StarTech.com PEXUSB311AC3 Handleiding

StarTech.com Niet gecategoriseerd PEXUSB311AC3

Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com PEXUSB311AC3 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: May 14, 2020 2:21 PM

Product Diagram (PEXUSB311AC3)

Component Function

1USB-A Port • Used to connect a to USB Peripheral Device

the . USB Card

2USB-C Port • Used to connect a to USB Peripheral Device

the . USB Card

3Bracket Screws • Used to the orSecure Low Prole Full Prole

Bracket USB Card.to the

4PCI Express Connector • Used to connect the to the USB Card PCI

Express Slot Host Computer on the .

5SATA Power Connector

• (Optional) Connect a 15 Pin SATA Power

Connector to provide extra power to the USB

Ports.

Requirements

For the latest requirements, please visit www.startech.com/PEXUSB311AC3

• Computer with an available PCI Express® slot (x4, x8, or x16)

• (Optional) SATA Power Source

2-Port USB 3.1 Card - 10Gbps per port - USB-C, USB-A - PCIe

Tools

• Small Phillips Head Screwdriver

Hardware Installation

Warning: USB cards can be damaged by static electricity. Make sure that you are

properly grounded before you open your computer case or touch the . You USB Card

should wear an anti-static strap when you install any computer component. If an anti-

static strap is not available, discharge any built-up static electricity by touching a large

grounded metal surface for several seconds. Only handle the by its edges USB Card

and do not touch the gold connectors.

Installing the Low Prole Bracket

By default the is attached to the . Depending on your Full Prole Bracket USB Card

system conguration you may need to remove the and replace it Full Prole Bracket

with the (included).Low Prole Bracket

1. Using a , remove the two securing Small Phillips Head Screwdriver Bracket Screws

the to the .Full Prole Bracket USB Card

2. Align the on the with the on the Screw Holes USB Card Screw Holes Low Prole

Bracket USB Card Screw Holes Low . Making sure the is sitting on-top of the on the

Prole Bracket.

3. Insert the through the and into the on the Bracket Screws USB Card Screw Holes

Low Prole Bracket.

4. Using the , tighten the being Small Phillips Head Screwdriver Bracket Screws,

careful not to over-tighten.

Installing the USB Card

1. Turn o the and any that are connected (e.g., Computer Peripheral Devices

printers, external hard drives, etc.).

2. Unplug the from the back of the and disconnect any Power Cable Computer

Peripheral Devices that are connected.

3. Remove the from the . Cover Computer Case

Note: Consult the documentation that came with the for details about Computer

how to do this safely.

4. Locate an open (x4, x8, or x16) and remove the corresponding PCI Express Slot

Metal Cover Plate Computer Case from the back of the .

5. Gently insert the into the open and fasten the USB Card PCI Express Slot Bracket

to the back of the .Computer Case

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a two-year warranty.

For further information on product warranty terms and conditions, please refer to .

www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: startech.com/fr

DE: startech.com/de

ES: startech.com/es

NL: startech.com/nl

IT: startech.com/it

JP: startech.com/jp

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

2500 Creekside

Parkwy

Lockbourne, Ohio

43137

U.S.A.

7. Select, .USB xHCI Compliant Host Controller

USB xHCI Compliant Host Controller

8. Click the Button. Next

9. Click the button once the installation is complete.Close

6. Place the back onto the . Cover Computer Case

7. Reconnect the to the back of the .Power Cable Computer

8. Reconnect all of the that were disconnected in step 3.Peripheral Devices

9. Connect to the and on the .USB Peripheral Devices USB-C USB-A Ports USB Card

Software Installation

The drivers should install automatically, however, if they do not, you will need to

manually install the driver.

• Download the drivers from www.startech.com/PEXUSB311AC3. Click on the Support

tab, under , select the appropriate drive .zip le for the Drivers Operating System

running on the .Host Computer

Installing the Driver in Windows 7

1. If the dialog box appears on your screen, close the dialog box Found New Hardware

or click the button.Cancel

2. Navigate to the .Device Manager

3. On the list of installed devices, right-click on ASMedia USB3.1 eXtensible Host

Controller.

4. Select from the pop-up menu.Update Driver

5. On the screen, select the How do you want to search for drivers Browse my

computer for driver software link.

6. Click on the link.Let me pick from a list of available drivers on my computer

Product specificaties

Merk:	StarTech.com
Categorie:	Niet gecategoriseerd
Model:	PEXUSB311AC3
Kleur van het product:	Rood
Gewicht:	48 g
Breedte:	81 mm
Diepte:	120 mm
Hoogte:	19 mm
Gewicht verpakking:	123 g
Breedte verpakking:	170 mm
Diepte verpakking:	142 mm
Hoogte verpakking:	30 mm
Duurzaamheidscertificaten:	CE, RoHS
Temperatuur bij opslag:	-20 - 85 °C
Intern:	Ja
Aantal poorten USB 3.2 Gen 2 (3.1 Gen 2) Type C:	1
Ondersteunt Mac-besturingssysteem:	Mac OS X 10.13 High Sierra, Mac OS X 10.14 Mojave, Mac OS X 10.15 Catalina, Mac OS X 11.0 Big Sur, Mac OS X 12.0 Monterey, Mac OS X 13.0 Ventura
Naleving van duurzaamheid:	Ja
Ondersteunt Linux:	Ja
Snelle installatiehandleiding:	Ja
Mean time between failures (MTBF):	2684396 uur
Hostinterface:	PCIe
Aantal poorten USB 3.2 Gen 2 (3.1 Gen 2) Type A:	1
Ondersteunde server operating systems:	Windows Server 2008 R2, Windows Server 2012, Windows Server 2016, Windows Server 2019
Montagebeugels meegeleverd:	Ja
Chipset:	ASMedia - ASM3142
(Buitenste) hoofdverpakking hoogte:	500 mm
(Buitenste) hoofdverpakking breedte:	370 mm
(Buitenste) hoofdverpakking lengte:	365 mm
Hoeveelheid per (buitenste) hoofdverpakking:	60 stuk(s)
Bedrijfstemperatuur (T-T):	5 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 80 procent
Code geharmoniseerd systeem (HS):	84733020
Uitbreidingskaart vormfactor:	Volledige hoogte / Laag profiel
Uitbreidingskaartstandaard:	PCIe 3.0
Data transfer snelheid (max):	10 Gbit/s
Output interface:	USB 3.2 Gen 2 (3.1 Gen 2)
UASP-ondersteuning:	Ja