Speco Technologies P16S18G Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Speco Technologies P16S18G (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
1 2
P16S18G - 16- - - Port Gigabit PoE + 2 Port Gigabit SFP + 2 Port Gigabit Copper Ethernet Switch
User Manual
Packing List
Open the product box and carefully unpack all contents box should contain the following items. . The
Please check before installation, if any missing, please contact your distributor immediately. are
Items Quantity
Switch 1 pc
AC Power Cable 1 pc
Mounting Accessories 1 set
Quick Installation Guide 1 pc
Product Introduction
This providswitch es sixteen - -Gigabit Ethernet RJ 45 downlink ports, two Gigabit Ethernet RJ 45 uplink
ports and two Gigabit SFP uplink ports. All RJ 45 downlink ports support Power Ethernet (PoE+) - -over-
and deliver up to 30W power per port.
The switches in three modes: default, VLAN, and flow control. It can be widely used in video work
security monitoring systems, network projects, etc.
Hardware Introduction
Dimensions (mm)
────────
16-Port Gigabit PoE + 2-Port Gigabit SFP + 2-Port Gigabit Copper Ethernet Switch
Front Panel (16 Port PoE Switch)-
Rear Panel (16- Port PoE Switch)
Led Indicators
Indicators Descriptions Status
Power Power Supply Indicator
On The Main Power Supply is working.
Off The Main Power Supply is off.
Link Port Link Indicator
On The port is linking normally.
Blink The port is transmitting or receiving data.
Off The port links down.
PoE Port PoE Indicator
On The port is supplying PoE normally.
Off The port stopped supplying PoE.
DIP Switch
Status Descriptions
Default Default mode. All ports are free to communicate
VLAN Downlink ports are isolated from each other, but can communicate with uplink ports
Flow control E s nable flow control function, this mode is suitable for video surveillance transmission
Note:
After changing the mode, please power on the device again to enter the corresponding mode.
16 Gigabit PoE + 2-Port -Port Gigabit SFP + 2-Port Gigabit Copper Ethernet Switch
───────
────────
16-Port Gigabit PoE + 2-Port Gigabit SFP + 2-Port Gigabit Copper Ethernet Switch
3 4
Installation Steps
1) Before installation, please disconnect the power supply of each signal source and equipment. Live
installation may damage the transmission equipment.
2) The switch supports 19-inch rack, desktop and wall-mounted installations. Users can install the
switch in a rack, or place it on a clean, stable, grounded workbench, or on a vertical, stable wall.
The 19-inch rack installation steps are shown in the following table:
Step 1: Fix the hangers on the side of the switch.
Accessories
2*
8*
Step 2: Install the switch on the rack with screws in the package.
Accessories
4*
Step 3: Continue to install other devices in the rack. The distance
between the devices should be more than 5cm.
Accessories
N/A
3) After step 2) is completed, please use Cat5 or thicker cables to connect the switch and the device.
4) Check the installation and the wiring, after confirming that the connection is correct and reliable,
power on the switch.
The installation is complete.
CAUTION
Power on the system only after confirming that the wiring is correct, to avoid damage to the
equipment.
connect For better transmission performance, it is recommended to use Cat5 or better cables to
the switch and powered devices.
to For better protection performance, it is recommended always make the ground connection first
and disconnect it at the end when operating the unit.
-Each PoE RJ 45 port can provide a maximum power of 30W for a powered device. Please do not
connect to a powered device with a power exceeding 30W.
id Before operating or maintaining the switch, please read the user manual carefully to avo
equipment damage caused by misoperation.
Specifications
Items UTP3- - GSW1604TS P200
Ethernet Ports
Downlink Ports 16*10/100/1000 Base- - - - T PoE RJ 45 (Auto MDI/MDI X)
Uplink Ports
2*10/100/1000 Base- - - -GBIC) T RJ 452*1000 Base X SFP(Mini
PoE
PoE Standard
IEEE 802.3af/at
PSE
PoE Power Supply Type
End- span
PoE Pin Assignment + - 1/2( ), 3/6( )
PoE Power Output
54V DC
PoE Power
30W max for each port, 175W max
Switch Property
Standards
IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3X
Forwarding Modes Store and Forward
Packet Buffer
4Mbyte
MAC Table
8k
Switching Capacity 40Gbps / non-blocking
Packet Forwarding Rate
28Mpps
Power Supply
Input Voltage 100V~240V AC, 50/60Hz
Power Consumption 200W (Including PoE)
Reliability
Surge Immunity 6kV, Standard: IEC6000-4-5
ESD 6 kV Contact Discharge, 8kV Air Discharge, standard: IEC61000-4-2
Operating Temperature
14F~122F (-10C to 50C)
Storage Temperature -40 85F~1 F (-40C to 85C)
Operating Humidity
5%~95% (Non-condensation)
Physical Parameters
Led Indicators
1*PWR Indicator
16*Downlink Port Link Indicators
16*Downlink Port PoE Indicators
4*Uplink Port Link Indicator
Dimension(W*D*H)
17.4” 11.2” 442mm*x x 1.7” ( 285 ) mm*44mm
Gross Weight
11 Lbs.(5000g)
Net Weight 8.4 Lbs. ( 3800g)
Material
Metal
Installation
Rack mounted/ wall mounted desktop/
Certifications
Certifications
CE, FCC
Speco Technologies is constantly developing and improving products. REV: 12/21/2020
We reserve the right to modify product design and specifications without notice and without incurring any obligation.
Speco Technologies . 200 New Highway . Amityville . NY . 11701 . www.specotech.com


Product specificaties

Merk: Speco Technologies
Categorie: Bewakingscamera
Model: P16S18G

Heb je hulp nodig?

Als je hulp nodig hebt met Speco Technologies P16S18G stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Bewakingscamera Speco Technologies

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera