StarTech.com PEX8S1050 Handleiding

StarTech.com Niet gecategoriseerd PEX8S1050

Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com PEX8S1050 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: July 24, 2023 5:11 PM

Product Diagram (PEX8S1050)

Component Function

1DB62 Connector • Connects the 8-Port DB62 to DB9MX8

Breakout Cable Serial Adapter Card to the .

2PCI Express Connector • Used to connect the to Serial Adapter Card

the on the .PCI Express Slot Host Computer

3JP1 PME Jumper

• Used to enable or disable wake from sleep.

• ENA = Enables wake from sleep. Move the plug

to cover the and middle pins.ENA

• DIS = Disables wake from sleep. Move the plug

to cover the and middle pins.DIS

4J5 Aux Power

Connector

• Used to connect the Host Computers Power

Supply (4 Pin SP4/Floppy power connector).

5JP5 Aux Power Source

Selector

• Determines the voltage.DC Power Source

• X5V DC Power Source= 5V from a connected

to the .JP5 Aux Power Connector

• X12V DC Power Source = 12V from a

connected to the .JP5 Aux Power Connector

• I12V PCI Express Slot = 12V from

(motherboard’s PCIe slot).

6JP4 Power Over

External Connector

• Enables or disables the power over Pin #58

on the 8-Port DB62 to DB9MX8 Breakout

Cable’s DB62 Connector.

• GND Pin #58 = No power is supplied to on the

DB62 Connector.

• PWR Pin #58 = Power is supplied to on the

DB62 Connector DC Power Source when a is

connected to . J5 Aux Power Connector

8 Port PCI Express RS232 Serial Adapter Card 16C1050

Requirements

For the latest requirements, please visit www.startech.com/PEX8S1050

• Computer with an available PCI Express® slot (x1, x4, x8, or x16)

• (Optional) External DC Power Source - Host Computer’s PSU

• (Optional) DB62 to DB9MX8 Cable w/ Pin #58 as power source

Operating System (OS):

• Windows® 7, 8, 8.1, 10 and 11

Tools

• Small Phillips Head Screwdriver

Driver

• You must download and install the Systembase Drivers, see Downloading the

Drivers section.

Hardware Installation

Warning: Serial Adapter Cards can be damaged by static electricity. Make sure that you are

properly grounded before you open your computer case or touch the . Serial Adapter Card

Only handle the by its edges and do not touch the gold connectors.Serial Adapter Card

Installing the Serial Adapter Card

1. Turn o the and any that are connected (e.g., Computer Peripheral Devices

printers, external hard drives, etc.).

2. Unplug the from the back of the and disconnect any Power Cable Computer

Peripheral Devices that are connected.

3. Remove the from the . Cover Computer Case

4. Locate an open (x1, x4, x8, or x16) and remove the corresponding PCI Express Slot

Metal Cover Plate Computer Case from the back of the .

5. Gently insert the into the open and fasten the Serial Adapter Card PCI Express Slot

Bracket Computer Case to the back of the .

6. Place the back onto the . Cover Computer Case

7. Connect the 8-Port DB62 to DB9MX8 Breakout Cable ( ) DB62 included to the

Connector Serial Adapter Card.on the

Note: The the 8-Port DB62 to DB9MX8 Cable’s Connector shell/exterior is not

grounded.

8. Tighten the two screws on the sides of the , securing the . DB62 Connector Cable

9. Connect up to 8 serial devices to the on the DB9MX8 Connectors DB62 to DB9MX8

Breakout Cable.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a lifetime warranty.

For further information on product warranty terms and conditions, please refer to .

www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

StarTech.com Ltd.

45 Artisans Crescent

London, Ontario

N5V 5E9

Canada

StarTech.com LLP

4490 South Hamilton

Road

Groveport, Ohio

43125

U.S.A.

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Road

Brackmills,

Northampton

NN4 7BW

United Kingdom

StarTech.com Ltd.

Siriusdreef 17-27

2132 WT Hoofddorp

The Netherlands

FR: startech.com/fr

DE: startech.com/de

ES: startech.com/es

NL: startech.com/nl

IT: startech.com/it

JP: startech.com/jp

Pin Signal Pin Signal Pin Signal

1 TXD1 22 RXD1 43 CTS1

2 DTR1 23 DSR1 44 RTS1

3 RXD2 24 DCD1 45 GND

4 DSR2 25 TXD2 46 CTS2

5 DCD2 26 DTR2 47 RTS2

6 TXD3 27 RXD3 48 CTS3

7 DTR3 28 DSR3 49 RTS3

8 RXD4 29 DCD3 50 GND

9 DSR4 30 TXD4 51 CTS4

10 DCD4 31 DTR4 52 RTS4

11 RXD5 32 GND 53 CTS5

12 DSR5 33 TXD5 54 RTS5

13 DCD5 34 DTR5 55 GND

14 TXD6 35 RXD6 56 CTS6

15 DTR6 36 DSR6 57 RTS6

16 RXD7 37 DCD6 58 PWR

17 DSR7 38 TXD7 59 CTS7

18 DCD7 39 DTR7 60 RTS7

19 RXD8 40 GND 61 CTS8

20 DSR8 41 TXD8 62 RTS8

21 DCD8 42 DTR8

10. (Optional) Screw two (included) onto the two screws on the sides of the Hex Screws

DB9 Connector in order to attach/secure additional peripherals or another cable to

the .DB9 Connector

11. Reconnect the to the back of the and reconnected allPower Cable Computer

Peripheral Devices.

Downloading the Drivers

• When the is connected, you must download the Serial Adapter Card Systembase

Drivers from the tab - @ . Support Drivers www.startech.com/PEX8S1050

Connecting an External DC Power Source

• Connect the to the Host Computer’s Power Source Unit (PSU) 4 Pin SP4/Floppy

Power Connector Serial Adapter Card on the .

Pinout Diagram

Product specificaties

Merk:	StarTech.com
Categorie:	Niet gecategoriseerd
Model:	PEX8S1050
Kleur van het product:	Geel
Gewicht:	74 g
Breedte:	16 mm
Diepte:	105 mm
Hoogte:	120 mm
Gewicht verpakking:	672 g
Breedte verpakking:	190 mm
Diepte verpakking:	290 mm
Hoogte verpakking:	65 mm
Meegeleverde kabels:	Serie
Soort serieële aansluiting:	RS-232
Duurzaamheidscertificaten:	RoHS
Voldoet aan industriestandaarden:	16C1050 UART
Temperatuur bij opslag:	-40 - 75 °C
Intern:	Ja
Ondersteunt Linux:	Ja
Snelle installatiehandleiding:	Ja
Mean time between failures (MTBF):	160013 uur
Hostinterface:	PCIe
Ondersteunde server operating systems:	Windows Server 2003, Windows Server 2008 R2, Windows Server 2012, Windows Server 2016, Windows Server 2019
Seriële poort(en):	8
Chipset:	ASMedia - ASM1083, System Base - SB16C1058PCI
(Buitenste) hoofdverpakking hoogte:	315 mm
(Buitenste) hoofdverpakking breedte:	400 mm
(Buitenste) hoofdverpakking lengte:	510 mm
Hoeveelheid per (buitenste) hoofdverpakking:	14 stuk(s)
Bedrijfstemperatuur (T-T):	0 - 55 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Code geharmoniseerd systeem (HS):	84733020
FIFO (First In, First Out):	256 B
Output interface:	Serie
Maximum kabellengte:	0.5 m
Baud snelheid:	921.6 Kbit/s
Data bits:	5, 6,7, 8
Stop bits:	1, 1.5, 2
Parity bit:	Even, N,Odd
Flow Control type:	RTS/CTS, XON/XOFF