Springfree Medium Square S72 Handleiding

Springfree Niet gecategoriseerd Medium Square S72

Lees hieronder de 📖 handleiding in het Nederlandse voor Springfree Medium Square S72 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
A
C
D
B
WANTTO MPJU ?DO
ITSAFE! ONE ATA TIME.
E EDE SAU TER?FAITES EENTOU TE URITÉ! UNE À LA SNVI -L SÉC FOI
MAT
DIAMETER
9  x 9  (2.75 m x 2.75 m)
MAXIMUM USER
WEIGHT
220 lbs (100 kg)
MAT HEIGHT FROM
GROUND
3  (0.9 m)
MINIMUM NET HEIGHT
FROM MAT
6  (1.8 m)
The information in this document is subject to change without notice.
© Copyright Springfree® Trampoline Inc. 2005, 2021. All rights reserved.
766401
Lay out the mat with the gray banding facing upwards inside the trampoline frame.
The blue tags on the mat should approximately align with the blue stickers on the frame.
Before moving to the next step, ensure that the mat rod holders are correctly positioned with the mat rod
holder tab outside the mat rod holder pocket, as per the insert. If the mat rod holder tab is inside the
pocket, adjust accordingly.
GE F H
Assembly and Disassembly Instructions
for Trampoline and Enclosure
1
ASSEMBLY
Lay out the parts as shown.
Qua ity Part Qu titynt an
1
52
1
Part
Mat
Mat Rods
Net
A.
B.
C.
Net Rods
Spare Small Bolt & Nut
Spare C-clips
12
1
3
D.
E.
F.
ROD INSTALLATION
TECHNIQUE Please read before continuing. DO NOT INSTALL
any of the mat rods yet.
6a
ASSEMBLY
5
ASSEMBLY
4
ASSEMBLY
3
ASSEMBLY
2
ASSEMBLY
Qua ity Part Qu titynt an
4
4
8
8
Part
Curved Frame Sections
Straight Frame Sections
Legs
Center Posts
A.
B.
C.
D.
Wrenches
C-clips (Attached to Frame)
Small Bolts & Nuts
Large Bolts & Nuts
2
12
16
8
E.
F.
G.
H.
TIP - Fastening the final two frame sections oen requires additional eort. Two people are
required for assembly.
TIP - When installing the legs, it is easiest when one person to holds the frame up and horizontal
while the other person inserts the legs into the leg sockets.
Position the frame sections together.
Connect and fasten frame sections using the large nuts and bolts. When finished, the bolt head should be
flush with the frame and the nut should face the center of the trampoline.
Attach a center post to the middle of each leg section.
Then, in the order shown, carefully li the frame and evenly insert the legs into the leg sockets on the
underside of the frame.
Fasten each leg to the frame using the small nuts and bolts before going to the next leg.
WARNING - Use the tools provided to fasten the nuts. Do not over tighten the nuts. The use of
power tools may cause serious damage to the trampoline.
Lay out the remaining parts as shown. The colored stickers all face upwards.
If you are missing any parts please contact Springfree Trampoline directly.
The Maximum User Weight for this
trampoline is located on the front
panel of this manual. Jumpers at or
near the Maximum User Weight
should take extra precautions in their
manoeuvres to ensure they do not
initiate contact with the ground while
jumping as this can cause serious
injury.
KG
LBS
Entrapment and choking hazard
possible for children under 6 years of
age.
0-6
No more than one person at a time.
Multiple jumpers increase the chances
of loss of control and collision and can
result in serious head, neck, back, leg,
arm or other injuries.
Treat any loaded rod with caution
until you are sure it is properly
installed or uninstalled. Keep face
clear of loaded rods. An improperly
installed rod could release and cause
facial injury or blindness.
Never remove a net rod from its net
rod pocket or disengage (unlock) the
metal joiner while the net rod is under
tension.
No somersaults or flips. Landing on
the head or neck can cause serious
injury, paralysis, or death, even when
landing in the middle of the bed.
Do not hold onto, or place fingers
between the rods while someone is
jumping on the trampoline.
If you anticipate severe weather,
consider lowering the enclosure,
moving the trampoline to a sheltered
location or disassembling the
trampoline completely.
WARNING Read the warnings on this page and those
contained in the User Guide before you assemble
and use the trampoline and enclosure.
Two people are recommended for assembly.
Keep small children at least 25  (7.5 m) away
while assembling the trampoline; they could
be injured by improperly assembled rods
releasing and ejecting from the frame.
Do not attempt to use the trampoline until it is
completely assembled.
Be aware that when loaded, the rods can
spring back and may cause injury. Keep your
face well clear of the rods during assembly or
disassembly. An improperly installed rod could
release and cause facial injury or blindness.
The sleeves on the rods are intended to
provide protection from fibers or splinters. Do
not remove. If they are damaged, replace
them.
Maintain a minimum clearance of 16.5  (5 m)
above the mat [in USA and Canada, 24  (7.3
m) above the trampoline from ground level] in
order to prevent users from inadvertently
contacting overhead hazards such as electric
wires, tree limbs, clotheslines or ceilings.
Maintain a minimum clearance of 5  (1.5 m)
[in EU countries, 6.5  (2.0 m)] on all sides of
the trampoline. This area should not include
concrete, bitumen, brick or other hard surfaces
or be in the proximity of other conflicting
installations (e.g. pools, swings, slides, climb-
ing frames) as these can cause serious injuries
if users fall o the trampoline.
A.
B.
C.
D.
E.
F.
G.
Do not locate the trampoline on top of other
objects or store anything underneath the
trampoline bed.
Place the trampoline in a well-lit area.
Only use approved Springfree® Trampoline
accessories, and install in accordance to
installation instructions. Do not make modifi-
cations to the trampoline or accessories.
Secure the trampoline against unauthorized
and unsupervised use.
The owner and supervisors of the trampoline
are responsible to make all users aware of
practices specified in the User Guide.
Trampoline enclosure is supplied as part of the
trampoline. Do not install enclosures that are
not suited to your product.
The trampoline is intended for indoor/outdoor
usage. Refer to Trampoline location informa-
tion in the User Guide for more details.
Use only with mature, knowledgeable supervi-
sion. Enforce all safety rules.
Record the purchase date of your trampoline
on the net serial number tag. It is located
under the net warnings, which are sewn into
the edge of the net next to the entrance.
H.
I.
J.
K.
L.
M.
N.
O.
P.
WARNING Please read the following precautions carefully
before beginning the assembly process. Retain
for future reference.
We encourage you to register your Springfree
Trampoline. Doing so will create a customer profile
which will allow us to provide future support and to
send you important product notifications.
http://springfr.ee/wclaim
E F
Outside Person:
Hold the mat rod near the ball end with your palm
facing up and bend your arm at a right angle as
shown.
Hold the mat edge with your other hand.
Pull your elbow into your hip and always push
using your body weight.
Inside Person:
Hold the mat rod with both hands as shown to
assist the outside person.
C
A
B
D
3
4
1
2
7
8
5
6
IMPORTANT
Easy step-by-step
3D interactive instructions
for this product can be found in
DOWNLOAD THE FREE APP
Locate the green tag on the bottom edge of the net and match it with any green sticker on your
trampoline frame.
Holding the net so that the green tag is facing you, gently place the rest of the net inside the frame as
shown. DO NOT let go of the green tag.
Put a mat rod through the hole to the immediate le of the green tag in the net and then into the mat
rod socket next to the green sticker.
Then, working carefully around the frame, insert the remaining mat rods through the net holes and into
the corresponding mat rod socket. When finished, the net should be stretched tightly around the OUTSIDE
of the frame.
Be sure that the mat rods are seated down to the bottom of each mat rod socket.
NOTE - As you install the mat rods into the mat rod sockets the net will become tight against the
frame. Handle the net with care and be sure that it does not get caught or it may tear.
NOTE - The net must be installed BEFORE installing the mat.
WARNING - Do not use the trampoline until it is completely assembled. Failure to follow these
instructions may cause rods to break or eject from the trampoline frame.
NOTE - Check that the net is not caught on the trampoline frame or the bolts or under the legs; if
the net catches, it may tear.
Moving clockwise around the frame, carefully slide the net up to the top of the mat rods.
Then, starting at one of the blue stickers on the curved frames, gently and slowly pull the net up and over
the edge of the mat. It is normal for the net to be tight. Take extra care not to tug the net and check that
the net is not snagged on the trampoline frame or the bolts.
Working slowly around the frame, carefully li the rest of the net over the edge of the mat until the bottom
band of the net is pulled all the way to the top of the mat rods.
NOTE - If you purchased a FlexrHoopTM with your trampoline, you could stop and install it right
now. This will save you a couple of steps later.
WARNING - Treat any loaded rod with caution until you are sure it is properly installed or
uninstalled. Keep your face well away from any loaded rod.
Assemble the net rods as shown.
Locate the pockets at the top edge of the net and install all of the net rods.
Take care to fully push the ball of the net rod into the pocket as shown. There is an internal catch at the
top of the pocket and the ball must be pushed past this internal catch or else it will come out. You will
feel some resistance as the ball is pushed through.
8
ASSEMBLY
9
ASSEMBLY
Unfold
an aligd n
1
Secure
2
WA DO TINT T ?O JUMP IT ! ONE T A SAFE A ME.
ENVIE E D S A U R? FA S EN TOU RITÉ ! À A .TE ITE -LE TE S ÉCU UNE L FOIS
WA SAFENT TO JUMP? IT DO !ONE T A ME. A TI
ENVIE E D S A U R? FA S EN TOU RITÉ ! À A .TE ITE -LE TE S ÉCU UNE L FOIS
10
ASSEMBLY MAT ROD REMOVAL
Outside Person:
When you remove a rod from the mat, do not twist
or rotate the mat edge. This could cause serious
injury or damage the trampoline.
Hold the mat edge flat with your le hand as
shown. Push up behind the mat rod holder tab
without obstructing the opening. This prevents
the ball from catching in the mat.
Hold the mat rod near the ball end with your palm
facing up and bend your arm at a right angle as
shown.
Pull your elbow into your hip and always push
using your body weight.
Inside Person:
Hold the mat rod with both hands as shown to
assist the outside person.
WARNING - Treat any loaded rod with caution until you are sure it is properly installed or
uninstalled. Keep your face well away from any loaded rod.
WARNING - Both people must maintain a steady grip on the rod until it is in its resting position.
Outside Person:
Push the mat rod out of the mat rod holder,
guiding the ball along the path shown.
In one swi movement:
1. Up and forward into the mat underside, out of
the mat rod holder.
2. Down and away from the mat underside.
3. Back towards you, easing it to a resting position.
Inside Person:
Pull the mat rod to assist the outside person in
guiding the ball up and out of the mat rod holder.
Maintain a steady grip until the ball is securely
removed from the mat rod holder.
NOTE - Following the sequence shown maintains the tension evenly across the mat. If you do not
follow this sequence, it will be very diicult to remove the mat.
WARNING - Treat any loaded rod with caution until you are sure it is properly installed or
uninstalled. Keep your face well away from any loaded rod.
Moving clockwise between the blue tag locations, remove every other installed mat rod (remove one,
skip one). Do NOT remove the mat rods at the blue tag locations.
Repeat the above step (removing every other installed mat rod), several times around the trampoline,
until only the mat rods at the blue tag locations remain.
Continue clockwise removing the final mat rods at each of the blue tag locations. Pulling the mat edge
while pushing the rod will be required to uninstall these rods.
Remove the mat rods from the frame and then pack the net, mat and rods.
Disassemble the frame in the reverse order to which it was assembled.
TOP VIEW
ROD REMOVAL
TECHNIQUE Please read before continuing. Do not remove
any of the mat rods yet.
2a
DISASSEMBLY ROD REMOVAL
TECHNIQUE Please read before continuing. Do not remove
any of the mat rods yet.
2b
DISASSEMBLY
3
DISASSEMBLY
TOP VIEW
1
DISASSEMBLY
WARNING - Treat any loaded rod with caution until you are sure it is properly installed or
uninstalled. Keep your face well away from any loaded rod.
NOTE - Following the sequence shown spreads the tension evenly across the mat. If you do not
follow this sequence, it will be very diicult to attach the mat.
Check that the center post of every leg is correctly seated under the trampoline frame. If they are not,
adjust them now.
Check every mat rod holder tab is outside the mat rod holder pocket.
At position find the blue sticker on the frame and the blue tag on the mat.
Install the mat rod at the blue sticker location into the mat rod holder at the blue tag location.
Repeat at position . Pulling the mat edge while pushing the mat rod will be required to install this
second rod.
Continue installing one rod at each of the remaining positions .
Move to Step 7b.
1
2
3 4 5 6 7 8
WARNING - Treat any loaded rod with caution until you are sure it is properly installed or
uninstalled. Keep your face well away from any loaded rod.
NOTE - Following the sequence shown spreads the tension evenly across the mat. If you do not
follow this sequence, it will be very diicult to attach the mat.
Complete Step 7a before continuing.
Start at any blue tag location and install two additional mat rods into the mat rod holders: one to the
right and one to the le of the already installed mat rod.
Move clockwise to the next blue tag location and repeat the above step.
Continue clockwise installing two additional mat rods at every blue tag location, several times around
the trampoline, until all of the rods are installed.
TOP VIEW
FIRST ROD INSTALL REMAINING ROD INSTALL
7a
ASSEMBLY
7b
ASSEMBLY
TIP - Keep the mat level when you install or uninstall the mat rods.
TIP - If you need to uninstall a mat rod, see the Disassembly Instructions.
Outside Person:
Push the mat rod, guiding the ball along the path
shown, into the mat rod holder.
In one swi movement:
1. Forward and under the mat rod holder.
2. Up until the ball hits the mat underside.
3. Back towards you, guiding the ball into the mat
rod holder.
Inside Person:
Pull the mat rod to assist the outside person in
guiding the ball.
Maintain a steady grip until the ball is securely
installed in the mat rod holder.
ROD INSTALLATION
TECHNIQUE Please read before continuing. DO NOT INSTALL
any of the mat rods yet.
6b
ASSEMBLY
To install the net, raise the net rods and carefully flex the bottom of the rods into the corresponding net
rod socket on the trampoline frame. Take care to completely insert the net rod into the socket. You will
hear a click when the net rod is fully seated.
Ensure the sleeve does not slide down the net rod as this prevents the c-clip from engaging the groove at
the bottom of the net rod.
For increased stability, your trampoline comes with sandbags. Fill these with sand and place over the
trampoline legs as required.
Congratulations! You have successfully installed your trampoline. Happy bouncing!
WARNING - Never remove a net rod from its net rod pocket or disengage (unlock) the metal joiner
while the net rod is under tension. First, remove the net rod from the net rod socket on the frame.
Always ensure a solid grip when handling and do not stand directly in front of the rods.
WARNING - Do not remove the legs until the end of the last step. Failure to follow these steps in
the correct order could cause serious injury or damage the trampoline.
WARNING - Never remove a net rod from its net rod pocket or disengage (unlock) the metal joiner
while the net rod is under tension. First, remove the net rod from the net rod socket on the frame.
Always ensure a solid grip when handling and do not stand directly in front of the rods.
Outside Person:
Remove the c-clips located on the net rod sockets.
Li the bottom end of the net rods out of the net
rod sockets and lower the net.
Remove the net rods from the net rod pockets and
lay them flat on the ground.
Replace the c-clips in the net rod sockets to keep
them safe.
Starting at a corner, carefully pull the top edge of
the net down over the edge of the mat. Continue
around the trampoline until the net is sitting at the
bottom of the mat rods.
17
3
5
4
82
6

Product specificaties

Merk: Springfree
Categorie: Niet gecategoriseerd
Model: Medium Square S72

Heb je hulp nodig?

Als je hulp nodig hebt met Springfree Medium Square S72 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Springfree

Springfree

Springfree Medium Square S72 Handleiding

27 Juli 2023
Springfree

Springfree Compact Oval O47 Handleiding

27 Juli 2023
Springfree

Springfree Small Round R30 Handleiding

27 Juli 2023
Springfree

Springfree Jumbo Round R132 Handleiding

19 Maart 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

V-Tac

V-Tac VT-44104 Handleiding

5 November 2024
V-Tac

V-Tac VT-44100CCT Handleiding

5 November 2024
MSW

MSW -HRH-600 Handleiding

5 November 2024
MSW

MSW -PCJ-302 Handleiding

5 November 2024
MSW

MSW -ETT-22 Handleiding

5 November 2024
DoorBird

DoorBird MTM56A Handleiding

5 November 2024
Hacienda

Hacienda PWB801 Handleiding

5 November 2024
Hacienda

Hacienda PWB802 Handleiding

5 November 2024
MSW

MSW -ECF1-01 Handleiding

5 November 2024
MSW

MSW -MWC-01 Handleiding

5 November 2024