StarTech.com PEX1S1P950 Handleiding

StarTech.com Niet gecategoriseerd PEX1S1P950

Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com PEX1S1P950 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: November 2, 2020

Product Diagram (PEX1S1P950)

Front Angle View

Port Function

1Serial Port • Connect Serial Peripheral Devices

• DB-9 Parallel (Male)

2Jumper • Set the power output voltage for the Serial Port

3SATA Power Connector • Connect to a SATA Power Source

• (Optional) Power the Serial Port

4Parallel Port • Connect Parallel Peripheral Devices

• DB-25 Parallel (Female)

5PCIe Connector • Connect the to the in PCIe Card PCI Express Slot

the Computer

6Bracket • For full prole installations

Package Contents

• Serial and Parallel PCI Express Card x 1

• Full Prole Bracket (Installed) x 1

• Quick-Start Guide x 1

Requirements

For the latest requirements, please visit:

www.startech.com/PEX1S1P950.

• Computer with an available PCI Express slot (x1)

1S1P Native PCI Express Serial Parallel Combo Card with 16C950 UART

Hardware Installation

Warning: PCIe Cards can be damaged by static electricity. Make sure that the

Installer Computer Case is properly grounded before they open the or touch the PCIe

Card. The should wear an when installing any computer Installer Anti-Static Strap

component. If an is not available, discharge any built-up static Anti-Static Strap

electricity by touching a large for several seconds. Only Grounded Metal Surface

handle the by its edges and do not touch the gold connectors.PCIe Card

Jumper Conguration

Note: This is specially designed to allow for power output from the ninth PCIe Card

pin of the for that support power over serial. Serial Port Serial Devices Jumper

conguration is a requirement when connecting that require power Serial Devices

through the .Serial Port

The can be moved into one of three dierent positions in order to set the Jumper

power output voltage for the . The default setting for the is , no Serial Port Jumpers RI

power. The must be connected after conguring the SATA Power Connector Jumper

to or of power. To congure the , complete the following:5V 12V Jumper

1. Ensure the isComputer Power O.

2. Locate and carefully remove the . Lift the straight up and o of the Jumper Jumper

PCIe Card.

Notes: The is located on the left-hand side, labeled as on the Jumper Serial 1

. Printed Circuit Board

Always hold the by the edges.Card

3. Determine the power setting that is required for the .Serial Port

4. Position the over the set of that correspond with the desired Jumper Pins Serial

Connector Power Setting Jumper. See to determine where the Figure 1 should be

positioned.

Figure 1

Jumper

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a lifetime warranty.

For further information on product warranty terms and conditions, please refer to .

www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto p2-ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: fr.startech.com

DE: de.startech.com

ES: es.startech.com

NL: nl.startech.com

IT: it.startech.com

JP: jp.startech.com

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

4490 South Hamilton

Road

Groveport, Ohio

43125

U.S.A.

Software Installation

Driver Installation

You can download the latest from the StarTech.com website: Drivers

www.startech.com/PEX1S1P950.

Navigate to the tab to locate the . Follow the instructions Drivers/Downloads Drivers

included with the . Driver Files

5. Push the straight down and into place.Jumper

Note: Push the all the way into position for proper contact. Jumper

Installing the Card

1. Turn o the and any that are connected Computer Peripheral Devices

(e.g. printers, external hard drives, etc.).

2. Unplug the from the rear of the and disconnect any Power Cable Computer

Peripheral Devices that are connected.

3. Remove the from the . Cover Computer Case

Note: Consult the documentation that came with the for details about how Computer

to do this safely.

4. Locate an open and remove the corresponding PCI Express Slot Metal Cover Plate

from the rear of the . In most instances, the is Computer Case Metal Cover Plate

attached to the rear of the with a single . Save this for Computer Case Screw Screw

the next step.

5. Gently insert the into the open and fasten the to PCIe Card PCI Express Slot Bracket

the rear of the , using the from step 4. Computer Case Screw

6. Place the back onto the . Cover Computer Case

7. Reconnect all of the that were disconnected in step 2.Peripheral Devices

8. Connect a to the on the .Serial Device Serial Port PCIe Card

9. Connect a to the on the .SPP/EPP/ECP Peripheral Device Parallel Port PCIe Card

10. Reconnect the to the rear of the .Power Cable Computer

Product specificaties

Merk:	StarTech.com
Categorie:	Niet gecategoriseerd
Model:	PEX1S1P950
Kleur van het product:	Rood
Gewicht:	63 g
Breedte:	95 mm
Diepte:	80 mm
Hoogte:	22 mm
Gewicht verpakking:	127 g
Breedte verpakking:	170 mm
Diepte verpakking:	142 mm
Hoogte verpakking:	30 mm
Soort serieële aansluiting:	RS-232
Duurzaamheidscertificaten:	CE, RoHS
Temperatuur bij opslag:	-40 - 85 °C
Intern:	Ja
Ondersteunt Linux:	Ja
Mean time between failures (MTBF):	3188058 uur
Hostinterface:	PCIe
Ondersteunde server operating systems:	Windows Server 2003, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Seriële poort(en):	1
Chipset:	Asix - AX99100
(Buitenste) hoofdverpakking hoogte:	310 mm
(Buitenste) hoofdverpakking breedte:	380 mm
(Buitenste) hoofdverpakking lengte:	500 mm
Hoeveelheid per (buitenste) hoofdverpakking:	60 stuk(s)
Overdrachtssnelheid:	2.5 Mbit/s
Parallelle poort(en):	1
Bedrijfstemperatuur (T-T):	-40 - 85 °C
Relatieve vochtigheid in bedrijf (V-V):	15 - 90 procent
Code geharmoniseerd systeem (HS):	84733020
Uitbreidingskaartstandaard:	PCIe 2.0
FIFO (First In, First Out):	256 B
Output interface:	Parallel, Serial
Baud snelheid:	921.6 Kbit/s
Data bits:	5, 6,7, 8,9
Stop bits:	1, 1.5, 2
Parity bit:	Even, Mark, N,Odd, Space
Flow Control type:	N, RTS/CTS, XON/XOFF