Speco Technologies O4VB1 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Speco Technologies O4VB1 (63 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/63
User Manual
4MP IP Camera
O4 /OVB1 4VB1M VT1 T1M/O4VD1/O4 /O4V
Please read this instruction carefully before operating the unit and keep it for further reference
Important Safeguards and Warnings
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time; it may result in device damage!
The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage and installation.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened with a small quantity of
neutral detergent. Finally use the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth)
may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
Dome cover is an optical device, please don t touch or wipe cover surface directly during installation and use, please refer ’
to the following methods if dirt is found.
Stained with dirt:
Use oil free soft brush or hair dryer to remove it gently.-
Stained with grease or fingerprint
Use oil free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth -
and wipe several times if it is not clean enough.
Warning
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
Statement
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco Technologies reserves the right to modify
these without notice and without incurring any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Regulatory Information
FCC conditions:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
 This device may not cause harmful interference.
 This device must accept any interference received, including interference that may cause undesired operation.
FCC compliance:
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or missing in the package.
Accessory name Amount
Network Camera Unit 1
Junction Box 1
Quick Start Guide 1
Installation Accessories Bag 1
CD 1


Product specificaties

Merk: Speco Technologies
Categorie: Bewakingscamera
Model: O4VB1

Heb je hulp nodig?

Als je hulp nodig hebt met Speco Technologies O4VB1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Bewakingscamera Speco Technologies

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera