StarTech.com SM21BMU31CI3 Handleiding

StarTech.com Niet gecategoriseerd SM21BMU31CI3

Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com SM21BMU31CI3 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: May 15, 2019 2:18 PM

Product Diagram (SM21BMU31CI3)

Exterior

Component Function

1Drive-Tray Screws x 2 • Used to secure the in the Drive Tray

Enclosure.

2USB-C Cable • Used to connect the to the Enclosure Host

Computer.

Interior

Component Function

1M.2 NGFF B Key Drive

Connector • Used to connect the to the .Drive Enclosure

2Drive Length Holes

(x 2)

• Used to accommodate dierent drive lengths

(42 mm, 60 mm and 80 mm).

3Drive-Mount Screw/

Nut • Used to secure the to the .Drive Enclosure

M.2 NGFF SATA Enclosure | USB-C | USB 3.1 (10Gbps)

4Stando (not

displayed)

• Used to secure the to the Drive Enclosure

using either the 42 mm or 60 mm Drive

Length Holes.

Requirements

For the latest requirements, please visit www.startech.com/SM21BMU31CI3

• An available USB-C Port

• An M.2 NGFF SATA SSD

Installation

Installing a Drive

Warning! Drives should be handled carefully, especially when they’re transported. If

you’re not careful with your drives, you may lose data as a result.

1. Use a (included) to remove the (x 2) Phillips Head Screwdriver Drive-Tray Screws

from the . Enclosure

2. Carefully pull the out of the . Drive Tray Enclosure

3. Place the beside the and align the screw groove on the with Drive Drive Tray Drive

the on the .Adjustable Drive Length Holes Drive Tray

4. Use a to remove the .Phillips Head Screwdriver Drive-Mount Screw

Note: If the drive-mount hardware is already installed in the correct position, proceed

to step 9.

5. Align the with the correct according to the length of Stando Drive Length Hole

the .Drive

6. Insert the into the large part of the .Stando Drive Length Hole

Note: Make sure that the longer part of the stando is on the same side as the M.2

NGFF B Key Drive Connector.

7. Align the notches on the with the edges of the smaller part of the Stando Drive

Length Hole.

8. Slide the into the smaller part of the .Stando Drive Length Hole

9. Gently slide the connector on the (on a 30-degree angle) into the Drive M.2 NGFF B

Key Drive Connector Enclosure on the .

Note: Do not force the Drive into the enclosure, the connector on your drive is keyed so

that it only ts one way.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

IC Radiation Exposure Statement

This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 0.5cm

between the radiator and your body.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a two-year warranty.

For further information on product warranty terms and conditions, please refer to .

www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: fr.startech.com

DE: de.startech.com

ES: es.startech.com

NL: nl.startech.com

IT: it.startech.com

JP: jp.startech.com

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

2500 Creekside

Parkwy

Lockbourne, Ohio

43137

U.S.A.

If the OS is Windows, complete the following steps:Host Computer’s

Windows PC

1. On the tray, click the icon.Notication Safely Remove Hardware and Eject Media

2. Click the storage device that you want to remove.

3. When the message appears indicating that , it’s safe to remove the device

disconnect the drive.

If the OS is macOS, complete the following steps:Host Computer’s

macOS

1. Close any windows that list the contents of the drive.

2. On your desktop, click and drag the icon onto the icon on USB Storage Trash Can

your desktop.

3. Wait 5 seconds, then disconnect the drive.

10. Lightly push the down into position on the circuit board.Drive

11. Insert the through the screw notch on the and into the Drive-Mount Screw Drive

Stando.

12. Using a tighten the , being careful Phillips Head Screwdriver Drive-Mount Screw

not to over-tighten.

13. Slide the into the center grooves in the enclosure so that the Drive Tray USB-C Port

is facing outward.

14. Secure the in place by inserting two on either side.Enclosure Drive-Tray Screws

15. Tighten the screws, being carefully not to over-tighten.

Connecting a Drive to a Computer

When the enclosure is connected to the the OS will automatically install the Computer

necessary software.

Note: The enclosure does not require an external power supply, as it receives enough

power from the USB port that it is connected to.

• Connect the integrated to a USB-C port on the .USB-C Cable Host Computer

Disconnecting a Drive

Warning! If you remove the drive before you receive the notication that it’s safe to do

so, you could experience lost or corrupted data.

Product specificaties

Merk:	StarTech.com
Categorie:	Niet gecategoriseerd
Model:	SM21BMU31CI3
Kleur van het product:	Zwart
Gewicht:	95 g
Breedte:	110 mm
Diepte:	50 mm
Hoogte:	14 mm
Snoerlengte:	0.145 m
Gewicht verpakking:	110 g
Breedte verpakking:	168 mm
Diepte verpakking:	98 mm
Hoogte verpakking:	30 mm
Gebruikershandleiding:	Ja
LED-indicatoren:	Activity, Power
USB-connectortype:	USB Type-C
Type stroombron:	USB
Certificering:	REACH, CE, FCC
USB-versie:	3.2 Gen 2 (3.1 Gen 2)
Materiaal:	Aluminium
Duurzaamheidscertificaten:	RoHS
Plug and play:	Ja
Temperatuur bij opslag:	-20 - 50 °C
USB-aansluiting:	Ja
Mean time between failures (MTBF):	50000 uur
Inclusief schroeven:	Ja
Opslag schijfgrootte:	M.2 "
Ondersteunde opslagstationinterfaces:	M.2
Chipset:	JMicron - JMS580
Overdrachtssnelheid:	6 Gbit/s
Aantal storage drives ondersteund:	1
Bedrijfstemperatuur (T-T):	5 - 35 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 80 procent
Type product:	SDD-behuizing
Code geharmoniseerd systeem (HS):	84733080
Geïntegreerde USB-kabel:	Ja
Geslacht USB-connector:	Mannelijk
UASP-ondersteuning:	Ja
Inclusief schroevendraaier:	Ja