StarTech.com AP150WN1X1U Handleiding

StarTech.com Access point AP150WN1X1U

Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com AP150WN1X1U (2 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick Start Guide

Manual Revision: 01/27/2014

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

I T: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

P T: Guia do usuário - pt.startech.com

Packaging Contents

• 1 x Travel Router

• 1 x USB Cable

• 1 x RJ45 Cable

• 1 x Carrying Pouch

• 1 x Instruction Manu

System Requirements

• Available USB port (or wall charger) for power

AP150WN1X1U

Portable 150Mbps Wireless N Travel Router / Access Point - USB Powered

WPS / Reset Button

WPS

WPS mode is disabled by default because it requires a secured wireless network to be

used.

1. Once you have selected an operating mode and are connected to the

web interface (details in the following sections of this manual), congure

your desired wireless security protocol and key.

LED Indicators

WiFi

O: No Wi-Fi signal

Solid: Wi-Fi signal broadcasting

Flashing: Activity

WLAN

O: No RJ45 connection detected

Solid: RJ45 connection detected

Flashing: Activity

POWER O: No power supplied to the device

Solid: Connected to a USB power source

2. Enable WPS mode.

3. Once enabled, a single press of the button will activate it.

Reset

In order to reset the device to factory defaults:

Note: All previously congured settings will be deleted after performing a reset

1. Ensure the AP is connected to a power source.

2. Press and hold the reset button for 8 seconds, then release.

Installation

Please visit www.startech.com/AP150WN1X1U for full operating instructions and

specications

Default Settings

SSID: AP150WN1X1U

LAN IP Address: 192.168.16.254

Username / Password: admin / admin

Wireless Access Point

In AP mode, the AP150WN1X1U acts as a wireless transmitter which adapts a wired

network signal into WiFi, so that other wireless devices like smartphones and tablets

within range can share the wired connection.

Widely used in: Hotel rooms, school dormitories, etc.

1. Adjust the switch on the device to AP Mode.

2. Connect one end of the included Ethernet cable to the RJ45 port of the AP, and

the other to the hotel wall jack/switch.

3. Connect one end of the included USB cable to the USB port of the AP, and the

other to a USB power source (e.g. laptop, USB wall charger, etc.).

4. Connect your wireless devices to the “AP150WN1X1U” SSID and open your web

browser to access the Internet.

NOTE: If the hotel Internet connection requires a password or has a captive portal

RJ45 Interface WPS/Reset Button Mode Selector Switch USB Interface

Product Overview

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of

their respective holders.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation

of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Déclaration d’exposition à la radiation: Cet équipement respecte les limites d’exposition aux rayonnements IC dénies pour un environnement non contrôlé. Cet équipement doit être installé et mis en marche à une distance minimale de 20 cm qui sépare l’élément rayonnant de

votre corps. L’émetteur ne doit ni être utilisé avec une autre antenne ou un autre émetteur ni se trouver à leur proximité.

FCC ID: X2NBL-MP02

IC: 11232A-AP150WN1X1U

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two year warranty.

In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement withequivalent products at our discretion. The

warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss,

arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Wireless Router

In RT mode, the AP150WN1X1U acts as a wireless router to create a wireless signal

from a cable or DSL modem provided by an Internet Service Provider (ISP). This allows

multiple wireless devices to use a wired connection that normally only allows one

device to connect.

1. Adjust the switch on the device to RT Mode.

2. Connect one end of the included Ethernet cable to the RJ45 port of the AP, and the

other to the cable / DSL Modem.

3. Connect one end of the included USB cable to the USB port of the AP, and the

other to a USB power source (e.g. laptop, USB wall charger, etc.).

4. Connect a wireless device to the “AP150WN1X1U” SSID, which will open your

default web browser to access the conguration page.

Note: If your web browser does not open automatically, open your preferred browser

and enter the default IP address 192.168.16.254 into the address bar.

5. Enter the username / password when prompted, to access the conguration page

(Default: admin / admin).

6. Congure your required WAN and Wireless settings:

a. WAN Setup: Enter in your ISP username / password (typically required for DSL, not

cable) and connection type (contact your ISP for further information if required).

b. Wireless Setup: Congure your desired SSID and Security type / Key, and click Apply

when nished.

WiFi Repeater

In Repeater mode, the AP150WN1X1U acts as a wireless card that can amplify, relay

and extend the range of a weak wireless signal.

Widely used in: Large buildings, large rooms, etc.

1. Adjust the switch on the device to Repeater Mode.

2. Connect one end of the included USB cable to the USB port of the AP, and the

other to a USB power source (e.g. laptop, USB wall charger, etc.).

3. Connect a wireless device to the “AP150WN1X1U” SSID, which will open your

default web browser to access the conguration page.

Note: If your web browser does not open automatically, open your preferred browser

and enter the default IP address 192.168.16.254 into the address bar.

4. Enter the username / password when prompted, to access the conguration page

(Default: admin / admin).

5. From the site survey list, choose the desired SSID you would like to extend /

amplify and click Connect.

Note: If your desired SSID does not appear in the list, click the Rescan button.

Product specificaties

Merk:	StarTech.com
Categorie:	Access point
Model:	AP150WN1X1U
Kleur van het product:	Zwart
Gewicht:	68 g
Breedte:	28 mm
Diepte:	82 mm
Hoogte:	13 mm
Gewicht verpakking:	112 g
Breedte verpakking:	140 mm
Diepte verpakking:	175 mm
Hoogte verpakking:	30 mm
Materiaal behuizing:	Kunststof
LED-indicatoren:	Power, WLAN
Bedrijfsmodi:	Access Point (AP), Repeater, Router
USB-connectortype:	Mini-USB B
Frequentieband:	2.4 - 2.4835 GHz
Meegeleverde kabels:	LAN (RJ-45), USB
Snelstartgids:	Ja
Aantal USB 2.0-poorten:	1
Aantal Ethernet LAN (RJ-45)-poorten:	1
Certificering:	CE, FCC, RoHS
Modulatie:	16-QAM, 64-QAM, CCK, DBPSK, DQPSK, OFDM
Ethernet LAN, data-overdrachtsnelheden:	10, 100 Mbit/s
Netwerkstandaard:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3u
Ondersteunde beveiligingsalgoritmen:	WEP, WPA, WPA2, WPA2-PSK
Soort antenne:	Intern
Aantal gebruikers:	5 gebruiker(s)
Temperatuur bij opslag:	-40 - 70 °C
Intern:	Nee
Web-gebaseerd management:	Ja
Maximale overdrachtssnelheid van gegevens:	150 Mbit/s
2,4 GHz:	Ja
Maximum indoorbereik:	10 m
WAN-poort:	Ethernet (RJ-45), Wi-Fi
WPS Push Button Security:	Ja
AC-ingangsspanning:	100 - 240 V
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent