StarTech.com PCI2S1P2 Handleiding

StarTech.com Niet gecategoriseerd PCI2S1P2

Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com PCI2S1P2 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: March 10, 2021

Product Diagram (PCI2S1P2)

Front View

Port Function

1Parallel Connector • Connect to the on the Parallel Pins PCI Card

2Low-Prole Bracket

(Parallel) • See Installing the Low-Prole Bracket(s)

3Parallel Port • Connect a Parallel Peripheral Device

• DB-25 Parallel (Female)

4Low-Prole Brackets

(Serial) • See Installing the Low-Prole Bracket(s)

5Serial Ports • Connect Serial Peripheral Devices

• DB-9 Parallel (Male)

6 PCI Connector • Connect the to the in the PCI Card PCI Slot

Computer

Package Contents

• PCI Serial Parallel Combo Card x 1

• Full-Prole Bracket (Installed) x 1

• Low-Prole Brackets (for Serial Ports) x 2

• Low-Prole Bracket (for Parallel Port) x 1

• Quick-Start Guide x 1

2S1P PCI Serial Parallel Combo Card with 16C550 UART

Requirements

For the latest requirements, please visit:

www.startech.com/PCI2S1P2.

• Computer with an available PCI slot (x4/8/16)

• Needle-nose Pliers or 3/16 Nut Driver

Hardware Installation

Warning: PCI Cards can be damaged by static electricity. Make sure that the

Installer Computer Case is properly grounded before they open the or touch the PCI

Card. The should wear an when installing any computer Installer Anti-Static Strap

component. If an is not available, discharge any built-up static Anti-Static Strap

electricity by touching a large for several seconds. Only Grounded Metal Surface

handle the by its edges and do not touch the gold connectors. PCI Card

Installing the Low-Prole Bracket(s)

By default the is attached to the . Full-Prole Bracket Serial/Parallel Port(s)

Depending on the system conguration it may be necessary to remove the Full-

Prole Bracket(s) Low-Prole Bracket(s) to replace with the (included).

1. Remove the from both sides of each , using a Hexagonal Standos Port 3/16 Nut

Driver Needle-nose Pliersor a pair of .

2. Remove the and replace with the .Full-Prole Bracket(s) Low-Prole Bracket(s)

3. Install the removed in step 1. Thread the Hexagonal Standos Hexagonal

Standos Threaded Post 3/16 Nut Driver onto each and tighten, using a or a pair

of .Needle-nose Pliers

Installing the Card

1. Turn o the and any that are connected Computer Peripheral Devices

(e.g. printers, external hard drives, etc.).

2. Unplug the from the rear of the and disconnect any Power Cable Computer

Peripheral Devices that are connected.

3. Remove the from the . Cover Computer Case

Note: Consult the documentation that came with the for details about Computer

how to do this safely.

4. Locate an open and remove the corresponding from the PCI Slot Metal Cover Plate

rear of the . In most instances, the is attached Computer Case Metal Cover Plate

to the rear of the with a single . Save this for the next Computer Case Screw Screw

step.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a lifetime warranty.

For further information on product warranty terms and conditions, please refer to .

www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: startech.com/fr

DE: startech.com/de

ES: startech.com/es

NL: startech.com/nl

IT: startech.com/it

JP: startech.com/jp

StarTech.com Ltd.

45 Artisans Crescent

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Road

Brackmills,

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

4490 South Hamilton

Road

Groveport, Ohio

43125

U.S.A.

StarTech.com Ltd.

Siriusdreef 17-27

2132 WT Hoofddorp

The Netherlands

Software Installation

Driver Installation

This product requires a driver to be installed on the . Download the Host Computer

latest from the StarTech.com website: Drivers

www.startech.com/PCI2S1P2.

Navigate to the tab to locate the . Follow the instructions Drivers/Downloads Drivers

included with the . Driver Files

5. Gently insert the into the open and fasten the to the rear PCI Card PCI Slot Bracket

of the , using the from step 4. Computer Case Screw

6. Locate a second open and remove the corresponding PCI Slot Metal Cover Plate

from the rear of the . In most instances, the is Computer Case Metal Cover Plate

attached to the rear of the with a single . Save this for Computer Case Screw Screw

the next step.

7. Fasten the to the rear of the , using the Bracket (Parallel) Computer Case Screw

from step 6.

8. Place the back onto the . Cover Computer Case

9. Reconnect all of the that were disconnected in step 2.Peripheral Devices

10. Connect a to the on the .Serial Device Serial Port PCI Card

11. Connect a to the on the .SPP/EPP/ECP Peripheral Device Parallel Port PCI Card

12. Reconnect the to the rear of the .Power Cable Computer

Product specificaties

Merk:	StarTech.com
Categorie:	Niet gecategoriseerd
Model:	PCI2S1P2
Kleur van het product:	Zwart
Gewicht:	141 g
Breedte:	21.6 mm
Diepte:	134 mm
Hoogte:	120 mm
Gewicht verpakking:	190 g
Breedte verpakking:	142 mm
Diepte verpakking:	170 mm
Hoogte verpakking:	30 mm
Gebruiksaanwijzing:	Ja
Soort serieële aansluiting:	RS-232
Duurzaamheidscertificaten:	CE, RoHS
Temperatuur bij opslag:	-20 - 85 °C
Intern:	Ja
Ondersteunt Linux:	Ja
Hostinterface:	PCI/PCI-X
Ondersteunde server operating systems:	Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016, Windows Server 2019
Montagebeugels meegeleverd:	Ja
Seriële poort(en):	2
Chipset:	Asix - MCS9865
(Buitenste) hoofdverpakking hoogte:	340 mm
(Buitenste) hoofdverpakking breedte:	360 mm
(Buitenste) hoofdverpakking lengte:	385 mm
Hoeveelheid per (buitenste) hoofdverpakking:	40 stuk(s)
Bedrijfstemperatuur (T-T):	0 - 70 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Code geharmoniseerd systeem (HS):	84733020
Uitbreidingskaart vormfactor:	Volledige hoogte / Laag profiel
FIFO (First In, First Out):	256 B
Data transfer snelheid (max):	0.0015 Gbit/s
Output interface:	Serie
Baud snelheid:	115.2 Kbit/s
Data bits:	5, 6,7, 8,9
Stop bits:	1, 1.5, 2
Parity bit:	Even, Mark, N,Odd, Space
Flow Control type:	N, RTS/CTS, XON/XOFF