Speco Technologies O4iB2M Handleiding

Speco Technologies Bewakingscamera O4iB2M

Lees hieronder de 📖 handleiding in het Nederlandse voor Speco Technologies O4iB2M (53 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/53

User Manual

4MP IP Camera

O4iB2/O4iB2M/O4iD2/ O4iD2M/ O4iT2/ O4iT2M

Please read this manual carefully before operang the unit keep it for further reference and

Important Safeguards and Warnings

1. Electrical safety

All installaon and operaon here should conform to local electrical safety codes.

Use a certied/listed 12VDC/24VAC (depending on models) Class2 or adequate PoE switch.

Improper handling and/or installaon could run the risk of re or electrical shock.

2. Environment

Do not expose the heavy stress, violent vibraon long-term exposure water humidity during transportaon, unit to or to and

storage, and/or installaon.

Do not install near sources heat. of

Only install the product environments inside the specicaon operang temperature humidity range. in and

Do not install the camera near power lines, radar equipment other electromagnec radiation. or

Do not block any venlaon openings any. if

Use all the weatherproong hardware requirement minimize weather intrusion.to

3. Operaon and Daily Maintenance

Please shut down the device and then unplug the power cable before you begin any maintenance work.

Do not touch the CMOS sensor opc component. You can use a blower to clean the dust on the lens surface.

Always use the dry so cloth to clean the device. If there is too much dust, use a cloth dampened with a small quanty of neutral

detergent. Finally use the dry cloth to clean the device.

Please use a professional opcal cleaning method to clean the enclosure.

The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.

Dome cover is an opcal device, please do not touch or wipe cover surface directly during installaon and use, please refer to the

following methods if dirt is found.

Stained with dirt:

Use oil-free so brush or hair dryer to remove it gently.

Stained with grease or ngerprint.

Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth and

wipe several mes if it is not clean enough.

Warning

This camera should be installed by qualied personnel only.

All the examinaon and repair work should be done by qualied personnel.

Any unauthorized changes or modicaons could void the warranty.

Statement

This guide is for reference only.

Product, manuals, and specicaons may be modied without prior noce. Speco Technologies reserves the right to modify these

without noce and without incurring any obligaon.

Speco Technologies is not liable for any loss caused by improper operaon.

Regulatory Informaon

FCC condions:

This device complies with part 15 of the FCC Rules. Operaon is subject to the following two conditions:

 This device may not cause harmful interference.

 This device must accept any interference received, including interference that may cause undesired operaon.

FCC compliance:

This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protecon against harmful interference. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instrucon manual, may cause harmful

interference to radio communicaon. However, there is no guarantee that interference will not occur in a parcular installaon. If

this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the

equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separaon between the equipment and receiver.

 Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

Note:

Before installaon, check the package and make sure that all components are included.

Contact your rep or Speco customer service department immediately if something is broken or missing in the package.

Accessory name

Amount

Network Camera Unit

Juncon box

Quick Start Guide

Installaon Accessories Bag

Product specificaties

Merk:	Speco Technologies
Categorie:	Bewakingscamera
Model:	O4iB2M

Heb je hulp nodig?

Als je hulp nodig hebt met Speco Technologies O4iB2M stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera Speco Technologies

Speco Technologies O2VLB7 Handleiding

27 Mei 2024

Speco Technologies VLDT3GM Handleiding

6 Juli 2023

Speco Technologies CVC624WDR Handleiding

1 Juli 2023

Speco Technologies O4iB2M Handleiding

30 Juni 2023

Speco Technologies ZIPTW4B1 Handleiding

27 Juni 2023

Speco Technologies O2ID21M Handleiding

26 Juni 2023

Speco Technologies Intensifier 2 CVC6246iHR Handleiding

26 Juni 2023

Speco Technologies O4DT1 Handleiding

25 Juni 2023

Speco Technologies O4iB2 Handleiding

25 Juni 2023

Speco Technologies O8D8M Handleiding

22 Juni 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Honeywell HC35WE5R3 Handleiding

20 December 2024

Honeywell Performance H4W8PER2V Handleiding

20 December 2024

Hikvision DS-2CE12KF3T-LS Handleiding

18 December 2024

Hikvision DS-2CE78D0T-LXTS/A Handleiding

18 December 2024

TP Link VIGI C450 Handleiding

18 December 2024

Hikvision DS-2CE76U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE78U0T-LF Handleiding

18 December 2024

Hikvision DS-2CE16U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE72KF3T-LSYE Handleiding

18 December 2024

Hikvision DS-2CE17U0T-LF Handleiding

18 December 2024