StarTech.com PEXUSB312A3 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com PEXUSB312A3 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: May 14, 2020 1:26 PM
Product Diagram (PEXUSB312A3)
Component Function
1USB-A Ports Used to connect a to USB Peripheral Device
the . USB Card
2Bracket Screws Used to the orSecure Low Prole Full Prole
Bracket USB Card.to the
3PCI Express Connector Used to connect the to the USB Card PCI
Express Slot Host Computer on the .
4SATA Power Connector
(Optional) Connect a 15 Pin SATA Power
Connector USB to provide extra power to the
Type-A Ports.
Requirements
For the latest requirements, please visit www.startech.com/PEXUSB312A3
Computer with an available PCI Express® slot (x4, x8, or x16)
(Optional) SATA Power Source
Tools
Small Phillips® Head Screwdriver
2-Port USB 3.1 Card | 10Gbps per port | 2x USB-A | PCIe
Hardware Installation
Installing the Low Prole Bracket
By default the is attached to the . Depending on your Full Prole Bracket USB Card
system conguration you may need to remove the and replace it Full Prole Bracket
with the (included).Low Prole Bracket
1. Using a (sold separately), remove the two Small Phillips Head Screwdriver Bracket
Screws Full Prole Bracket USB Card securing the to the .
2. Align the on the with the on the Screw Holes USB Card Screw Holes Low Prole
Bracket USB Card Screw Holes Low . Making sure the is sitting on top of the on the
Prole Bracket.
3. Insert the through the and into the on the Bracket Screws USB Card Screw Holes
Low Prole Bracket.
4. Using the , tighten the being Small Phillips Head Screwdriver Bracket Screws,
careful not to over-tighten.
Installing the USB Card
Warning: USB cards can be damaged by static electricity. Make sure that you are
properly grounded before you open the computer case or touch the . You USB Card
should wear an anti-static strap when you install any computer components. If an
anti-static strap is not available, discharge any built-up static electricity by touching
a large grounded metal surface for several seconds. Only handle the by its USB Card
edges and do not touch the gold connectors.
1. Turn o the and disconnect any that are Host Computer Peripheral Devices
connected (e.g. printer, external hard drives, etc.).
2. Unplug the from the back of the .Power Cable Host Computer
3. Remove the from the . Cover Host Computer’s Case
Note: Consult the documentation that came with the for details Host Computer
about how to remove the safely.Cover
4. Locate an open (x4, x8, or x16) and remove the corresponding PCI Express Slot
Metal Cover Plate Host Computer’s Case from the back of the .
5. Gently insert the into the open and fasten the USB Card PCI Express Slot Bracket
to the back of the .Host Computer’s Case
6. (Optional) Connect a from the to the 15 Pin SATA Power Connector Power Supply
SATA Power Connector USB Card on the .
2
1
3
4
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to .
www.startech.com/warranty
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
If product has an exposed circuit board, do not touch the product under power.
Mesures de sécuri
Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
Se il prodotto p2-ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
5. On the screen, select the How do you want to search for drivers Browse my
computer for driver software link.
6. Click on the link.Let me pick from a list of available drivers on my computer
7. Select, .USB xHCI Compliant Host Controller
USB xHCI Compliant Host Controller
8. Click the Button. Next
9. Click the button once the installation is complete.Close
Note: Connecting a separate to the will provide extra power Power Supply USB Card
to the for charging connected .USB-A Ports Devices
7. Place the back onto the . Cover Host Computer’s Case
8. Reconnect the to the back of the .Power Cable Host Computer
9. Reconnect all of the that were disconnected in step 1.Peripheral Devices
10. Connect to the on the .USB Peripheral Devices USB-A Ports USB Card
Software Installation
When the is installed the drivers should install automatically. If the drivers do USB Card
not automatically install, navigate to to download www.startech.com/PEXUSB312A3
the appropriate driver package.
1. Click on the tab, under , select the appropriate driver package for the Support Drivers
Operating System Host Computer running on the .
2. When you have downloaded and unzipped the driver. Click on the Installation Guide
PDF and follow the instructions.
Installing the Driver in Windows 7
1. If the dialog box appears on your screen, close the dialog box Found New Hardware
or click the button.Cancel
2. Navigate to the screen.Device Manager
3. On the list of installed devices, right-click on ASMedia USB3.1 eXtensible Host
Controller.
4. Select from the pop-up menu.Update Driver


Product specificaties

Merk: StarTech.com
Categorie: Niet gecategoriseerd
Model: PEXUSB312A3
Kleur van het product: Zwart
Gewicht: 78 g
Breedte: 120 mm
Diepte: 110 mm
Hoogte: 19 mm
Gewicht verpakking: 142 g
Breedte verpakking: 215 mm
Diepte verpakking: 145 mm
Hoogte verpakking: 30 mm
Temperatuur bij opslag: -20 - 60 °C
Intern: Ja
Ondersteunt Mac-besturingssysteem: Mac OS X 10.13 High Sierra, Mac OS X 10.14 Mojave, Mac OS X 10.15 Catalina, Mac OS X 11.0 Big Sur, Mac OS X 13.0 Ventura
Ondersteunt Linux: Ja
Snelle installatiehandleiding: Ja
Hostinterface: PCIe
Aantal poorten USB 3.2 Gen 2 (3.1 Gen 2) Type A: 2
Ondersteunde server operating systems: Windows Server 2012 R2, Windows Server 2016, Windows Server 2019
Montagebeugels meegeleverd: Ja
(Buitenste) hoofdverpakking hoogte: 370 mm
(Buitenste) hoofdverpakking breedte: 590 mm
(Buitenste) hoofdverpakking lengte: 315 mm
Hoeveelheid per (buitenste) hoofdverpakking: 80 stuk(s)
Bedrijfstemperatuur (T-T): 5 - 50 °C
Relatieve vochtigheid in bedrijf (V-V): 20 - 80 procent
Code geharmoniseerd systeem (HS): 84733020
Uitbreidingskaart vormfactor: Volledige hoogte / Laag profiel
Uitbreidingskaartstandaard: PCIe 3.0
Data transfer snelheid (max): 10 Gbit/s
Aantal Internal SATA ports: 1
Output interface: USB 3.2 Gen 2 (3.1 Gen 2)
Type SATA-voedingsconnector: SATA 15-pin

Heb je hulp nodig?

Als je hulp nodig hebt met StarTech.com PEXUSB312A3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd StarTech.com

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd