Supermicro SuperServer 2028R-C1R Handleiding

Supermicro Server SuperServer 2028R-C1R

Lees hieronder de 📖 handleiding in het Nederlandse voor Supermicro SuperServer 2028R-C1R (146 pagina's) in de categorie Server. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/146

S Super erver®

2028r-C1rT

2028r-C1r

uSer’S MANuAL

Revision 1.0b

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software and

documentation, is the property of Supermicro and/or its licensors, and is supplied only under a

license. Any use or reproduction of this product is not allowed, except as expressly permitted by

the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class

A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instruction manual, may cause harmful

interference with radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference, in which case you will be required to correct the interference at your

own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Manual Revision 1.0b

Release Date: December 22, 2017

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

iii

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the SuperServers 2028R-C1RT

and 2028R-C1R. Installation and maintainance should be performed by experienced

technicians only.

SuperServer 2028R-C1R(T) User's Manual

Contents

Chapter 1 Introduction ..............................................................................1-1

1-1 Overview ......................................................................................................... 1-1

1-2 Serverboard Features ..................................................................................... 1-1

Processor 1-2 ........................................................................................................

Memory 1-2 ...........................................................................................................

SAS 1-2 ................................................................................................................

SATA .............................................................................................................. 1-2

PCI Expansion Slots ....................................................................................... 1-2

Rear I/O Ports ................................................................................................. 1-3

Other Features ................................................................................................ 1-4

1-3 Chassis Features ............................................................................................ 1-4

Drives 1-4 ..............................................................................................................

System Power ................................................................................................. 1-4

Front Control Panel ......................................................................................... 1-4

Cooling System ............................................................................................... 1-4

Mounting Rails ................................................................................................ 1-4

1-4 Contacting Supermicro .................................................................................... 1-5

1-5 Returning Merchandise for Service................................................................. 1-6

Chapter 2 Server Installation ...................................................................2-1

2-1 Unpacking the System .................................................................................... 2-1

2-2 Preparing for Setup ......................................................................................... 2-1

Choosing a Setup Location ............................................................................. 2-1

2-3 Warnings and Precautions .............................................................................. 2-2

Rack Precautions ............................................................................................ 2-2

Server Precautions .......................................................................................... 2-2

Rack Mounting Considerations ....................................................................... 2-3

Ambient Operating Temperature ................................................................ 2-3

Reduced Airow ......................................................................................... 2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading ..................................................................................... 2-3

Reliable Ground ......................................................................................... 2-3

2-4 Checking the Setup ......................................................................................... 2-4

Completing the Conguration ......................................................................... 2-5

2-5 Installing the System into a Rack ................................................................... 2-6

Identifying the Sections of the Rack Rails ...................................................... 2-6

Releasing the Inner Rail ................................................................................. 2-7

Preface

Installing the Inner Rails on the Chassis ........................................................ 2-8

Installing the Outer Rails onto the Rack ......................................................... 2-9

Sliding the Chassis onto the Rack Rails ....................................................... 2-10

Chapter 3 System Interface ......................................................................3-1

3-1 Overview ......................................................................................................... 3-1

3-2 Control Panel Buttons ..................................................................................... 3-2

3-3 Control Panel LEDs ........................................................................................ 3-2

Overheating 3-3 .....................................................................................................

Overheat Temperature Setting ................................................................... 3-3

Responses 3-3 ..................................................................................................

3-4 Drive Carrier LEDs .......................................................................................... 3-4

3-5 Power Supply LEDs ........................................................................................ 3-4

Chapter 4 Standardized Warning Statements for AC Systems ............4-1

About Standardized Warning Statements ....................................................... 4-1

Warning Denition ........................................................................................... 4-1

Installation Instructions .................................................................................... 4-4

Circuit Breaker ................................................................................................ 4-5

Power Disconnection Warning ........................................................................ 4-6

Equipment Installation ..................................................................................... 4-8

Restricted Area ................................................................................................ 4-9

Battery Handling ............................................................................................ 4-10

Redundant Power Supplies .......................................................................... 4-12

Backplane Voltage ........................................................................................ 4-13

Comply with Local and National Electrical Codes ........................................ 4-14

Product Disposal ........................................................................................... 4-15

Hot Swap Fan Warning ................................................................................. 4-16

Power Cable and AC Adapter ...................................................................... 4-18

Chapter 5 Advanced Serverboard Setup ................................................5-1

5-1 Handling the Serverboard ............................................................................... 5-1

Precautions 5-1 .....................................................................................................

Unpacking 5-1 .......................................................................................................

5-2 Installing the Processor and Heatsink ............................................................ 5-2

Installing an LGA 2011 Processor ................................................................... 5-2

Installing a CPU Heatsink ............................................................................... 5-5

Removing the Heatsink .................................................................................. 5-5

5-3 Connecting Cables .......................................................................................... 5-6

Connecting Data Cables ................................................................................. 5-6

Connecting Power Cables .............................................................................. 5-6

Connecting the Control Panel ......................................................................... 5-6

SuperServer 2028R-C1R(T) User's Manual

5-4 I/O Ports .......................................................................................................... 5-7

LAN Ports ........................................................................................................ 5-7

5-5 Installing Memory ............................................................................................ 5-8

Memory Support .............................................................................................. 5-9

Processor & Memory Module Population Conguration ............................ 5-9

5-6 Serverboard Details .......................................................................................5-11

Serverboard Quick Reference....................................................................... 5-12

5-7 Connector Denitions .................................................................................... 5-14

Front Control Panel ....................................................................................... 5-15

Input/Output Connectors ............................................................................... 5-17

Other Connectors .......................................................................................... 5-18

5-8 Jumper Settings ............................................................................................ 5-21

5-9 Onboard Indicators ........................................................................................ 5-23

5-10 SATA/SAS Connections ................................................................................ 5-25

5-11 Installing Software ......................................................................................... 5-26

SuperDoctor® 5 ............................................................................................. 5-27

5-12 Onboard Battery ............................................................................................ 5-29

Chapter 6 Advanced Chassis Setup ........................................................6-1

6-1 Static-Sensitive Devices .................................................................................. 6-2

Precautions 6-2 .....................................................................................................

Unpacking 6-2 .......................................................................................................

6-2 Hard Disk Drives ............................................................................................ 6-2

6-3 Peripheral Drive Installation ............................................................................ 6-5

6-4 Installing Expansion Cards ............................................................................ 6-6

6-5 Installing the Air Shroud .................................................................................. 6-7

Checking the Air Flow ..................................................................................... 6-7

6-6 System Fans ................................................................................................... 6-8

6-7 Installing the Serverboard ............................................................................. 6-10

I/O Shield ...................................................................................................... 6-10

Installing the I/O Shield ................................................................................. 6-10

Permanent and Optional Standoffs ................................................................6-11

6-8 Power Supply ................................................................................................ 6-12

Chapter 7 BIOS .........................................................................................7-1

7-1 Introduction ...................................................................................................... 7-1

Starting BIOS Setup Utility .............................................................................. 7-1

How To Change the Conguration Data ......................................................... 7-1

How to Start the Setup Utility ......................................................................... 7-2

7-2 Main Setup ...................................................................................................... 7-2

vii

Preface

7-3 Advanced Setup Congurations...................................................................... 7-4

7-4 Event Logs .................................................................................................... 7-39

7-5 IPMI ............................................................................................................... 7-41

7-6 Security Settings ........................................................................................... 7-43

7-7 Boot Settings ................................................................................................. 7-44

7-8 Save & Exit ................................................................................................... 7-46

Appendix A BIOS Error Beep Codes ..................................................... A-1

Appendix B System Specications ........................................................ B-1

viii

SuperServer 2028R-C1R(T) User's Manual

Notes

Chapter 1

Introduction

1-1 Overview

The 2028R-C1R(T) is a high-end server comprised of two main subsystems: the

SC213AC-R920LPB 2U server chassis and the X10DRH-C or X10DRH-CT dual

processor serverboard. The 2028R-C1R features four Gigabit LAN ports, and the

2028R-C1RT has four 10GBaseT LAN ports. Refer to the Supermicro web site for

information on operating systems that have been certied for use with the system

(www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have

been included with the 2028R-C1R(T), as listed below:

• Backplane (BPN-SAS3-213A)

• Cooling: three fans (FAN-0126L4), one air shroud (MCP-310-29001-0N), two

heat sinks (SNK-P0048PS)

• Mounting rails (MCP-290-00053-0N)

Note: For your system to work properly, please follow the links below to download

all necessary drivers/utilities and the user’s manual for your server.

• Product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety information:

http://www.supermicro.com/about/policies/safety_information.cfm

For support, email support@supermicro.com.

1-2 Serverboard Features

The SuperServer 2028R-C1R(T) is built around the X10DRH-C(T), a dual processor

serverboard based upon the Intel C612 Express chipset. Below are the main

features. Curent details are available on the Supermicro web site.

Chapter 1: Introduction

1-1

1-2

SuperServer 2028R-C1R(T) User's Manual

Processor

Each serverboard supports single or dual Intel Xeon E5-2600 v3/v4 processors in

Socket R3-LGA 2011. A complete listing of supported processors is available on

the Supermicro web site.

Memory

Each serverboard has 16 DIMM slots that can support up to 2 TB of Load

Reduced (LRDIMM) ECC registered memory or up to 512 GB of registered

(RDIMM) ECC modules. Memory type is 2400/2133/1866/1600 MHz DDR4. 72-

bit. DIMM sizes supported are RDIMM: 32 GB, 16 GB, 8 GB, 4 GB; LRDIMM: 64

GB, 32 GB. Refer to Section 5-6 before installing memory and the Supermicro

web site for recommended DIMMs.

SAS

An LSI 3108 SAS controller is included on the serverboard to support up to eight

SAS 3.0 ports with RAID 0, 1, 5, 6, 10, 50 and 60.

The SAS drives are hot-swappable if you set up RAID. Refer to RAID guidelines

on the Supermicro website.

SATA

A SATA controller is integrated into the C612 chipset to provide ten SATA 3.0 ports,

with RAID 0, 1, 5 and 10.

The SATA drives are hot-swappable if you set up RAID. Refer to RAID guidelines

on the Supermicro website.

PCI Expansion Slots

The serverboard has a total of seven PCI-E 3.0 slots: six x8 slots and one x16

slot. Note that both CPUs must be installed to make use of all the PCI slots. CPU1

controls Slot1-Slot3; CPU2 controls Slot4-Slot7.

Input/Output Ports

The I/O ports include two COM ports (one front, one rear), a VGA port, two USB 3.0

ports (rear), two USB 2.0 ports (rear), two more USB 2.0 ports (front), two Ethernet

LAN ports and a dedicated IPMI LAN port

• X10DRH-C has two Gigabit LAN ports

• X10DRH-CT has two 10GBaseT LAN ports

1-3

Chapter 1: Introduction

Figure 1-1. Intel C612 Express Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly represent

the features on your motherboard. See the previous pages for the

actual specications of your motherboard.

SPI

L 3 AN

RGRMII

Debug Card

FRONT PANEL

SYSTEM POWER

CTRL

FAN SPEED

PCI-E X1 G2

USB 2.0

PCH 612

6.0 Gb/S

USB 2.0

LPC

R E-VB-CGTL8211

R 5J4

BIOS

SPI

Temp Sensor

EMC1402-1 *2 at diff SMBUS

TPM HE ERAD

USB 3.0

BIOS

HE ERAD

SPI

AST 0240

BMC

RMII/NCSI

COM1

C toronnec

COM2

H derea

VGA CONN

BMC B t Fl hoo as

DDR3

5 PHASE

145W

VR12.5

QPI

9.6G

2 x PCI-E X8 G3 (LAN REVERSE)

2IMD2IMD

CPU1 CPU2

QPI

9.6G

5 PHASE

145W

VR12.5

X /I 0540 35

LAN1,2

PCI-E X8 G2

SLOT 4

SLOT 5

PCI-E X16

PCI-E X8

SLOT 6

PCI-E X8

PCI-E X8 G3

2 x PCI-E X8 G3

PCI-E X16 G3

#1 #2 #3#1 #3

#1-8 #2-8

#8#9

VCCP1 12v

PVCCIO

(1.05/0.95)

from 3.3v

PCI-E X8

SLOT 7

LSI

3108

PCI-E X8 G3

PCI-E X8

SLOT 1

PCI-E X8

SLOT 2

PCI-E X8

SLOT 3

PCI-E X8 G3 (LAN REVERSE)

USB 0/1, 2/3

USB 4/5, 6, 7/8

I-SATA 0,1,2,3

S-SATA 7,8,9,10

SATADOM 5,6

#1-7

#1-6

#1-5

#1-4

#1-3

#1-2

1333/2133

DDR4

#1-1

#2-7

#2-6

#2-5

#2-4

#2-3

#2-2

1333/2133

#2-1

DDR4

SATAUSB2USB3

Other Features

Other onboard features that promote system health include voltage monitors, a

chassis intrusion header, Watch Dog, auto-switching voltage regulators, chassis

and CPU overheat sensors and hardware BIOS virus protection.

1-4

SuperServer 2028R-C1R(T) User's Manual

1-3 Chassis Features

The following is a general outline of the main features of the SC213AC-R920LPB

server chassis.

Drives

The SC213 chassis includes sixteen 2.5" hard drive bays. It can accomodate

eight SAS3 12Gbps drives and eight SATA3 6Gbps drives. The drives can be hot-

swappable if supported by the operating system and RAID. Hard drives must be

purchased separately. The drives are enabled through a backplane.

A DVD drive is optional.

System Power

The system includes two redundant hot-plug, high-efciency power supplies, each

rated at 920 Watts.

Front Control Panel

The control panel on the front of the chassis displays LEDs to indicate system

power, HDD activity, network activity, system overheat and power supply failure. A

main power button and a system reset button are also included.

Cooling System

The system supports three fans powered from the motherboard. These fans are 2U

high and are powered by 4-pin connectors. It also includes heats sinks for each CPU

and a mylar air shroud that directs the airow where cooling is needed.

Mounting Rails

The system includes a set of quick-release rails for mounting in a rack.

1-5

Chapter 1: Introduction

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: marketing@supermicro.com (General Information)

support@supermicro.com (Technical Support)

Website: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: sales@supermicro.nl (General Information)

support@supermicro.nl (Technical Support)

rma@supermicro.nl (Customer Support)

Website: www.supermicro.nl

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3992

Email: support@supermicro.com.tw

Website: www.supermicro.com.tw

1-6

SuperServer 2028R-C1R(T) User's Manual

1-5 Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required before

any warranty service will be rendered. You can obtain service by calling your vendor

for a Returned Merchandise Authorization (RMA) number. When returning to the

manufacturer, the RMA number should be prominently displayed on the outside of

the shipping carton, and mailed prepaid or hand-carried. Shipping and handling

charges will be applied for all orders that must be mailed when service is complete.

For faster service, RMA authorizations may be requested online (http://www.

supermicro.com/support/rma/).

Whenever possible, repack the chassis in the original Supermicro carton, using the

original packaging material. If these are no longer available, be sure to pack the

chassis securely, using packaging material to surround the chassis so that it does

not shift within the carton and become damaged during shipping.

This warranty only covers normal consumer use and does not cover damages

incurred in shipping or from failure due to the alteration, misuse, abuse or improper

maintenance of products.

During the warranty period, contact your distributor rst for any product problems.

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

This chapter outlines the procedure to install your system into a rack. If your system

is not already fully integrated with a drives, processors, or system memory refer to

the relevant chapter for details on installing components.

2-1 Unpacking the System

You should inspect the box in which your server was shipped and note if it was

damaged. If the server itself shows damage, le a claim with the carrier.

2-2 Preparing for Setup

Decide on a suitable location for the rack unit that will hold the server. It should be

in a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical

noise and electromagnetic elds are generated. It must be near a grounded power

outlet.

The box in which the server was shipped includes two sets of rail assemblies, two

rail mounting brackets and mounting screws to install the system into the rack. The

installation procedure is provided later in this chapter. Please read this section and

"Warnings and Precautions" section before beginning the installation procedure.

Choosing a Setup Location

• Leave enough clearance in front of the rack to enable you to open the front

door completely (~25 inches) and approximately 30 inches of clearance in the

back of the rack to allow for sufcient airow and ease in servicing.

• This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets and the like).

• This product is not suitable for use with visual display work place devices

acccording to §2 of the the German Ordinance for Work with Visual Display

Units.

2-2

SuperServer 2028R-C1R(T) User's Manual

2-3 Warnings and Precautions

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to

the oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack. In mul-

tiple rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time. Extending two or more

simultaneously may cause the rack to become unstable.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack you install the before

rails.

• Install the heaviest server components on the bottom of the rack rst, and

then work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a

power failure.

• Allow any hot plug drives and power supply modules to cool before touching

them.

• Always keep the rack front door and all panels and components on the serv-

ers closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera-

ture of the rack environment may be greater than the ambient temperature of the

room. Therefore, consideration should be given to installing the equipment in an

environment compatible with the manufacturer’s maximum rated ambient tempera-

ture (Tmra).

Reduced Airow

Equipment should be mounted into a rack so that the amount of airow required

for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not

arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power

supply circuitry and the effect that any possible overloading of circuits might have

on overcurrent protection and power supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself

should be grounded. Particular attention should be given to power supply connec-

tions other than the direct connections to the branch circuit (i.e. the use of power

strips, etc.).

Warning! To prevent bodily injury when mounting or servicing this unit in a

rack, you must take special precautions to ensure that the system remains

stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in

the rack.

• When mounting this unit in a partially lled rack, load the rack from the bot-

tom to the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before

mounting or servicing the unit in the rack.

• Slide rail mounted equipment is not to be used as a shelf or a work space.

2-4

SuperServer 2028R-C1R(T) User's Manual

Figure 2-1. Removing the Chassis Cover

2-4 Checking the Setup

Open the unit to make sure the motherboard is properly installed and all the con-

nections have been made.

Removing the Chassis Cover

1. Remove the two screws on each side of the cover, which secure the cover to

the chassis.

2. Press the release tabs to remove the cover from the locked position. Press both

tabs at the same time.

3. Once the top cover is released from the locked position, slide the cover toward

the rear of the chassis and up.

4. Before operating the server for the rst time, it is important to remove the

protective lm covering the top of the chassis, to allow for proper ventilation

and cooling.

Remove

Screw

Remove

Screw

Caution: Except for short periods of time, do not operate the server without the

cover in place. The chassis cover must be in place to allow proper airow and

prevent overheating.Lift the cover off the chassis.

Chapter 2: Server Installation

2-5

Completing the Conguration

Your server may or may not come with hard disk drives, processors or system

memory already installed. The following sections refer you to the procedures for

installing these components.

Checking the Components and Setup

• To install processors and heatsinks into the motherboard, see Chapter 5 for

the procedure.

• To install system memory DIMMs, refer to Chapter 5.

• To install hard disk drives or optional peripheral drives, see the procedures in

Chapter 6.

• To install expansion cards to the system, see Chapter 6.

Checking the Airow

• Airow is provided by three 8-cm chassis cooling fans. The system compo-

nent layout was carefully designed to direct sufcient cooling airow to the

components that generate the most heat.

• To install the air shroud that assists with air ow, see Chapter 6.

• Make sure all power and data cables are properly connected and not blocking

the chassis airow. Also make sure that no cables are positioned in front of

the fans.

Providing Power

After installing or checking components and mounting your server in its rack, con-

nect the power.

1. Plug the power cords from the power supply units into a high-quality power strip

that offers protection from electrical noise and power surges. It is recommended

that you use an uninterruptible power supply (UPS).

2. Depress the power button on the front of the chassis.

2-6

SuperServer 2028R-C1R(T) User's Manual

2-5 Installing the System into a Rack

This section provides information on installing the chassis into a rack unit with the

rails provided. There are a variety of rack units on the market, which may mean

that the assembly procedure will differ slightly from the instructions provided. You

should also refer to the installation instructions that came with the rack unit you are

using. Note: This rail will t a rack between 26.8" and 36.4" deep.

Identifying the Sections of the Rack Rails

The chassis package includes two rail assemblies. Each assembly consists of three

sections: An inner rail that secures directly to the chassis, an outer rail that secures

to the rack, and a middle rail which extends from the outer rail. These assemblies

are specically designed for the left and right side of the chassis.

Figure 2-1. Identifying the Outer Rail, Middle Rai Rail

(Left Rail Assembly Shown)

Inner Rail

Rail Assembly

(Shown with Rails

Retracted)

This Side Faces

Outward

Locking Tab

Middle Rail

Outer Rail

Chapter 2: Server Installation

2-7

Figure 2-2. Extending and Releasing the Inner Rail

Releasing the Inner Rail

Each inner rail has a locking latch. This latch prevents the server from coming

completely out of the rack when when the chassis is pulled out for servicing.

To mount the rail onto the chassis, rst release the inner rail from the outer rails.

Releasing Inner Rail from the Outer Rails

1. Pull the inner rail out of the outer rail until it is fully extended as illustrated below.

2. Press the locking tab down to release the inner rail.

3. Pull the inner rail all the way out.

4. Repeat for the other outer rail.

2-8

SuperServer 2028R-C1R(T) User's Manual

Installing the Inner Rails on the Chassis

Installing the Inner Rails

1. Identify the left and right inner rails. They are labeled.

2. Place the inner rail rmly against the side of the chassis, aligning the hooks on

the side of the chassis with the holes in the inner rail.

3. Slide the inner rail forward toward the front of the chassis until the quick release

bracket snaps into place, securing the rail to the chassis.

4. Optionally, you can further secure the inner rail to the chassis with a screw.

5. Repeat for the other inner rail.

Figure 2-3. Installing the Inner Rails

Figure 6-4. Inner Rails Installed on the Chassis

Chapter 2: Server Installation

2-9

Figure 6-5. Extending and Mounting the Outer Rails

Installing the Outer Rails onto the Rack

Installing the Outer Rails

1. Press upward on the locking tab at the rear end of the middle rail.

2. Push the middle rail back into the outer rail.

3. Hang the hooks on the front of the outer rail onto the square holes on the front

of the rack. If desired, use screws to secure the outer rails to the rack.

4. Pull out the rear of the outer rail, adjusting the length until it just ts within the

posts of the rack.

5. Hang the hooks of the rear section of the outer rail onto the square holes on the

rear of the rack. Take care that the proper holes are used so the rails are level.

If desired, use screws to secure the rear of the outer rail to the rear of the rack.

6. Repeat for the other outer rail.

Stability hazard. The rack stabilizing mechanism must be in place, or the rack

must be bolted to the oor before you slide the unit out for servicing. Failure to

stabilize the rack can cause the rack to tip over.

Do not use a two post "telco" type rack.

2-10

SuperServer 2028R-C1R(T) User's Manual

Figure 6-6. Installing into a Rack

Ball-Bearing

Shuttle

Sliding the Chassis onto the Rack Rails

Warning: Mounting the system into the rack requires at least two people to

support the chassis during installation. Please follow safety recommendations

printed on the rails.

Installing the Chassis into a Rack

1. Extend the outer rails as illustrated above.

2. Align the inner rails of the chassis with the outer rails on the rack.

3. Slide the inner rails into the outer rails, keeping the pressure even on both

sides. When the chassis has been pushed completely into the rack, it should

click into the locked position.

4. Optional screws may be used to hold the front of the chassis to the rack.

Note: The gure above is for illustrative purposes only. Always install servers to

the bottom of the rack rst.

Caution: Do not pick up the server with the front handles. They are designed

to pull the system from a rack only.

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

The server includes:

• A control panel on the front that houses power buttons and status monitoring

lights

• Status lights on the externally accessible hard drives

• Status lights for the power supply visible from the back of the chassis

Figure 3-1. Control Panel

SUPERSERVER 2028R-C1R(T) User's Manual

3-2

3-3 Control Panel LEDs

There are six LEDs that provide status information about the system.

Power: The main power switch is used to apply or remove power from the power

supply to the server system. Turning off system power with this button removes the

main power but keeps standby power supplied to the system. Therefore, you must

unplug system before servicing.

Reset: The reset button is used to reboot the system.

3-2 Control Panel Buttons

The chassis includes two push-buttons that control power to the system.

Power: Indicates power is being supplied to the system power supply units. This

LED should normally be illuminated when the system is operating.

HDD: Indicates activity on the hard drive when ashing.

NIC2: Indicates network activity on GLAN2 when ashing.

Chapter 3: System Interface

3-3

NIC1: Indicates network activity on GLAN1 when ashing.

Information LED: Alerts operator of several states, as noted in the table below.

Information LED

Status Description

Continuously on and red An overheat condition has occured.

(This may be caused by cable congestion.)

Blinking red (1Hz) Fan failure, check for an inoperative fan.

Blinking red (0.25Hz) Power failure, check for a non-operational power supply.

Solid blue Local UID has been activated. Use this function to locate

the server in a rack mount environment.

Blinking blue Remote UID is on. Use this function to identify the

server from a remote location.

Overheating

There are several possible responses if the system overheats.

Overheat Temperature Setting

Some backplanes allow the overheat temperature to be set at 45, 50, or 55 by

changing a jumper setting. For more information, consult the backplane user manual

at www.supermicro.com. (Click Support, then the Manuals link.)

Responses

If the server overheats:

1. Use the LEDs to determine the nature of the overheating condition.

NIC1: Indicates network activity on GLAN1 when ashing.

SUPERSERVER 2028R-C1R(T) User's Manual

3-4

2. Conrm that the chassis covers are installed properly.

3. Check the routing of the cables and make sure all fans are present and operating

normally.

4. Verify that the heatsinks are installed properly.

3-4 Drive Carrier LEDs

The chassis includes externally accessible SAS/SATA drives. Each drive carrier

displays two status LEDs on the front of the carrier.

• Green: When illuminated, this LED indicates drive activity. It blinks on and off

when that particular drive is being accessed This function is controlled by the

backplane.

• Red: When illuminated, this LED indicates a drive failure. You should be notied

by your system management software.

3-5 Power Supply LEDs

On the rear of the power supply module, an LED displays the status.

• Solid Green: When illuminated, indicates that the power supply is on.

• Solid Amber: When illuminated, indicates the power supply is plugged in and

turned off, or the system is off but in an abnormal state.

• Blinking Amber: When blinking, this system power supply temperature has

reached 63C. The system will automatically power-down when the power supply

temperature reaches 70C and restarts when the power supply temperature

goes below 60C.

4-1

Chapter 4: Warning Statements for AC Systems

Chapter 4

Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user

of situations which have the potential for bodily injury. Should you have questions

or experience difficulty, contact Supermicro's Technical Support department

for assistance. Only certied technicians should attempt to install or congure

components.

Read this appendix in its entirety before installing or conguring components in the

Supermicro chassis.

These warnings may also be found on our web site at http://www.supermicro.com/

about/policies/safety_information.cfm.

Warning!

This warning symbol means danger. You are in a situation that could cause bodily

injury. Before you work on any equipment, be aware of the hazards involved with

electrical circuitry and be familiar with standard practices for preventing accidents.

Warning Denition

警告の定義

この警告サインは危険を意味します。

人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、

電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分意

识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结尾的

声明号码找到此设备的安全性警告说明的翻译文本。

此警告符號代表危險。

您目前所處的工作環境可能讓您受傷。您使用任何設備之前，請注意觸電的危險，

並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號碼找到相關

的翻譯說明內容。

4-2

SuperServer 2028R-C1R(T) User's Manual

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie benden sich in einer Situation, die zu

Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den

Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung

vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen

Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes

de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y

familiarícese con los procedimientos estándar de prevención de accidentes. Al

nal de cada advertencia encontrará el número que le ayudará a encontrar el texto

traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES.

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une

situation pouvant entraîner des blessures ou des dommages corporels. Avant

de travailler sur un équipement, soyez conscient des dangers liés aux circuits

électriques et familiarisez-vous avec les procédures couramment utilisées pour

éviter les accidents. Pour prendre connaissance des traductions des avertissements

gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,

référez-vous au numéro de l'instruction situé à la n de chaque avertissement.

CONSERVEZ CES INFORMATIONS.

הרהזא תורהצה ןונקת

הלבח ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהזא ןה תואבה

הכימת תקלחמ םע רשק רוציל שי ,יהשלכ היעבב תולקתיה וא תולאש שיו הדימב .תירשפ

.םיביכרה תא רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש

.ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא אור

4-3

Warning Statements for AC Systems

  

!

      .      

   .       

        

   .

          



BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,

dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's

en dient u op de hoogte te zijn van de standaard procedures om ongelukken te

voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te

herleiden naar de desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

.  !           



   

 

            



 

    



      

         

  



   

4-4

SuperServer 2028R-C1R(T) User's Manual

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power source.

Warnung

Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen

lesen.

¡Advertencia!

Lea las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Attention

Avant de brancher le système sur la source d'alimentation, consulter les directives

d'installation.

設置手順書

システムを電源に接続する前に、設置手順書をお読み下さい。

      .

Waarschuwing

Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron

aansluit.

警告

将此系统连接电源前,请先阅读安装说明。

警告

將系統與電源連接前，請先閱讀安裝說明。

.חתמ רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תא אורקל

        

4-5

Chapter 4: Warning Statements for AC Systems

Circuit Breaker

Warning!

This product relies on the building's installation for short-circuit (overcurrent)

protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.

サーキット・ブレーカー

この製品は、短絡（過電流）保護装置がある建物での設置を前提としています。

保護装置の定格が250 V、20 Aを超えないことを確認下さい。

Warnung

Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss-

bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der

Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.

¡Advertencia!

Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)

del edicio. Asegúrese de que el dispositivo de protección no sea superior a: 250

V, 20 A.

Attention

Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit

dépend de l'installation électrique du local. Vériez que le courant nominal du

dispositif de protection n'est pas supérieur à :250 V, 20 A.

警告

此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电

流不大于250V,20A。

警告

此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電

流不大於250V,20A。

יכ אדוול שי .ילמשח רצק תעינמל םינבמב תנקתומה הנגה לע ךמתסמ

250VDC, 20A-מ רתוי אל אוה ילמשחה רצקה ינפמ ןגמה רישכמ

4-6

SuperServer 2028R-C1R(T) User's Manual

Power Disconnection Warning

電源切断の警告

システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス

するには、

システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り

外す必要があります。

警告

在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。

警告

在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。

Warnung

Das System muss von allen Quellen der Energie und vom Netzanschlusskabel

getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es

auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder

zu entfernen.

Warning!

The system must be disconnected from all sources of power and the power cord

removed from the power supply module(s) before accessing the chassis interior to

install or remove system components.

!

   ()     

.    250V(), 20A() 

  .

Waarschuwing

Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van

uw electrische installatie. Controleer of het beveiligde aparaat niet groter

gedimensioneerd is dan 220V, 20A.

           



20A, 250V :         

4-7

Chapter 4: Warning Statements for AC Systems

¡Advertencia!

El sistema debe ser disconnected de todas las fuentes de energía y del cable

eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso

el interior del chasis para instalar o para quitar componentes de sistema.

Attention

Le système doit être débranché de toutes les sources de puissance ainsi que de

son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour

installer ou enlever des composants de systéme.

!

        

       

.

Waarschuwing

Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren

of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle

stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen

ילמשח קותינ ינפמ הרהזא

הרהזא!

קפסהמ ילמשחה לבכ תא ריסהל שיו למשחה תורוקמ לכמ תכרעמה תא

םיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השי

            

 

         

4-8

SuperServer 2028R-C1R(T) User's Manual

Equipment Installation

機器の設置

トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可

されています。

Warning!

Only trained and qualied personnel should be allowed to install, replace, or service

this equipment.

Warnung

Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,

qualiziertem Personal gestattet werden.

¡Advertencia!

Solamente el personal calicado debe instalar, reemplazar o utilizar este equipo.

Attention

Il est vivement recommandé de confier l'installation, le remplacement et la

maintenance de ces équipements à des personnels qualiés et expérimentés.

!

      ,     

.

警告

只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。

警告

只有經過受訓且具資格人員才可安裝、更換與維修此設備。

!הרהזא

.דויצה רובע תוריש תתל וא דויצה תא ףילחהל ,ןיקתהל יאשר דבלב ךמסומ

            

4-9

Chapter 4: Warning Statements for AC Systems

アクセス制限区域

このユニットは、アクセス制限区域に設置されることを想定しています。

アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いての

み出入りが可能です。

Warning!

This unit is intended for installation in restricted access areas. A restricted access

area can be accessed only through the use of a special tool, lock and key, or other

means of security. (This warning does not apply to workstations).

Restricted Area

Waarschuwing

Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door

geschoold en gekwaliceerd personeel.

Warnung

Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.

Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und

Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.

¡Advertencia!

Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.

Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una

herramienta especial, cerradura con llave u otro medio de seguridad.

Attention

Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une

zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme

de verrouillage et une clé, ou tout autre moyen de sécurité.

警告

此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和钥

匙或其它安全手段进出的场所。

警告

此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙或

其他安全方式才能進入的區域。

4-10

SuperServer 2028R-C1R(T) User's Manual

Battery Handling

Warning!

There is the danger of explosion if the battery is replaced incorrectly. Replace the

battery only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions

경고!

이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및

키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.

Waarschuwing

Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.

Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te

maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー

カーが推奨する型、または同等のものを使用下さい。使用済電池は製造元の指示に従

って処分して下さい。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更

换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有

電池。請按照製造商的說明指示處理廢棄舊電池。

תלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

(.דכו לוענמ ,חתפמ( דבלב החטבא ילכ'

. 





4-11

Chapter 4: Warning Statements for AC Systems

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.

Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Attention

Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.

Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!

Existe peligro de explosión si la batería se reemplaza de manera incorrecta.

Reemplazar la batería exclusivamente con el mismo tipo o el equivalente

recomendado por el fabricante. Desechar las baterías gastadas según las

instrucciones del fabricante.

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와

동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.

제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing

Er is ontplofngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen

wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd

te worden.

!הרהזא

ףילחהל שי .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ץוציפ תנכס תמייק

.תצלמומ ןרצי תרבחמ םאותה גוסב הללוסה תא

.ןרציה תוארוה יפל עצבל שי תושמושמה תוללוסה קוליס

           

 

          

       

4-12

SuperServer 2028R-C1R(T) User's Manual

Warnung

Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass

der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

¡Advertencia!

Puede que esta unidad tenga más de una conexión para fuentes de alimentación.

Para cortar por completo el suministro de energía, deben desconectarse todas las

conexiones.

Attention

Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute

tension et tout courant électrique de l'unité, toutes les connexions d'alimentation

doivent être débranchées.

Redundant Power Supplies

Warning!

This unit might have more than one power supply connection. All connections must

be removed to de-energize the unit.

冗長電源装置

このユニットは複数の電源装置が接続されている場合があります。

ユニットの電源を切るためには、すべての接続を取り外さなければなりません。

警告

此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。

警告

此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。

דחא קפסמ רתוי םייק םא

!הרהזא

ןקורל תנמ לע םירוביחה לכ תא ריסהל שי .קפס לש דחא רוביחמ רתוי שי הדחיל

.הדיחיה תא

4-13

Chapter 4: Warning Statements for AC Systems

Backplane Voltage

バックプレーンの電圧

システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。

修理する際には注意ください。

警告

当系统正在进行时，背板上有很危险的电压或能量，进行维修时务必小心。

警告

當系統正在進行時，背板上有危險的電壓或能量，進行維修時務必小心。

Warnung

Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche

Spannungen oder Energien auf. Vorsicht bei der Wartung.

¡Advertencia!

Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.

Tenga cuidado cuando lo revise.

Attention

Lorsque le système est en fonctionnement, des tensions électriques circulent sur

le fond de panier. Prendre des précautions lors de la maintenance.

Warning!

Hazardous voltage or energy is present on the backplane when the system is

operating. Use caution when servicing.

경고!

이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에

전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.

Waarschuwing

Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle

aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.

.         

       

4-16

SuperServer 2028R-C1R(T) User's Manual

Waarschuwing

De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

ファン・ホットスワップの警告

警告！回転部品に注意。運転中は回転部(羽根)に触れないでください。シャーシから冷

却ファン装置を取り外した際、ファンがまだ回転している可能性があります。ファンの開

口部に、指、ドライバー、およびその他のものを近づけないで下さい。

警告!

警告！危险的可移动性零件。请务必与转动的风扇叶片保持距离。当您从机架移除

风扇装置，风扇可能仍在转动。小心不要将手指、螺丝起子和其他物品太靠近风扇

警告

危險的可移動性零件。請務必與轉動的風扇葉片保持距離。當您從機架移除風扇裝

置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他物品太靠近風扇。

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Hot Swap Fan Warning

Warning!

Hazardous moving parts. Keep away from moving fan blades. The fans might still

be turning when you remove the fan assembly from the chassis. Keep ngers,

screwdrivers, and other objects away from the openings in the fan assembly's

housing.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

רצומה קוליס

!הרהזא

.הנידמה יקוחו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס

             

4-19

Chapter 4: Warning Statements for AC Systems

¡Advertencia!

Cuando instale el producto, utilice la conexión provista o designada o procure

cables, Cables de alimentación y adaptadores de CA que cumplan con los códigos

locales y los requisitos de seguridad, incluyendo el tamaño adecuado del cable y el

enchufe. El uso de otros cables y adaptadores podría causar un mal funcionamiento

o un incendio. La Ley de Seguridad de Aparatos Eléctricos y de Materiales prohíbe

El uso de cables certicados por UL o CSA (que tienen el certicado UL / CSA en

el código) para cualquier otros dispositivos eléctricos que los productos designados

únicamente por Supermicro.Attention

Attention

Lors de l'installation du produit, utilisez les cables de connection fournis ou désigné

ou achetez des cables, cables de puissance et adaptateurs respectant les normes

locales et les conditions de securite y compris les tailles de cables et les prises

electriques appropries. L'utilisation d'autres cables et adaptateurs peut provoquer

un dysfonctionnement ou un incendie. Appareils électroménagers et la Loi sur la

Sécurité Matériel interdit l'utilisation de câbles certies- UL ou CSA (qui ont UL ou

CSA indiqué sur le code) pour tous les autres appareils électriques sauf les produits

désignés par Supermicro seulement.

ימאתמו םיילמשח םילבכ AC

הרהזא!

םימאתמו םיקפס ,םילבכב שמתשהל שי ,רצומה תא םיניקתמ רשאכ וא ושכרנ רשא AC

הנוכנ הדימ ללוכ ,תוימוקמה תוחיטבה תושירדל ומאתוה רשאו ,הנקתהה ךרוצל ומאתוה

רצק וא הלקתל םורגל לולע ,רחא גוסמ םאתמ וא לבכ לכב שומיש . עקתהו לבכה לש

שמתשהל רוסיא םייק ,תוחיטבה יקוחו למשחה ירישכמב שומישה יקוחל םאתהב .ילמשח

ב םיכמסומה םילבכב ב וא לש דוק םהילע עיפומ רשאכ- UL -CSA ( (UL/CSA רובע

י"ע םאתוה רשא רצומב קר אלא ,רחא ילמשח רצומ לכ Supermicro דבלב.

               

  .             

       .        

              UL CSA  (UL/CSA)

   Supermicro.

4-20

SuperServer 2028R-C1R(T) User's Manual

전원 케이블 및 AC 어댑터

경고! 제품을 설치할 때 현지 코드 및 적절한 굵기의 코드와 플러그를 포함한 안전

요구 사항을 준수하여 제공되거나 지정된 연결 혹은 구매 케이블, 전원 케이블 및

AC 어댑터를 사용하십시오.

다른 케이블이나 어댑터를 사용하면 오작동이나 화재가 발생할 수 있습니다. 전기

용품 안전법은 UL 또는 CSA 인증 케이블 (코드에 UL / CSA가 표시된 케이블)

을 Supermicro가 지정한 제품 이외의 전기 장치에 사용하는 것을 금지합니다.

Stroomkabel en AC-Adapter

Waarschuwing! Bij het aansluiten van het Product uitsluitend gebruik maken van de

geleverde Kabels of een andere geschikte aan te schaffen Aansluitmethode, deze

moet altijd voldoen aan de lokale voorschriften en veiligheidsnormen, inclusief de

juiste kabeldikte en stekker. Het gebruik van niet geschikte Kabels en/of Adapters

kan een storing of brand veroorzaken. Wetgeving voor Elektrische apparatuur en

Materiaalveiligheid verbied het gebruik van UL of CSA -gecerticeerde Kabels (met

UL/CSA in de code) voor elke andere toepassing dan de door Supermicro hiervoor

beoogde Producten.

Chapter 5: Advanced Serverboard Setup

5-1

Chapter 5

Advanced Serverboard Setup

This chapter covers the steps required to install processors and heatsinks to the

X10DRH-C(T) serverboard, connect the data and power cables and install add-on

cards. All serverboard jumpers and connections are described and a layout and

quick reference chart are included in this chapter. Remember to close the chassis

completely when you have nished working on the serverboard to protect and cool

the system sufciently.

5-1 Handling the Serverboard

Static electrical discharge can damage electronic com ponents. To prevent damage

to printed circuit boards, it is important to handle them very carefully (see Chapter

4). Also note that the size and weight of the serverboard can cause it to bend if

handled improperly, which may result in damage. To prevent the serverboard from

bending, keep one hand under the center of the board to support it when handling.

The following measures are generally sufcient to protect your equipment from

static discharge.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing any board from its antistatic bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard, add-on cards and peripherals back into their antistatic

bags when not in use.

Unpacking

The serverboard is shipped in antistatic packaging to avoid static damage. When

unpacking the board, make sure the person handling it is static protected.

5-2

S SUPER ERVER 2028R-C1R(T) User's Manual

5-2 Installing the Processor and Heatsink

Notes:

• Always remove the power cord before adding, removing or changing a CPU.

• When receiving a serverboard without a processor pre-installed, make sure that

the plastic CPU socket cap is in place and none of the socket pins are bent;

otherwise, contact your retailer immediately.

• If you buy a CPU separately, use only an Intel-certied, multi-directional heatsink.

• Avoid placing direct pressure to the top of the processor package.

• Install the processor into the CPU socket before installing the heatsink.

• Refer to the Supermicro web site for updates on CPU support.

Installing an LGA 2011 Processor

Release

the lever labeled "Open 1st"

Installing a CPU

1. There are two levers on the LGA 2011

socket. First press and release the

load lever labeled "Open 1st".

OPEN 1st

Release

the lever labeled "Close 1st"

2. Press the second load lever labeled

"Close 1st" to release the load plate

from its locked position.

Chapter 5: Advanced Serverboard Setup

5-3

3. Wit h the s ec ond leve r full y

retracted, gently push down on

the "Open 1st" lever to loosen the

load plate. Lift the load plate with

your ngers to open it completely.

4. Pop the plas tic c ap mar ked

"Warning" out of the load plate.

5. Holding the CPU carefully above

the socket, orient the CPU so

that all keys and edges will t the

socket.

OPEN 1st

IMPORTANT!

Caution: You can only install the CPU into the socket in one direction. Make sure

that the CPU is properly inserted into the socket before closing the load plate. If it

does not close properly, do not force it as it may damage your CPU. Instead, open

the load plate again and double-check that the CPU is aligned properly.

Open the load

plate.

6. Carefully lower the CPU straight

down into the socket. Do not

move the CPU horizontally, and

do not rub the pins of the socket.

This may damage the CPU or the

socket.

5-4

S SUPER ERVER 2028R-C1R(T) User's Manual

8. Make sure the locking mechanism

on the "Close 1st" lever catches the

lip of the load plate. Close and lock

the "Close 1st" lever.

Push down and lock

the

lever labeled "Open 1st"

OPEN 1st

Push down and lock the lever

labeled "Close 1st".

9. Close and lock the "Open 1st" lever.

Engage the lip

of the load plate

and locking

portion of the

lever."

7. With the "Close 1st" lever fully

retracted, gently close the load

plate.

Gently close

the load plate.

5-6

S SUPER ERVER 2028R-C1R(T) User's Manual

5-3 Connecting Cables

Now that the processors are installed, the next step is to connect the cables to the

serverboard. These include the data (ribbon) cables for the peripherals and control

panel and the power cables.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully

routed in precongured systems to prevent them from blocking the ow of cooling

air that moves through the system from front to back. If you need to disconnect any

of these cables, you should take care to reroute them as they were originally after

reconnecting them and be aware of the pin 1 locations. If you are conguring the

system, keep the airow in mind when routing the cables.

Connecting Power Cables

The serverboard has a 24-pin primary power supply connector designated J24

for connection to the power supply. There are also two 8-pin power connectors,

JPWR1 and JPWR2. Connect the appropriate cable connectors from the power

supply. Connector pin denitions are explained later in the chapter.

Connecting the Control Panel

JF1 contains header pins for the front control panel connectors. All JF1 wires have

been bundled into single keyed ribbon cable to simplify their connection. The red

wire in the ribbon cable plugs into pin 1 of JF1. Connect the other end of the cable

to the Control Panel printed circuit board, located just behind the system status

LEDs in the chassis.

See the Connector Denitions section in this chapter for details and pin descriptions

of JF1.

Chapter 5: Advanced Serverboard Setup

5-7

5-4 I/O Ports

Figure 5-2 shows the I/O ports on the rear of the system.

Figure 5-2. Rear Panel I/O Ports

LAN Ports

The 2028R-C1R uses the X10DRH-C serverboard, and the LAN ports offer gigbit

speed. The 2028R-C1RT uses the X10DRH-CT, and the LAN ports provide

10GBase-T.

Rear I/O Ports

1. COM Port 1

2. USB Port 0 (USB 2.0)

3. USB Port 1 (USB 2.0)

4. Dedicated IPMI LAN

5. USB Port 4 (USB 3.0)

6. USB Port 5 (USB 3.0)

7. LAN Port 1

8. LAN Port 2

9 VGA Port

10 UID Button

1 987

5-8

S SUPER ERVER 2028R-C1R(T) User's Manual

5-5 Installing Memory

Note: Check the Supermicro web site for recommended memory modules.

CAUTION

Exercise extreme care when installing or removing DIMM modules

to prevent any possible damage.

Installing DIMMs

1. Insert the desired number of DIMMs into the memory slots, starting with slot

DIMMA1.

2. Push the release tabs outwards on both ends of the DIMM slot to unlock it.

3. Align the key on the DIMM module with the receptive point on the slot.

4. Use two thumbs together to press on both ends of the module straight down

into the slot until the module snaps into place.

5. Press the release tabs to the lock positions to secure the DIMM module into

the slot. See Figure 5-3.

Figure 5-3. Installing DIMM into Slot

Socket Key

Release Tab

Chapter 5: Advanced Serverboard Setup

5-9

Memory Support

The server features 16 DIMM slots that can support up to 2 TB of Load Reduced

(LRDIMM) ECC registered memory or up to 512 GB of registered (RDIMM) DDR4-

2400/2133/1866/1600 memory. For the latest memory updates, please refer to our

website at http://www.supermicro.com/products/motherboard.

Processor & Memory Module Population Conguration

For memory to work properly, follow the tables below for memory installation.

Processors and their Corresponding Memory Modules

CPU# Corresponding DIMM Modules

CPU 1 P1-

DIMMA1

P1-

DIMMB1

P1-

DIMMC1

P1-

DIMMD1

P1-

DIMMA2

P1-

DIMMB2

P1-

DIMMC2

P1-

DIMMD2

CPU2 P2-

DIMME1

P2-

DIMMF1

P2-

DIMMG1

P2-

DIMMH1

P2-

DIMME2

P2-

DIMM F2

P2-

DIMMG2

P2-

DIMMH2

Processor and Memory Module Population for Optimal Performance

Number of

CPUs+DIMMs

CPU and Memory Population Conguration Table

(For memory to work properly, please follow this table.)

1 CPU &

2 DIMMs

CPU1

P1-DIMMA1/P1-DIMMB1

1 CPU &

4 DIMMs

CPU1

P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

1 CPU &

5~8 DIMMs

CPU1

P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 + any pair of P1-DIMMA2/P1-

DIMMB2/P1-DIMMC2/P1-DIMMD2 slots

2 CPUs &

4 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

2 CPUs &

6 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1

2 CPUs &

8 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-

DIMMG1/P2-DIMMH1

2 CPUs &

9~16 DIMMs

CPU1/CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-

DIMMG1/P2-DIMMH1 + any pair of P1, P2 DIMM slots

2 CPUs &

16 DIMMs

CPU1/CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/

P2-DIMMG1/P2-DIMMH1,P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-

DIMME2/P2-DIMMF2/P2-DIMMG2/P2-DIMMH2

5-10

S SUPER ERVER 2028R-C1R(T) User's Manual

Caution: For the memory to work properly, install DIMMs of the same type and

speed. Mixing of DIMMs of different types or speeds is not allowed.

Populating DDR4 Memory Modules

Populating RDIMM/LRDIMM DDR4 Memory Modules

Type

Ranks

Per DIMM

and Data

Width

DIMM Capacity

(GB)

Speed (MT/s); Voltage (V); Slots per Channel (SPC) and

DIMMs per Channel (DPC)

2 Slots per Channel

1 DPC 2 DPC

E5-2600 V3 E5-2600 V4 E5-2600 V3 E5-2600 V4

4 GB 8 GB 1.2 V 1.2 V 1.2 V 1.2 V

RDIMM SRx4 8 GB 16 GB 2133 2400 1866 2133

RDIMM SRx8 4 GB 8 GB 2133 2400 1866 2133

RDIMM DRx8 8 GB 16 GB 2133 2400 1866 2133

RDIMM DRx4 16 GB 32 GB 2133 2400 1866 2133

LRDIMM QRx4 32 GB 64 GB 2133 2400 2133 2400

LRDIMM 3DS 8Rx4 64 GB 2133 2400 2133 2400128 GB

Product specificaties

Merk:	Supermicro
Categorie:	Server
Model:	SuperServer 2028R-C1R
Kleur van het product:	Zwart
Breedte:	437 mm
Diepte:	630 mm
Hoogte:	89 mm
LED-indicatoren:	Ja
Processorfamilie:	Intel
Ethernet LAN:	Ja
Aantal USB 2.0-poorten:	4
VGA (D-Sub)poort(en):	1
Aantal Ethernet LAN (RJ-45)-poorten:	3
Netvoeding:	920 W
Duurzaamheidscertificaten:	RoHS
Ethernet LAN, data-overdrachtsnelheden:	1000 Mbit/s
Temperatuur bij opslag:	-40 - 70 °C
Aantal ventilatoren:	3 ventilator(en)
Processor socket:	LGA 2011-v3
Systeembus:	9.6 GT/s
Maximum intern geheugen:	1000 GB
On-board graphics adapter model:	Aspeed AST2400
Luchtvochtigheid bij opslag:	5 - 95 procent
Type behuizing:	Rack (2U)
Overtollige fans ondersteuning:	Ja
ECC:	Ja
Ethernet interface type:	Gigabit Ethernet
PCI Express x1 slots:	16
Koperen ethernetbekabelingstechnologie:	1000BASE-T, 100BASE-TX
Ondersteunde opslagstationinterfaces:	Serial Attached SCSI (SAS)-3, Serial ATA III
Seriële poort(en):	4
LAN controller:	Intel® I350
Soorten RAID:	0, 1,6, 10, 50, 60
Geheugenbus:	72 Bit
Aantal SATA III connectors:	8
Compatibele processors:	Intel® Xeon®
Aantal ondersteunde processoren:	1
Intel® Xeon series:	E5-2600
Maximum UDIMM geheugen:	32 GB
Aantal DIMM sloten:	16
Aantal storage drives ondersteund:	16
Opslagschijf afmetingen ondersteund:	2.5 "
Ondersteunde geheugen types:	DDR4-SDRAM
Hot-swap HDD bays:	Ja
AC-ingangsspanning:	100 - 240 V
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	10 - 35 °C
Relatieve vochtigheid in bedrijf (V-V):	8 - 90 procent
Code geharmoniseerd systeem (HS):	84714100
Ventilator diameter:	80 mm
DC output stroom (+ 12 V):	75 A
IPMI LAN (RJ-45) port:	Ja
DC uitgangsstroom (+ 5 V):	4 A
Maximale cache:	45 MB