Speco Technologies O4P25X2 Handleiding

Speco Technologies Bewakingscamera O4P25X2

Lees hieronder de 📖 handleiding in het Nederlandse voor Speco Technologies O4P25X2 (65 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/65
User Manual
PTZ Network Camera
O4P25X2
Please read this instruction carefully before operang the unit keep it for further reference and
1. Electrical safety
All installaon and operaon here should conform to local electrical safety codes.
Use a certied/listed 24VDC/AC (depending on models) Class2 or adequate PoE switch.
Improper handling and/or installaon could run the risk of re or electrical shock.
2. Environment
Do not expose the heavy stress, violent vibraon long-term exposure water humidity during transportaon, unit to or to and
storage, and/or installaon.
Do not install near rces heat. sou of
Only install the product environments inside the specicaon operating temperature in and humidity range.
Do not install the camera near power lines, radar equipment other electromagnec radiaon. or
Do not block any venlaon openings any. if
Use all the weatherproong hardware requirement minimize weather intrusion.to
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface.
Always use the dry so cloth to clean the device. If there is too much dust, use a cloth dampened with a small quanty of neutral
detergent. Finally use the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth) may
result in poor IR funconality and/or IR reecon.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
Dome cover is an opcal device, please do not touch or wipe cover surface directly during installaon and use, please refer to the
following methods if dirt is found.
Stained with dirt:
Use oil-free so brush or hair dryer to remove it gently.
Stained with grease or ngerprint.
Use oil-free coon cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth and
wipe several mes if it is not clean enough.
Warning
This camera should be installed by qualied personnel only.
All the examination and repair work should be done by qualied personnel.
Any unauthorized changes or modicaons could void the warranty.
Statement
This guide is for reference only.
Product, manuals, and specicaons may be modied without prior noce. Speco Technologies reserves the right to modify these
without noce and without incurring any obligaon.
Speco Technologies is not liable for any loss caused by improper operation.
Regulatory Informaon
FCC condions:
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operaon.
FCC compliance:
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protecon against harmful interference. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instrucon manual, may cause harmful
interference to radio communicaon. However, there is no guarantee that interference will not occur in a parcular installaon. If
this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separaon between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Note:
Before installaon, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or missing in the package.

Product specificaties

Merk: Speco Technologies
Categorie: Bewakingscamera
Model: O4P25X2

Heb je hulp nodig?

Als je hulp nodig hebt met Speco Technologies O4P25X2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Bewakingscamera Speco Technologies

Speco Technologies

Speco Technologies O2VLB7 Handleiding

27 Mei 2024
Speco Technologies

Speco Technologies VLDT3GM Handleiding

6 Juli 2023
Speco Technologies

Speco Technologies CVC624WDR Handleiding

1 Juli 2023
Speco Technologies

Speco Technologies O4iB2M Handleiding

30 Juni 2023
Speco Technologies

Speco Technologies ZIPTW4B1 Handleiding

27 Juni 2023
Speco Technologies

Speco Technologies O2ID21M Handleiding

26 Juni 2023
Speco Technologies

Speco Technologies Intensifier 2 CVC6246iHR Handleiding

26 Juni 2023
Speco Technologies

Speco Technologies O4DT1 Handleiding

25 Juni 2023
Speco Technologies

Speco Technologies O4iB2 Handleiding

25 Juni 2023
Speco Technologies

Speco Technologies O8D8M Handleiding

22 Juni 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Provision ISR

Provision ISR I3-350IP5SMVF Handleiding

20 November 2024
Provision ISR

Provision ISR I2-350A-28 Handleiding

20 November 2024
Provision ISR

Provision ISR I4-350A-MVF Handleiding

20 November 2024
Canon

Canon PowerShot GOLF Handleiding

20 November 2024
Flir

Flir FH-Series Handleiding

20 November 2024
EtiamPro

EtiamPro CCTVPROM23 Handleiding

17 November 2024
EtiamPro

EtiamPro CCTVPROM20W Handleiding

17 November 2024
Leviton

Leviton 68A02-2 Handleiding

17 November 2024
Reolink

Reolink RLK8-800D4 Handleiding

16 November 2024
Reolink

Reolink RLK16-800D8 Handleiding

16 November 2024