FT+/FTPT+ User's Manual
2-6 Checking the Serverboard Setup
After you install the SuperServer F648G2-FT+/FTPT+ in the rack, you will need
to open the unit to make sure the serverboard is properly installed and all the
connections have been made.
Accessing the inside of the System
Before operating the server for the fi rst time, it is important to remove the protective
fi lm covering the top of the chassis, in order to allow for proper ventilation and
cooling.
Warning: Except for short periods of time, do NOT operate the server without
the cover in place. The chassis cover must be in place to allow proper airfl ow
and prevent overheating.
Checking the Components and Setup
1. You may have one or two processors already installed into the serverboard.
Each processor needs its own heat sink. See Chapter 5 for instructions on
processor and heat sink installation.
2. Your SuperServer F648G2-FT+/FTPT+ server system may have come with
system memory already installed. Make sure all DIMMs are fully seated in
their slots. For details on adding system memory, refer to Chapter 5.
3. If desired, you can install add-on cards to the system. See Chapter 5 for
details on installing PCI add-on cards.
4. Make sure all power and data cables are properly connected and not blocking
the chassis airfl ow. Also make sure that no cables are positioned in front of
the fans. See Chapter 5 for details on cable connections.
Chapter 2: Server Installation
2-9
2-7 Checking the Drive Bay Setup
Next, you should check to make sure the peripheral drives and the SATA drives
have been properly installed and all connections have been made.
Checking the Drives
1. All drives are accessible from the front of the server. A hard drive can be
installed and removed from the front of the chassis without removing the top
chassis cover.
2. Depending upon your system's confi guration, your system may have one or
more drives already installed. If you need to install hard drives, please refer to
Chapter 6.
Checking the Airfl ow
1. Make sure there are no objects to obstruct airfl ow in and out of the server. In
addition, if you are using a front bezel, make sure the bezel's fi lter is replaced
periodically.
2. Do not operate the server without drives or drive trays in the drive bays. Use
only recommended server parts.
3. Make sure that no wires or foreign objects obstruct air fl ow through the
chassis. Pull all excess cabling out of the airfl ow path or use shorter cables.
The control panel LEDs inform you of the system status. See “Chapter 3
System Interface” for details on the LEDs and the control panel buttons.
Providing Power
1. Plug the power cord(s) from the power supply unit(s) into a high-quality
power strip that offers protection from electrical noise and power surges. It is
recommended that you use an uninterruptible power supply (UPS).
2. Depress the power on button on the front of the chassis.
2-10
FatTwin F648G2-FT+/FTPT+ User's Manual
Notes
Chapter 3: System Interface
3-1
Chapter 3
System Interface
3-1 Overview
There are several LEDs on the control panel to keep you constantly informed of
the overall status of the system. The F442BG model includes two control panels,
which control each of the systems.
This chapter explains the meanings of all LED indicators and the appropriate re-
sponse you may need to take.
3-3 F442BG Front I/O Control Panel
The F442BG chassis include a power button with a built-in LED and features both
a LAN LED and a UID LED on each node's front control panel.
Figure 3-1: F442BG Node Control Panel
(Your chassis and drives may differ from those shown in this illustration)
FatTwin F648G2-FT+/FTPT+ User's Manual
3-2
Power
The main power button on each of the two control panels is used to apply or remove
power from the power supply to each of the two systems in the chassis. Turning off
system power with this button removes the main power, but keeps standby power
supplied to the system. Therefore, you must unplug system before servicing. The
power button has a built-in LED which will turn green when the power is on.
UID
When used with a UID compatible serverboard, the UID button is used to turn on
or off the blue light function of the LED. This is built into the front side of the UID
button and at the rear end of each serverboard node, for those motherboards which
support it. Once the blue light is activated, the unit can be easily located in very
large racks and server banks.
3-3 Drive Carrier LEDs
The chassis includes externally accessible SAS/SATA drives. Each drive carrier
displays two status LEDs on the front of the carrier.
LED Color State Status
Activity LED Green Solid On SAS drive installed
Green Blinking I/O activity
Status LED Red Solid On Failed drive for SAS/SATA with RSTe
support
Red Blinking at 1 Hz Rebuild drive for SAS/SATA with RSTe
support
Red Blinking with two blinks
and one stop at 1 Hz
Hot spare for SAS/SATA with RSTe
support
Red On for fi ve seconds,
then o
Power on for SAS/SATA with RSTe
support
Red Blinking at 4 Hz Identify drive for SAS/SATA with RSTe
support
4-1
Chapter 4: Warning Statements for AC Systems
Chapter 4
Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certifi ed technicians should attempt to install or confi gure
components.
Read this appendix in its entirety before installing or confi guring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning Defi nition
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
警告の定義
この警告サインは危険を意味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分
意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸
電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。
4-3
Warning Statements for AC Systems
안전을 위한 주의사항
경고!
이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준 작업절차를
준수해 주시기 바랍니다.
해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
. ﻲﻓ ﻚﻧا نأ ﻦﻜﻤﯾ ﺔﻟﺎﺣ ﻲﻓ ﺐﺒﺴﺘﺗ ﺔﺑﺎﺻا ﺔﯾﺪﺴﺟ ﺰﻣﺮﻟا اﺬھ ﻲﻨﻌﯾ ﺮﻄﺧ !ﺮﯾﺬﺤﺗ
نأ ﻞﺒﻗ يأ ﻰﻠﻋ ﻞﻤﻌﺗ تاﺪﻌﻣ،ﻛﻢﻠﻋ ﻰﻠﻋ ﻦ ﻦﻋ ﺔﻤﺟﺎﻨﻟا ﺮطﺎﺨﻤﻟﺎﺑ ﺮﺋاوﺪﻟا
ﺔﯿﺋﺎﺑﺮﮭﻜﻟا
ﻛوﺔﯾارد ﻰﻠﻋ ﻦ رﺎﻤﻤﻟﺎﺑتﺎﺳ ﺔﯿﺋﺎﻗﻮﻟا ﻟ ﻊﻨﻤعﻮﻗو يأثداﻮﺣ
ﻢﻗر مﺪﺨﺘﺳا نﺎﯿﺒﻟا صﻮﺼﻨﻤﻟا ﺔﯾﺎﮭﻧ ﻲﻓ ﺮﯾﺬﺤﺗ ﻞﻛ رﻮﺜﻌﻠﻟ ﺎﮭﺘﻤﺟﺮﺗ
4-4
FatTwin F648G2-FT+/FTPT+ User's Manual
Installation Instructions
Warning!
Read the installation instructions before connecting the system to the power source.
設置手順書
システムを電源に接続する前に、設置手順書をお読み下さい。
警告
将此系统连接电源前,请先阅读安装说明。
警告
將系統與電源連接前，請先閱讀安裝說明。
Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen
lesen.
¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives
d'installation.
ﻟا تادﺎﺷرإ ﺮﻗاﺐﯿﻛﺮﺘ ﻞﯿﺻﻮﺗ ﻞﺒﻗ ﻰﻟإ مﺎﻈﻨﻟا ﺔﻗﺎﻄﻠﻟ رﺪﺼﻣ
אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.
시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron
aansluit.
4-6
FatTwin F648G2-FT+/FTPT+ User's Manual
Power Disconnection Warning
Warning!
The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.
電源切断の警告
システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス
するには、
システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り
外す必要があります。
警告
在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。
警告
在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。
경고!
이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지
않도록 해야 합니다.
Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische
installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan
220V, 20A.
ﺞﺘﻨﻤﻟا اﺬھ ﻰﻠﻋ ﺪﻤﺘﻌﯾ تاﺪﻌﻣ ﺔﯾﺎﻤﺤﻟا ةﺮﯿﺼﻘﻟاﺮﺋاوﺪﻟا ﻦﻣ ﺎﮭﺘﯿﺒﺜﺗ ﻢﺗ ﻲﺘﻟا ﻲﻓ
ﻰﻨﺒﻤﻟا
20A, 250V : ﻦﻣ ﺪﻛﺄﺗ نأ ﻢﯿﯿﻘﺗ زﺎﮭﺠﻟا ﻟاﻲﺋﺎﻗﻮ ﺲﯿﻟ ﻦﻣ ﺮﺜﻛأ
4-8
FatTwin F648G2-FT+/FTPT+ User's Manual
Equipment Installation
Warning!
Only trained and qualifi ed personnel should be allowed to install, replace, or service
this equipment.
機器の設置
トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可
されています。
警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。
警告
只有經過受訓且具資格人員才可安裝、更換與維修此設備。
Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,
qualifi ziertem Personal gestattet werden.
¡Advertencia!
Solamente el personal califi cado debe instalar, reemplazar o utilizar este equipo.
Attention
Il est vivement recommandé de confier l'installation, le remplacement et la
maintenance de ces équipements à des personnels qualifi és et expérimentés.
!הרהזא
שר דבלב ךמסומ תווצתא ףילחהל ,ןיקתהל יא . דויצה רובע תוריש תתל וא דויצה
ﻦﯿﺑرﺪﻤﻟاو و ﺐﯿﻛﺮﺘﻟلاﺪﺒﺘﺳا وأ ﺔﻣﺪﺧ زﺎﮭﺠﻟا اﺬھ ﺢﻤﺴﯾ نأ ﺐﺠﯾ ﻂﻘﻓ ﻦﯿﻠھﺆﻤﻟا ﻦﯿﻔظﻮﻤﻠﻟ
경고!
훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수
있습니다.
4-9
Chapter 4: Warning Statements for AC Systems
Restricted Area
Warning!
This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).
アクセス制限区域
このユニットは、アクセス制限区域に設置されることを想定しています。
アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いての
み出入りが可能です。
警告
此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和
钥匙或其它安全手段进出的场所。
警告
此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙
或其他安全方式才能進入的區域。
Warnung
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.
Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.
¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.
Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.
Attention
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une
zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.
Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door
geschoold en gekwali ceerd personeel.
4-10
FatTwin F648G2-FT+/FTPT+ User's Manual
Battery Handling
Warning!
There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、または同等のものを使用下さい。使用済電池は製造元の指示に従
って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
תלבגומ
תלבגומ
תלבגומ
תלבגומתלבגומ השיג
השיג
השיג
השיגהשיג םע
םע
םע
םעםע רו
רו
רו
רורו
!
!
!
!!הרהזא
הרהזא
הרהזא
הרהזאהרהזא
. תרזעב תנתינ השיגה השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתה
.('דכו לוענמ ,חתפמ) דבלב החטבא ילכ
. ﺺﯿﺼﺨﺗ ةﺪﺣﻮﻟا هﺬھ ﻲﻓ ﺎﮭﺒﯿﻛﺮﺘﻟ ﻖطﺎﻨﻣ ةرﻮﻈﺤﻣ ﻢﺗ
ﺻﻮﻟا ﻦﻜﻤﯾﻰﻟإ لﻮ ﺔﻘﻄﻨﻣ ةرﻮﻈﺤﻣ ﻂﻘﻓ ماﺪﺨﺘﺳا لﻼﺧ ﻦﻣ ،ﺔﺻﺎﺧ ةادأ
وأ يأ ﻼﻟ ىﺮﺧأ ﺔﻼﯿﺳونﺎﻣﻷ حﺎﺘﻔﻣو ﻞﻔﻗ
경고!
이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치
및 키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.
Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.
Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.
4-11
Chapter 4: Warning Statements for AC Systems
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.
!
!
!
!!הרהזא
הרהזא
הרהזא
הרהזאהרהזא
תנכס תמייקץוציפ . הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי
גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.
תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל
ﺮﻄﺧ كﺎﻨھ ﻦﻣ لاﺪﺒﺘﺳا ﺔﻟﺎﺣ ﻲﻓ رﺎﺠﻔﻧا ﺔﯾرﺎﻄﺒﻟا ﺔﺤﯿﺤﺻ ﺮﯿﻏ ﺔﻘﯾﺮﻄﺑ ﻚﯿﻠﻌﻓ ﺔﯾرﺎﻄﺒﻟا لاﺪﺒﺘﺳا
ﻂﻘﻓ عﻮﻨﻟا ﺲﻔﻨﺑ ﺎﮭﻟدﺎﻌﯾ ﺎﻣ وأ ﺎﻤﻛﺖﺻوأ ﺔﻌﻨﺼﻤﻟا ﺔﻛﺮﺸﻟا ﮫﺑ
تﺎﯾرﺎﻄﺒﻟا ﻦﻣ ﺺﻠﺨﺗ ﻟ ﺎﻘﻓو ﺔﻠﻤﻌﺘﺴﻤﻟاﺔﻌﻧﺎﺼﻟا ﺔﻛﺮﺸﻟا تﺎﻤﯿﻠﻌﺘ
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Waarschuwing
Er is ontploffi ngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.
4-12
FatTwin F648G2-FT+/FTPT+ User's Manual
Redundant Power Supplies
Warning!
This unit might have more than one power supply connection. All connections must
be removed to de-energize the unit.
冗長電源装置
このユニットは複数の電源装置が接続されている場合があります。
ユニットの電源を切るためには、すべての接続を取り外さなければなりません。
警告
此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。
警告
此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。
Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass
der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.
¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación.
Para cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.
Attention
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute
tension et tout courant électrique de l'unité, toutes les connexions d'alimentation
doivent être débranchées.
דחא
דחא
דחא
דחאדחא קפסמ
קפסמ
קפסמ
קפסמקפסמ רתוי
רתוי
רתוי
רתוירתוי םייק
םייק
םייק
םייקםייק םא
םא
םא
םאםא
!
!
!
!!הרהזא
הרהזא
הרהזא
הרהזאהרהזא
. קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שי ןקורל תנמ לע םירוביחה לכ
חיה תאי.הד
4-13
Chapter 4: Warning Statements for AC Systems
Backplane Voltage
Warning!
Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.
バックプレーンの電圧
システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。
修理する際には注意ください。
警告
当系统正在进行时，背板上有很危险的电压或能量，进行维修时务必小心。
警告
當系統正在進行時，背板上有危險的電壓或能量，進行維修時務必小心。
Warnung
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche
Spannungen oder Energien auf. Vorsicht bei der Wartung.
¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.
Tenga cuidado cuando lo revise.
.ﺪﻗ اﺬﮭﻟ نﻮﻜﯾ ﻟازﺎﮭﺠ تﻻﺎﺼﺗا ةﺪﻋ تاﺪﺣﻮﺑ ﺔﻗﺎﻄﻟا داﺪﻣا
ﺔﻟازإ ﺐﺠﯾ تﻻﺎﺼﺗﻻا ﺔﻓﺎﻛ لﺰﻌﻟ ﻟاةﺪﺣﻮ ﻦﻋ ءﺎﺑﺮﮭﻜﻟا
경고!
이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.
Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle
aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.
4-15
Chapter 4: Warning Statements for AC Systems
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
製品の廃棄
この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
יצראה
יצראה
יצראה
יצראהיצראה למשחה
למשחה
למשחה
למשחהלמשחה יקוח
יקוח
יקוח
יקוחיקוח םואית
םואית
םואית
םואיתםואית
!הרהזא
תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה.
تاﺪﻌﻤﻟا ﺐﯿﻛﺮﺗ ﺔﯿﺋﺎﺑﺮﮭﻜﻟا ﻠﻟ ﻞﺜﺘﻤﯾ نأ ﺐﺠﯾ ﻦﯿﻧاﻮﻘﺔﯿﻨطﻮﻟاو ﺔﯿﻠﺤﻤﻟا ﺔﻘﻠﻌﺘﻤﻟا ءﺎﺑﺮﮭﻜﻟﺎﺑ
¡Advertencia!
La instalacion del equipo debe cumplir con las normas de electricidad locales y
nacionales.Attention
L'équipement doit être installé conformément aux normes électriques nationales
et locales.
경고!
현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.
Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale
elektriciteitsvoorschriften.
4-16
FatTwin F648G2-FT+/FTPT+ User's Manual
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y
reglamentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.
Hot Swap Fan Warning
Warning!
The fans might still be turning when you remove the fan assembly from the chassis.
Keep fi ngers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.
ファン・ホットスワップの警告
シャーシから冷却ファン装置を取り外した際、ファンがまだ回転している可能性があり
ます。ファンの開口部に、指、ドライバー、およびその他のものを近づけないで下さい。
警告
רצומה
רצומה
רצומה
רצומהרצומה קוליס
קוליס
קוליס
קוליסקוליס
!הרהזא
ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס. הנידמה יקוח
ﻲﺋﺎﮭﻨﻟا ﺺﻠﺨﺘﻟا ﻦﻣ ﺞﺘﻨﻤﻟا اﺬھ ﮫﻌﻣ ﻞﻣﺎﻌﺘﻟا ﻲﻐﺒﻨﯾ ﻟ ﺎﻘﻓو ﻊﯿﻤﺠﺔﯿﻨطﻮﻟا ﺢﺋاﻮﻠﻟاو ﻦﯿﻧاﻮﻘﻟا ﺪﻨﻋ
경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
4-17
Chapter 4: Warning Statements for AC Systems
!הרהזא
יקלח תא רשאכ םיריסמ שי .םידבוע ןיידע םיררוואמהו ןכתי ,זראמהמ ררוואמה
קיחרהללררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה חוטב תא קחרמ
ﻦﻜﻤﻤﻻا ﻦﻣ حواﺮﻤﻻا نأ لاﺰﺗ ﻻ ﺔﻻازإ ﺪﻨﻋروﺪﺗ ﺔﻠﺘﻛ ﺔﺣوﺮﻤﻻا ﻞﻜﯿﮭﻻا ﻦﻣ ﺐﺠﯾ ءﺎﻘﺑإ
ﻊﺑﺎﺻﻷا وﻲﻏاﺮﺒﻻا تﺎﻜﻔﻣ
.ءﺎﯿﺷﻷا ﻦﻣ ﺎھﺮﯿﻏو اﺪﯿﻌﺑ ﻦﻋ تﺎﺤﺘﻔﻻا ﻲﻓ ﺔﻠﺘﻛ ﺔﺣوﺮﻤﻻا
경고!
섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬
조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 주십시오.
当您从机架移除风扇装置，风扇可能仍在转动。小心不要将手指、螺丝起子和其他
物品太靠近风扇
警告
當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他
物品太靠近風扇。
Warnung
Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis
genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.
¡Advertencia!
Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador
del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador
Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez
le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.
4-19
Chapter 4: Warning Statements for AC Systems
¡Advertencia!
Al instalar el producto, utilice los cables de conexión previstos o designados, los
cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certifi cados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.
Attention
Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.
L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certifi és qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.
אתמו
אתמו
אתמו
אתמואתמו םיילמשח
םיילמשח
םיילמשח
םיילמשחםיילמשח
מ
מ
מ
ממ
י
י
י
יי
AC
!הרהזא
םימאתמו , םיקפס םילבכב שמתשהל שי ,רצומה תא םיניקתמ רשאכ
AC רשא
וא הלקתל םורגל לוכי רחא םאתמ וא לבכ לכב ךכ שומיש . םשל וקפוסו ודעונ
טב יקוחו למשח ירישכמב שומיש יפ ילמשח יקוח לע . רצק רוסיא םייק ,תוחי
ב םיכמסומה םילבכב שמתשהל-
UL ב וא- CSA לש דוק םהילע )עיפומ ראשכ
UL/CSA( רחא ילמשח רצומ לכ רובע.דבלב ורקימקרפוס ידי לע ןיוצ אלש
ﺐﯿﻛﺮﺗ ﺪﻨﻋ ماﺪﺨﺘﺳا ﺐﺠﯾ زﺎﮭﺠﻻا و،ﻞﯿﺻﻮﺘﻻا تﻼﺑﺎﻛ ﺔﯿﺋﺎﺑﺮﮭﻜﻻا تﻼﺑﺎﻜﻻا
تﻻﻮﺤﻣو ددﺮﺘﻤﻻا رﺎﯿﺘﻻا
. نأ يأ ماﺪﺨﺘﺳا تﻼﺑﺎﻛ تﻻﻮﺤﻣو ىﺮﺧأ ﺐﺒﺴﺘﯾ ﻲﻓ ﻞﻄﻋ ثوﺪﺣ ﻖﯾﺮﺣ وأ ﻲﺘﻻا .
ﻚﻻ ﺎھﺮﯿﻓﻮﺗ ﻢﺗ ﺞﺘﻨﻤﻻا ﻊﻣ
UL وأ CSA ﺔﯿﺋﺎﺑﺮﮭﻜﻻا ةﺰﮭﺟﻷا داﻮﻣو نﻮﻧﺎﻗ ﺔﻣﻼﺴﻻا ماﺪﺨﺘﺳا ﺮﻈﺤﯾ تﻼﺑﺎﻜﻻا
ﻞﺒﻗ ﻦﻣ ةﺪﻤﺘﻌﻣ
Supermicro ةﺰﮭﺟأ ىﺮﺧأ ﺔﯿﺋﺎﺑﺮﮭﻛ ﺮﯿﻏ تﺎﺠﺘﻨﻤﻻا ﺔﻨﯿﻌﻤﻻا ﻞﺒﻗ ﻦﻣ يﻷ
(UL/CSA ﻞﻤﺤﺗ ﻲﺘﻻاﺔﻣﻼﻋ )
경고!
제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를
사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이
될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety
Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을
위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을
금지합니다.
4-20
FatTwin F648G2-FT+/FTPT+ User's Manual
Waarschuwing
Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,
stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecertifi ceerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.
Chapter 5: Advanced Serverboard Setup
5-5
5. Use your thumb and index nger to hold the CPU on its edges. Align the CPU
keys, which are semi-circle cutouts, against the socket keys.
Socket Keys
CPU Keys
6. Once they are aligned, carefully lower the CPU straight down into the socket.
(Do not drop the CPU on the socket. Do not move the CPU horizontally or
vertically. Do not rub the CPU against the surface or against any pins of the
socket to avoid damaging the CPU or the socket.)
Caution: You can only install the CPU inside the socket in one direction. Make sure
that it is properly inserted into the CPU socket before closing the load plate. If it doesn't
close properly, do not force it as it may damage your CPU. Instead, open the load
plate again and double-check that the CPU is aligned properly.
Chapter 5: Advanced Serverboard Setup
5-7
Installing a Passive CPU Heatsink
1. Apply the proper amount of thermal grease to the heatsink.
2. Place the heatsink on top of the CPU so that the two mounting holes on the
heatsink are aligned with those on the retention mechanism.
3. Insert two push-pins on the sides of the heatsink through the mounting holes
on the serverboard, and turn the push-pins clockwise to lock them.
Note: For optimized air ow, please follow your chassis air ow direction to
properly install the correct heatsink. Graphics included in this manual are
for reference only. They might look different from the components installed
in your system.
OPEN 1st
O
O
O
OPEN 1st
PEN 1st
PEN 1st
PEN 1st
Screw#1
Screw#2
Direction of Air ow
5-8
FatTwin F648G2-FT+/FTPT+ User's Manual
Removing the Passive Heatsink
Warning: We do not recommend that the CPU or the heatsink be removed. However,
if you do need to remove the heatsink, please follow the instructions below to uninstall
the heatsink to avoid damaging the CPU or other components.
1. Unplug the power cord from the power supply.
2. Press down the push-pin on the heatsink, and turn counter-clock-wise to
loosen it. Repeat the same step to loosen the second push-pin.
3. Hold the heatsink as shown in the picture below, and gently wriggle the
heatsink to loosen it. (Do not use excessive force when wriggling the
heatsink.)
4. Once the heatsink is loosened, remove it from the CPU.
Note: For optimized air ow, please follow your chassis air ow direction
to properly install the heatsink. Graphics included in this manual are for
reference only. They might look different from the components installed
in your system.
Loosen screws in
the sequence as
shown.
Screw#2
Serverboard
Screw#1
Screw#3
Screw#4
Direction of Air ow
Chapter 5: Advanced Serverboard Setup
5-9
5-5 Installing Memory
Caution: exercise extreme care when installing or removing DIMM modules to prevent
any possible damage.
Installing Memory
1. Insert the desired number of DIMMs into the memory slots, starting with
P1-DIMM #A1. (For best performance, please use the memory modules of the
same type and speed in the same bank.)
2. Push the release tabs outwards on both ends of the DIMM slot to unlock it.
3. Align the key of the DIMM module with the receptive point on the memory
slot.
4. Align the notches on both ends of the module against the receptive points on
the ends of the slot.
5. Use two thumbs together to press on both ends of the module straight down
into the slot until the module snaps into place.
6. Press the release tabs to the locking positions to secure the DIMM module
into the slot.
Reverse the steps above to remove the DIMM modules from the serverboard.
Note: 1 GB, 2 GB, 4 GB, 8 GB, 16 GB, 32 GB, 64 GB and 128 GB (3DS LRDIMM
only) size memory modules are supported. It is highly recommended that you
remove the power cord from the system before installing or changing memory
modules. Please refer to our web site for memory that has been tested on the
X10DRFF-iG/iTG serverboard.
Figure 5-2. Installing DIMM into Slot
Release Tabs
Notches
Press both notches straight down into
the memory slot at the same time.
Removing Memory Modules
Press the release tabs on both ends of the memory module to unlock it. Once it is
loosened, remove the DIMM module from the memory slot.
Chapter 5: Advanced Serverboard Setup
5-11
Populating Memory Modules
Populating RDIMM/LRDIMM DDR4 Memory Modules
Type
Ranks
Per
DIMM
and
Data
Width
DIMM Capacity
(GB)
Speed (MT/s); Voltage (V); Slots per Channel
(SPC) and DIMMs per Channel (DPC)
2 Slots per Channel
1 DPC 2 DPC
E5-2600
V3
E5-2600
V4
E5-2600
V3
E5-2600
V4
4 Gb 8 Gb 1.2 V 1.2 V 1.2 V 1.2 V
RDIMM SRx4 8 GB 16 GB 2133 2400 1866 2133
RDIMM SRx8 4 GB 8 GB 2133 2400 1866 2133
RDIMM DRx8 8 GB 16 GB 2133 2400 1866 2133
RDIMM DRx4 16 GB 32 GB 2133 2400 1866 2133
LRDIMM QRx4 32 GB 64 GB 2133 2400 2133 2400
LRDIMM 3DS 8Rx4 64 GB 128 GB 2133 2400 2133 2400
Other Important Notes and Restrictions
• For the memory modules to work properly, please install DIMM modules in pairs
(w/even number of DIMMs installed).
• Mixing memory modules of different types, different speeds or different sizes
is not allowed.
Chapter 5: Advanced Serverboard Setup
5-13
Notes:
1. For the latest CPU/Memory updates, please refer to our website at http://
www.supermicro.com/products/serverboard/ for details.
2. Use only the correct type of onboard CMOS battery as speci ed by the
manufacturer. Do not install the onboard battery upside down, in order to
avoid possible explosion.
3. Components/Jumpers/LED Indicators that are not documented in this manual
are reserved for internal testing only.
X10DRFF-iG/iTG Serverboard Jumpers
Jumper Description Default Setting
JBT1 Clear CMOS/Reset BIOS Con guration See Section 5-8 for details
JPB1 BMC Enabled Pins 1-2 (Enabled)
JPG1 VGA Enabled Pins 1-2 (Enabled)
JPL1 GLAN1/GLAN2 Enable (X10DRFF-iG) or 10G TLAN1/TLAN2
Enable (F648G2-FTPT+)
Pins 1-2 (Enabled)
JPME2 Manufacture Mode (ME) Select Pins 1-2 (Normal)
JWD1 Watch Dog Pins 1-2 (Reset)
X10DRFF-iG/iTG Serverboard LED Indicators
LED Description State
HDD_LED1 HDD Activity LED Green: Blinking (HDD Active)
Failure_LED2 Serverboard Failure LED
Solid: On (Overheating)
Blinking at 1Hz (Fan Failure)
Blinking at 0.25Hz (Power Supply Failure)
LEDBMC BMC Heartbeat LED Green: Blinking (BMC Normal)
UID_LED1 Rear UID LED Blue: On (Unit Identi ed)
Chapter 5: Advanced Serverboard Setup
5-15
5-7 Connector De nitions
Power Connectors
Two 8-pin power connectors (JPW1/
JPW2) provide main power to the
serverboard, while other two 8-pin power
connectors (HDD_PWR1/HDD_PWR2)
are used to supply power to HDD
devices. The 4-pin power connector
(JPW3) is used as auxiliary power. These
power connectors to provide adequate
power to the system. See the tables on
the right for pin de nitions.
12V 8-pin
Power Connector
(JPW1/JPW2)
Pin De nitions
Pins De nition
1 through 4 Ground
5 through 8 +12V
12V 8-pin
HDD PWR Connector
(HDD_PWR1/2HDD)
Pin De nitions
Pins De nition
1 +12V
2-3 Ground
4 +5V
Universal Serial Bus (USB)
Two USB ports (USB 12/13) are located
on the I/O panel to provide USB 3.0
connections to the system. (Cables are
not included.) See the tables on the right
and below for pin de nitions.
Panel USB 12/13 (3.0)
Pin De nitions
Pin# Description
1 VBUS
2 SSRX-
3 SSRX+
4 Ground
5 SSTX-
6 SSTX+
7 GND_DRAIN
8 D-
9 D+
Power Switch
A power switch is located next to the VGA port on the IO panel. Press this switch
to turn on or turn off the system power. See the layout below for the location of
the power switch.
Warning: To ensure adequate power supply to your serverboard, be sure to connect
all the power connectors mentioned above to your power supply For proper system
operation.

Product specificaties

Merk: Supermicro
Categorie: Server
Model: SuperServer F648G2-FTPT+

Heb je hulp nodig?

Als je hulp nodig hebt met Supermicro SuperServer F648G2-FTPT+ stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Server Supermicro

Supermicro

Supermicro SuperServer 6019U-TR4 Handleiding

30 Januari 2025
Supermicro

Supermicro SuperServer 2028TR-HTFR Handleiding

8 Januari 2025
Supermicro

Supermicro SuperServer AS-1015A-MT Handleiding

17 November 2024
Supermicro

Supermicro SuperServer SSG-640SP-DE2CR60 Handleiding

17 November 2024
Supermicro

Supermicro SuperServer 1018D-FRN8T Handleiding

17 November 2024
Supermicro

Supermicro SuperChassis 747TQ-R1400B Handleiding

17 November 2024
Supermicro

Supermicro A2SDV-4C-LN10PF Handleiding

17 November 2024
Supermicro

Supermicro SuperServer 5018A-MHN4 Handleiding

17 November 2024
Supermicro

Supermicro SuperServer 5018A-MLTN4 Handleiding

17 November 2024
Supermicro

Supermicro MicroBlade MBI-6119G-T7LX Handleiding

17 November 2024

Handleiding Server

Nieuwste handleidingen voor Server

MSI

MSI S1206-01 Handleiding

10 Maart 2025
MSI

MSI S2205-01 Handleiding

10 Maart 2025
MSI

MSI S2206-04 Handleiding

10 Maart 2025
MSI

MSI S1201 Handleiding

10 Maart 2025
MSI

MSI S2205-04 Handleiding

10 Maart 2025
MSI

MSI S2201 Handleiding

10 Maart 2025
MSI

MSI S2206-06-10G Handleiding

10 Maart 2025
MSI

MSI S1102-01 Handleiding

10 Maart 2025
MSI

MSI S2205-04-10G Handleiding

10 Maart 2025
MSI

MSI G4101 Handleiding

20 Februari 2025