Sony SNC-ZR550 Handleiding

Sony Bewakingscamera SNC-ZR550

Lees hieronder de 📖 handleiding in het Nederlandse voor Sony SNC-ZR550 (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

4-282-057- (1)13

Network Camera

Installation Manual

Before operating the unit, please read this manual thoroughly and

retain it for future reference.

SNC-EP580/ER580/EP550/ER550

SNC-EP520/ER520/EP521/ER521

SNC-ZP550/ZR550

Owner’s Record

The model and serial numbers are located on the bottom. Record these

numbers in the spaces provided below.

Refer to these numbers whenever you call upon your Sony dealer regarding

this product.

Model No. Serial No.

Overview

This Installation Manual gives instructions for multiple types of Network

Cameras: SNC-EP520/EP521/ER520/ER521 are SD models, SNC-EP550/ER550

are HD models, SNC-EP580/ER580 are Full HD models, and SNC-ZP550/ZR550

are HD model IPELA HYBRID-compatible cameras.

WARNING

To reduce the risk of fire or electric shock, do not expose

this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer

servicing to qualified personnel only.

CAUTION

This installation should be made by a qualified service person and should

conform to all local codes.

WARNING

A readily accessible disconnect device shall be incorporated in the building

installation wiring.

WARNING (for Installers only)

Instructions for installing the equipment on the ceiling:

After the installation, ensure the connection is capable of supporting five

times the weight of the equipment downwards.

CAUTION

The rating label is located on the bottom.

CAUTION for LAN port

For safety reason, do not connect the LAN port to any network devices that

might have excessive voltage.

The LAN port of this unit is to be connected only to the devices whose

power feeding meets the requirements for SELV (Safety Extra Low Voltage)

and complies with Limited Power Source according to IEC 60950-1.

Power Supply

The SNC-EP580/EP550/EP521/EP520/ER580/ER550/ER521/ER520 operates

on 24 V AC.

Caution for U.S.A. and Canada

Use a Class 2 power supply which is UL Listed (in the U.S.A.) or CSA-certified

(in Canada).

Caution for other countries

Use a power supply rated 24 V AC which meets the requirements for

SELV (Safety Extra Low Voltage) and complies with Limited Power Source

according to IEC 60950-1.

Use IEEE802.3at standard compliant devices.

For the customers in the U.S.A.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved

in this manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order to

comply with the limits for a digital device pursuant to Subpart B of Part 15 of

FCC Rules.

For the customers in Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du

Canada.

For the customers in Europe

The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-

ku, Tokyo, Japan.

The Authorized Representative for EMC and product safety is Sony

Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.

For the customers in Europe, Australia and New Zealand

WARNING

This is a Class A product. In a domestic environment, this product may cause

radio interference in which case the user may be required to take adequate

measures.

In the case that interference should occur, consult your nearest authorized

Sony service facility.

This apparatus shall not be used in the residential area.

ATTENTION

The electromagnetic fields at the specific frequencies may influence the

picture of this unit.

Notes on Use

Before Use

If you find condensation when you open the package, turn on the power after

the condensation disappears.

Data and security

Since the service is Internet-based, there is a risk that the image or audio you

are monitoring can be viewed or used by a third-party via the network. You

should keep in mind that the images or audio you are monitoring may be

protected by privacy and other legal rights, and the responsibility for making

sure you are complying with applicable laws is yours alone.

Access to the images and audio is protected only by a user name and the

password you set up. No further authentication is provided nor should you

presume that any other protective filtering is done by the service.

SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU

OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR

EVEN SERVICE CANCELLATION. THE SERVICE IS PROVIDED AS-IS, AND SONY

DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH

RESPECT TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.

Always make a test recording, and verify that it was recorded successfully.

SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT

LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE

OF THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR

ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE.

Always verify that the unit is operating properly before use. SONY WILL NOT

BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,

COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT

OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE

WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY

OTHER REASON WHATSOEVER.

If you lose data by using this unit, SONY accepts no responsibility for

restoration of the data.

Personal information

The images taken by the system using this device can identify individuals

and thus they fall under “personal information” stipulated in the “Act on the

Protection of Personal Information”. Please handle the video data appropriately

according to law.

Information recorded using this product may also be “personal information”.

Upon disposal, transfer, repair, or any other occasion where this product or

storage media is passed on to a third party, practice due care in its handling.

Operating or storage location

Avoid operating or storing the camera in the following locations.

Extremely hot or cold places

Exposed to direct sunlight for a long time, or close to heating equipment

(e.g., near heaters)

Close to sources of strong magnetism

Close to sources of powerful electromagnetic radiation, such as radios or TV

transmitters

Locations subject to vibration or shock

Humid or dusty locations

Locations exposed to rain

Ventilation

To prevent heat buildup, do not block air circulation around the camera.

Power supply

The power is supplied via a network cable, when the camera operates using

HPoE (High-Power-over-Ethernet).

Use STP/UTP Category 5 network cable.

Using a damaged network cable may cause a risk of fire or electric shock.

Transportation

Always turn off the power when carrying.

When transporting the camera, repack it as originally packed at the factory or

in materials of equal quality.

Cleaning

Use a blower to remove dust from the lens.

Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn

stains can be removed using a soft cloth dampened with a small quantity of

detergent solution, then wipe dry.

Do not use volatile solvents such as alcohol, benzene or thinners as they may

damage the surface finishes.

Please consult the store of purchase or authorized Sony dealer if there were

troubles and anomalies.

Note on laser beams

Laser beams may damage image sensors. You are cautioned that the surface of

image sensors should not be exposed to laser beam radiation in an environment

where a laser beam device is used.

SD card

Data written in the SD card may be damaged or erased in the following cases:

The SD card is taken out of this unit, or this unit is turned off while the SD card

is being accessed.

The SD card has reached the end of its service life.

The SD card has become damaged by dropping, etc.

The SD card is not installed in this unit properly.

Sony is not responsible for damages or lost profit caused by lost data.

Camera settings

DynaView(WDR) is not available when the slow shutter is used.

The exposure compensation function is not available when DynaView(WDR) is

used.

Phenomena Specific to Image Sensors

The following phenomena that may occur in images are specific to image

sensors. They do not indicate a malfunction.

White flecks

Although the image sensors are produced with high-precision technologies, fine

white flecks may be generated on the screen in rare cases, caused by cosmic rays, etc.

This is related to the principle of image sensors and is not a malfunction.

The white flecks especially tend to be seen in the following cases:

- when operating at a high environmental temperature

- when you have raised the gain (sensitivity)

- when using the slow shutter

Vertical smear (SNC-EP521/EP520/ER521/ER520)

When an extremely bright object, such as a strong spotlight or flashlight, is being

shot, vertical tails may be produced on the screen, or the image may be distorted.

Aliasing

When fine patterns, stripes, or lines are shot, they may appear jagged or flicker.

About the Supplied Manuals

Installation Manual (this document)

This Installation Manual describes the names and functions of parts and controls

of the Network Camera, gives connection examples and explains how to set up

the camera. Be sure to read the Installation Manual before operating.



User’s Guide (stored in the CD-ROM)

The User’s Guide describes how to set up the camera and how to control the

camera via a Web browser.

After installing and connecting the camera correctly, operate referring to this

User’s Guide.

Using the CD-ROM Manuals

The supplied CD-ROM disc includes the User’s Guides for this unit (Japanese,

English, French, German, Spanish, Italian and Chinese versions) in PDF format.

Preparations

Adobe Reader Version 6.0 or higher must be installed on your computer in order

to use the User’s Guide stored in the CD-ROM disc.

If Adobe Reader is not installed, it may be downloaded from the following URL:

http://www.adobe.com/

Reading the manual in the CD-ROM

1 Insert the CD-ROM in your CD-ROM drive.

A cover page appears automatically in your Web browser.

If it does not appear automatically in the Web browser, double-click on the

index.htm file on the CD-ROM.

2 Select and click on the manual that you want to read.

This opens the PDF file of the manual.

Clicking an item in the Table of Contents allows you to jump to the relevant

page.

Notes

The files may not be displayed properly, depending on the version of Adobe

Reader. In this case, install the latest version, which you can download from

the URL mentioned in “Preparations” above.

If you have lost or damaged the CD-ROM, you can purchase replacement.

Contact your Sony service representative.

Smartphone viewer

This product is equipped with a Smartphone viewer.

With Smartphone viewer, you can display an image from a network camera, pan,

tilt and zoom that camera, on your smartphone.

For more details, see “Smartphone viewer User’s Manual” at the following URL:

http://www.sony.net/ipela/snc

Location and Function of Part 

 Lens

 Camera head

  LAN (network) port (RJ-45)

Connect to a 10BASE-T or 100BASE-TX network using a network cable (UTP,

category 5).

When using an HPoE system to operate the camera, connect a power feeding

device to this port. The PoE power supply feature is not available on SNC-

ZP550/ZR550 when the network connection change switch is set to SLOC. For

details, refer to the instructions manual of the power feeding device.

* HPoE: High-Power-over-Ethernet, IEEE802.3at compliant.

 Product specifications label

Model names and rated specifications are labeled.

 SD memory card slot

This slot is used for an optional SD memory card.

Images captured by the camera can be stored into an inserted memory card.

Be sure that the printed side of a memory card and the product specifications

label face in the same direction, and then insert the card firmly into the slot.

( )

This unit only supports memory card formats compatible with the SD/SDHC

standards.

Note

For information about Sony-approved SD memory cards, contact your

authorized Sony dealer.

  (microphone input) terminal (minijack, monaural)

Connect a commercially available microphone.

  (line output) terminal (minijack, monaural)

Connect to a commercially available speaker with a built-in amplifier.

 Built-in wire rope

The wire rope is used for fall-prevention of the camera.

 Network connection change switch (SNC-ZP550/ZR550)

Use this switch to change between a network connection to a LAN (network)

port (RJ-45) and a network connection using a coaxial cable.

 SLOC (IP coaxial transfer/video output) port (SNC-ZP550/ZR550)

Use this port when connecting the unit to a network using a coaxial cable.

Also use this port to output composite video signals from this unit. When

outputting a composite signal, set the network connection change switch to

LAN.

A connection to compatible equipment is necessary when connecting to a

network using a coaxial cable.

For connection details, refer to the instruction manuals of the equipment on

the receiving end.

Note

The output analog image may not display correctly, depending on the

video format and image size settings.

The image may not display properly in the horizontal and/or vertical plane.

The image may be reduced.



 AC 24 V (power input) terminal

Use the provided AC power cable to connect to the 24 V AC power supply

system.

 NETWORK indicator (green/orange)

The indicator lights up or flashes when the camera is connected to the

network. The indicator is off when the camera is not connected to the

network.

When 100BASE-TX is connected, the indicator turns green. When 10BASE-T is

connected, the indicator turns orange.

The indicator also turns green when SLOC (IP coaxial transfer) is selected.

(SNC-ZP550/ZR550)

 POWER indicator (green)

When the camera receives power, a system check is run internally in the

camera. The indicator lights up when the camera is operating normally.

 I/O (Input/Output) port

Provides two sensor inputs and one alarm outputs.

Pin No. Pin name

1 Alarm In 2

2 GND

3 Alarm In 1

4 GND

5 Alarm Out+

6 Alarm Out–

Note

For details about functions and settings, see the user’s guide in the supplied

CD-ROM.



 2011 Sony Corporation Printed in Japan

 

Product specifications label

Printed side (of SD memory card)

Push down the perforated

tab when bundling the cables

from the side of the camera.

 BNC cable (attached, factory-connected) (SNC-ZP550/ZR550)

Outputs SLOC (IP coaxial transfer) signals and video signals.

 Reset switch

The camera can also be reset to the factory setting by turning on the

power while pressing the reset switch with a needle/paper clip.

 Cable cover

Push down the perforated tab to bundle the cables from the side of 

the camera.

(continued on the reverse side)

Installation

Notes

Do not grasp the camera head when carrying the camera.

Do not turn the camera head manually. Doing so will likely result in the

camera malfunctioning.

Turn off the power of the camera before installing it.

Install the camera to a horizontal place. If you have to install the camera to an

incline, make sure the incline is within ±15° to the horizontal level to ensure the

turning performance of the camera.

Installing the Camera on a Ceiling 

Use the supplied ceiling bracket to install the camera.

The ceiling bracket is attached to the camera unit. Remove it before installing.

WARNING

If you attach the camera in a high location such as wall or ceiling, etc., entrust

the installation to an experienced contractor or installer.

If you install the camera in a high location, ensure that the ceiling is strong

enough to withstand the weight of the camera plus mounting brackets

and screws, and then install the camera securely. If the ceiling is not strong

enough, the camera may fall and cause serious injury.

To prevent the camera from falling, make sure to attach the built-in wire rope.

If you attach the camera to the ceiling, check periodically, at least once a year,

to ensure that the connection has not loosened. If conditions warrant, make

this periodic check more frequently.

Before installation

Decide the direction in which the camera will shoot, before making holes for

wiring and screw holes.

Push down the perforated tab to bundle the cables from the side of the

camera. (For details, see “ Cable cover” in “Location and Function of Part.”)

Installing directly on a ceiling

Using the supplied template, make a hole for the wiring (ø40 mm (1 5/8 inches)).

Determine the location of the three screw holes for attaching the ceiling bracket.

( )

Using the existing junction box

Attach the ceiling bracket to the junction box. Screws for this operation are not

supplied.

Attach the ceiling bracket in a manner that the triangular mark faces the front

side of the camera.

Fixing screws

Required screws (not supplied) vary in accordance with the location or material

of the installation.

For steel: Fix with M4 screws and nuts.

For wood: Fix with tapping screws (nominal diameter 4). A material thickness of

15 mm (19/32 inches) or more is necessary.

For a concrete wall: Fix with dry bit or plug bolts.

For a junction box: Fix with screws that accommodate the screw holes in the

junction box.

WARNING

Use the appropriate screws in accordance with the condition and material of the

location site. Otherwise, the ceiling unit may fall and cause serious injury.

How to install

1 Put the built-in wire rope on the hook in the ceiling bracket. ( -1)

2 Connect the cables.

Note

Although you can connect the cables while the camera unit is hanging from

the ceiling bracket with the help of the rope, be sure not to put additional

pressure on the unit.

3 Align the triangular mark on the camera with the diamond-shaped

mark on the ceiling bracket, and then attach the camera unit into the

bracket. ( -2)

4 Rotate the camera unit in a clockwise direction.

5 Attach the camera unit to the ceiling bracket by fixing two screws at both

sides of the unit.

6 Attach the cable cover.

Note

Use the supplied screws to install the unit. Using other screws may cause

damage inside the unit.



Video S/N 50 dB (Gain 0 dB)

Lens

Focus length SNC-EP580/ER580: f=4.7 to 94.0 mm

SNC-EP550/ER550/ZP550/ZR550: f=3.5 to 98.0

SNC-EP521/EP520/ER521/ER520: f=3.4 to 122.4

Maximum relative aperture SNC-EP580/ER580: F1.6 to F3.5

SNC-EP550/ER550/ZP550/ZR550: F1.35 to F3.7

SNC-EP521/EP520/ER521/ER520: F1.6 to F4.5

Minimum object distance 320 mm

Mechanism

Pan SNC-EP580/EP550/EP521/EP520/ZP550: 340°

SNC-ER580/ER550/ER521/ER520/ZR550: 360°,

endless rotation

Maximum speed: 300°/s

Tilt SNC-EP580/EP550/EP521/EP520/ZP550: 105°

SNC-ER580/ER550/ER521/ER520/ZR550: 210°

(with auto invert function)

Maximum speed: 300°/s

Interface

Network port 10BASE-T/100BASE-TX, auto negotiation (RJ-45)

I/O port Sensor input: × 2, make contact

Alarm output: × 1, 24 V AC/DC, 1 A

(mechanical relay outputs electrically isolated

from the camera)

SD memory card slot

Microphone input Minijack (monaural)

Plug-in-power supported (rated voltage: 2.5 V DC)

Recommended load impedance 2.2 kohms

Line output Minijack (monaural), Maximum output level:

1 Vrms

SLOC port/Monitor output (SNC-ZP550/ZR550)

1.0 Vp-p, 75 ohms, unbalanced, sync negative

(during video output)

Others

Power supply 24 V AC ± 10%, 50 Hz/60 Hz

IEEE802.3at compliant (HPoE system)

Power consumption Max. 25 W

Operating temperature –5°C to +50°C (23°F to 122°F) (activation

temperature range: 0°C to 50°C (32°F to 122°F))

Storage temperature –20°C to +60°C (–4°F to +140°F)

Operating humidity 20% to 80%

Storage humidity 20% to 95%

Dimensions (Diameter/Height) 

ø147.4 mm × 190.9 mm (ø5 7/8 inches ×

7 5/8 inches) (When installing the ceiling bracket,

not including the projecting parts)

Mass Approx. 1.7 kg (3 lb 12 oz) (including ceiling

bracket)

Supplied accessories Ceiling bracket (1)

Screws (2)

Installation manual (1 set)

CD-ROM (User’s Guide, supplied programs) (1)

Template (1)

24 V AC connector (1)

I/O connector (1)

Design and specifications are subject to change without notice.

Recommendation of Periodic Inspections

In case using this device over an extended period of time, please have it

inspected periodically for safe use.

It may appear flawless, but the components may have deteriorated over

time, which may cause a malfunction or accident.

For details, please consult the store of purchase or an authorized Sony dealer.

Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in

the United States and/or other countries.

sloc™ is a trademark owned by the Intersil Corporation family of companies.







How to install

Celing bracket

Camera (When installing the ceiling bracket)

Screw (supplied)

Align the triangular

mark on the camera

with the diamond-

shaped mark on the

ceiling bracket.

Ceiling bracket

Align the triangular

mark with the

front side of the

camera when using

a junction box.

Built-in wire rope

Ceiling

Hook

3-Screw hole

ø130 (5 1/8)

Unit: mm (inches)

ø40 (1 5/

Cable hole

120°

85.7 (3 3/8)

83.5 (3 9/32)Hole 13-ø4.5 (3/16)

ø130 (5

)

120°

83.5 (3

)

83.5 (3 9/32)

85.7 (3 3/8)

45°

190.9 (7 5/8) (When installing the bracket)

190 (7 1/2) (Camera unit only)

ø147.4 (5 7/8)

132 (5 1/4)

(When installing the bracket)

Unit: mm (inches)

LAN I/O cable24 V AC Coaxial

cable

Mic

Input

10BASE-T/

100BASE-TX

Hub

Network

Install a hub compatible

with HPoE when using

an HPoE system.

Network cable

(straight, not supplied)

Audio

Output

Ceiling bracket

Ceiling

Unit: mm (inches)

How to remove the camera

1 Loosen and remove the two screws on both sides of the camera unit.

2 Rotate the camera unit in a counterclockwise direction, and remove it

from the ceiling bracket.

3 Disconnect the cables.

Note

Although you can disconnect the cables while the camera unit is hanging

from the ceiling bracket with the help of the rope, be sure not to put

additional pressure on the unit.

4 Unhook the built-in wire rope from the ceiling bracket, and dismount the

camera unit.

Note

Always hold the camera when you dismount the camera unit. This will

prevent any risk of the camera falling.

Install the camera with its head facing upward

Follow the same steps as in “Installing the Camera on a Ceiling” when installing or

removing the camera.

Be sure to place the camera securely to prevent it from falling.

Note

By default, the images from the camera are displayed normally when the camera

is installed on the ceiling. To display the images from the camera in correct way

when you place the camera on the desk top, use the E.flip function.

 For the setting of the E.flip function, see the User’s Guide stored in the

supplied CD-ROM.

Connection

Connecting to the Network 

Connect the LAN port of the camera unit to a router or hub in the network using

the network cable (straight, not supplied).

To connect to a computer

Connect the LAN port of the camera unit to the network connector of a

computer using the network cable (cross, not supplied).

To connect to a network using a coaxial cable

(SNC-ZP550/ZR550) 

When the network connection change switch is set to SLOC, connect to a

network via a coaxial cable.

The maximum coaxial cable length is 3C-2V 300 m.

Note

The high-frequency characteristics of coaxial cables may differ, even if the

cables are of the same classification. Use a high-quality, high-frequency

coaxial cable with this unit.

 For details, refer to the instruction manual of the connecting SLOC device.

For further details, please consult an authorized Sony dealer.

Connecting the Power Source 

The following two methods are available for connecting to a power source.

24 V AC

HPoE

Note

If you use this camera by feeding power to the LAN port, use the HPoE power

feeding device.

Connecting to a 24 V AC power source supply

Connect the 24 V AC power supply system to the power input terminal of the

camera.

Use a 24 V AC power source isolated commercial power supply.

The usable voltage range is as follows:

24 V AC: 21.6 to 26.4 V

Use a UL cable (VW-1 style 10368) for 24 V AC connection.

Recommended power cable

24 V AC

Cable(AWG) #24 #22 #20

Maximum cable

length (m (feet)) 11 (36.1) 19 (62.3) 28 (91.9)

Connecting to the power supply equipment pursuant to

IEEE802.3at

The power supply equipment pursuant to IEEE802.3at supplies the power

through the LAN cable. For details, refer to the Instruction Manual of the

equipment.

Connecting the I/O Cable

Wiring diagram for sensor input

Mechanical switch/open collector output device

Camera inside

3.3 V

10 kohms

GND

Mechanical

switch

Open collector

output device

Outside

2.2 kohms

10 kohms

GNDGND

10 kohms

3 or 1 pin

(Alarm Input 1 or 2)

2 or 4 pin

GND

Wiring diagram for alarm output

Camera inside

5 pin

(Alarm Output +)

Magnet relay

24 V AC

24 V DC,

1 A or less

6 pin

(Alarm Output –)

Outside

24 V DC

Circuit example

GND

Specifications

Compression

Video compression format JPEG/MPEG4/H.264

Audio compression format G.711/G.726 (40,32,24,16 kbps)

Maximum frame rate 30 fps

Camera

Image device SNC-EP580/ER580: 1/2.8 type Exmor CMOS

SNC-EP550/ER550/ZP550/ZR550: 1/4 type Exmor

CMOS

SNC-EP521/EP520/ER521/ER520: 1/4 type

interline transfer CCD

Synchronising Internal

Minimum illumination SNC-EP580/ER580: 1.7 lx (Shutter speed: 1/30 sec,

Exposure: Full auto, 50IRE [IP])

SNC-EP550/ER550/ZP550/ZR550: 1.0 lx (Shutter

speed: 1/60 sec, Exposure: Full auto, 50IRE [IP])

SNC- EP521/ER521: 1.4 lx (Shutter speed: 1/50 sec,

Exposure: Full auto, 50IRE [IP])

SNC- EP520/ER520: 1.4 lx (Shutter speed: 1/60 sec,

Exposure: Full auto, 50IRE [IP])



memory

card

Coaxial cable maximum

length: 3C-2V 300 meters

SLOC connector

SLOC-compatible

device

Video output terminal LAN port (RJ-45)

Coaxial cable

Network cable

10BASE-T/

100BASE-TX

Video monitor (etc.) Network device

Product specificaties

Merk:	Sony
Categorie:	Bewakingscamera
Model:	SNC-ZR550
Kleur van het product:	Black, White
Gewicht:	1700 g
Hoogte:	190.9 mm
Soort:	IP-beveiligingscamera
Gebruiksaanwijzing:	Ja
Montage gereedschap:	Ja
Ondersteunde videoformaten:	H.264, M-JPEG, MPEG4
Vormfactor:	Dome
Ondersteuning voor plaatsing:	Binnen & buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Montagewijze:	Plafond
Ondersteunde video-modi:	720p
Maximum resolutie:	1280 x 720 Pixels
Totaal aantal megapixels:	1.43 MP
Diameter:	147.4 mm
Type stroombron:	Power over Ethernet (PoE)
Minimale belichting:	1 Lux
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	SD, SDHC
Ingebouwde HDD:	Nee
Microfoon, line-in ingang:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	1
Brandpuntbereik:	3.5 - 98 mm
Formaat analoog signaal:	NTSC, PAL
Omvang optische sensor:	1/4 "
Aansluiting voor netstroomadapter:	Ja
Type beeldsensor:	CMOS
Digitale zoom:	12 x
Optische zoom:	28 x
Camera sluitertijd:	1/1 s
Interface:	BNC
Ondersteunde grafische resoluties:	320 x 192,320 x 240,384 x 288,640 x 368,704 x 576,720 x 480,720 x 576,768 x 576,1024 x 576 (WSVGA),1280 x 720 (HD 720),640 x 480 (VGA),800 x 480 (WVGA),800 x 600 (SVGA)
Bekabelingstechnologie:	10/100Base-T(X)
Ondersteunt Windows:	Ja
Temperatuur bij opslag:	-20 - 60 °C
Maximaal 30 frames per seconde:	30 fps
Luchtvochtigheid bij opslag:	20 - 95 procent
Power over Ethernet (PoE):	Ja
PTZ control:	Ja
Minimale processor:	Core 2 Duo 2GHz
Pan bereik:	0 - 360 °
Dag/nacht modus:	Ja
Draai-snelheid:	300 °/sec
Pan snelheid:	300 °/sec
Montagebeugels meegeleverd:	Ja
Minimale RAM:	1024 MB
Alarm ingang/uitgang:	Ja
Wifi:	Nee
AC-ingangsspanning:	24 V
Stroomverbruik (typisch):	25 W
Bedrijfstemperatuur (T-T):	-5 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 80 procent
Bereik kantelhoek:	0 - 210 °
Kijkhoek lens, horizontaal:	55.9 °