Sony SNC-RX530P Handleiding

Sony Bewakingscamera SNC-RX530P

Lees hieronder de 📖 handleiding in het Nederlandse voor Sony SNC-RX530P (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

3-286-973- (1)12

Network Camera

Installation Manual

Before operating the unit, please read this manual thoroughly and

retain it for future reference.

SNC-RX570N/RX570P

SNC-RX550N/RX550P

SNC-RX530N/RX530P

Owner’s Record

The model and serial numbers are located on the bottom. Record these

numbers in the spaces provided below.

Refer to these numbers whenever you call upon your Sony dealer regarding

this product.

Model No. Serial No.

WARNING

To reduce a risk of re or electric shock, do not expose

this product to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer

servicing to qualied personnel only.

WARNING

This installation should be made by a qualied service person and should

conform to all local codes.

WARNING

A readily accessible disconnect device shall be incorporated in the building

installation wiring.

WARNING (for Installers only)

Instructions for installing the equipment on the ceiling:

After the installation, ensure the connection is capable of supporting ve

times the weight of the equipment downwards.

CAUTION

The rating label is located on the bottom.

CAUTION for LAN port

For safety reason, do not connect the LAN port to any network devices that

might have excessive voltage.

Power Supply

Caution for U.S.A. and Canada

The SNC-RX570N/RX550N/RX530N operates on 24V AC or 12V DC.

The SNC-RX570N/RX550N/RX530N automatically detects the power.

Use a Class 2 power supply which is UL Listed (in the U.S.A.) or CSA-certied

(in Canada).

Caution for other countries

The SNC-RX570N/RX570P/RX550N/RX550P/RX530N/RX530P operates on

24V AC or 12V DC.

The SNC-RX570N/RX570P/RX550N/RX550P/RX530N/RX530P automatically

detects the power.

Use a power supply rated 24 V AC or 12 V DC which meets the requirements

for SELV (Safety Extra Low Voltage) and complies with Limited Power Source

according to IEC 60950.

For customers in the U.S.A. (SNC-RX570N/RX550N/RX530N only)

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

You are cautioned that any changes or modications not expressly approved

in this manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order to

comply with the limits for a digital device pursuant to Subpart B or Part 15 of

FCC Rules.

For customers in Canada (SNC-RX570N/RX550N/RX530N only)

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du

Canada.

For the customers in Europe

The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-

ku, Tokyo, Japan.

The Authorized Representative for EMC and product safety is Sony

Deutschland GmbH, Hedelnger Strasse 61, 70327 Stuttgart, Germany.

For any service or guarantee matters please refer to the addresses given in

separate service or guarantee documents.

For the customers in Europe, Australia and New Zealand

WARNING

This is a Class A product. In a domestic environment, this product may cause

radio interference in which case the user may be required to take adequate

measures.

In the case that interference should occur, consult your nearest authorized

Sony service facility.

This apparatus shall not be used in the residential area.

ATTENTION

The electromagnetic elds at specic frequencies may inuence the picture

of the unit.

For the customers in Taiwan only

Features

Monitoring of a high-quality live image from the camera is possible. The

maximum frame rate is 30 fps for SNC-RX570N/RX550N/RX530N and 25 fps for

SNC-RX570P/RX550P/RX530P.

Three video compression modes (video codecs) JPEG/MPEG4/H.264 are

supported.

Single codec mode and Dual codec mode are switchable.

A high-speed (300° rotation/second) pan/tilt mechanism is equipped. This

allows 360° endless panning and -90° to 0° tilting.

Optical zoom of 36 magnications (SNC-RX570N/P), 26 magnications (SNC-

RX550N/P) or 18 magnications (SNC-RX530N/P), and digital zoom of 12

magnications are provided.

Inserting the optional wireless card enables wireless transmission of camera

images.

Up to 16 preset positions and 5 tour programs can be saved.

Intelligent object detection function is provided.

Up to 20 users can view an image from the camera at the same time.

Date/time can be superimposed on the image.

Notes on Use

Data and security

You should keep in mind that the images or audio you are monitoring may be

protected by privacy and other legal rights, and the responsibility for making

sure you are complying with applicable laws is yours alone.

Access to the images and audio is protected only by a user name and the

password you set up. No further authentication is provided nor should you

presume that any other protective ltering is done by the service. Since

the service is Internet-based, there is a risk that the image or audio you are

monitoring can be viewed or used by a third-party via the network.

SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU

OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR

EVEN SERVICE CANCELLATION. THE SERVICE IS PROVIDED AS-IS, AND SONY

DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH

RESPECT TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.

Security conguration is essential for wireless LAN. Should a problem

occur without setting security, or due to the limitation of the wireless LAN

specications, SONY shall not be liable for any damage.

Always make a test recording, and verify that it was recorded successfully.

SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT

LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE

OF THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR

ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE.

Always verify that the unit is operating properly before use. SONY WILL NOT

BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,

COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT

OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE

WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY

OTHER REASON WHATSOEVER.

If you lose data by using this unit, SONY accepts no responsibility for

restoration of the data.

Operating or storage location

Do not shoot an extremely bright object (an illumination, the sun, etc.). Also,

avoid operating or storing the camera in the following locations, as these can be

a cause of a malfunction.

Extremely hot or cold places (Operating temperature: 0 °C to +50 °C [32 °F to

122 °F])

Exposed to direct sunlight for a long time, or close to heating equipment (e.g.,

near heaters)

Close to sources of strong magnetism

Close to sources of powerful electromagnetic radiation, such as radios or TV

transmitters

Locations subject to strong vibration or shock

Ventilation

To prevent heat buildup, do not block air circulation around the camera.

Transportation

When transporting the camera, repack it as originally packed at the factory or in

materials of equal quality.

Cleaning

Use a blower to remove dust from the lens.

Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn

stains can be removed using a soft cloth dampened with a small quantity of

detergent solution, then wipe dry.

Do not use volatile solvents such as alcohol, benzene or thinners as they may

damage the surface nishes.

Note on laser beams

Laser beams may damage a CCD. You are cautioned that the surface of a CCD

should not be exposed to laser beam radiation in an environment where a laser

beam device is used.

Phenomena Specic to CCD Image Sensors

The following phenomena that may appear in images are specic to CCD (Charge

Coupled Device) image sensors. They do not indicate malfunctions.

White ecks

Although the CCD image sensors are produced with high-precision technologies,

ne white ecks may be generated on the screen in rare cases, caused by cosmic

rays, etc.

This is related to the principle of CCD image sensors and is not a malfunction.

The white ecks especially tend to be seen in the following cases:

- when operating at a high environmental temperature

- when you have raised the gain (sensitivity)

- when using the slow shutter

Vertical smear

When an extremely bright object, such as a strong spotlight or ashlight, is

being shot, vertical tails may be produced on the screen, or the image may be

distorted.

Aliasing

When ne patterns, stripes, or lines are shot, they may appear jagged or icker.

About a “Memory Stick”

Available types of “Memory Stick” for the unit

You can use “Memory Stick,” “MagicGate Memory Stick” and “Memory Stick

PRO” with the unit. However, because the unit does not support the MagicGate

standards, data recorded with the unit is not subject to MagicGate copyright

protection.

Note

The data recorded with this unit is not compatible with the other units, even if

they support “Memory Stick.”

What is MagicGate ?

MagicGate is copyright protection technology that uses encryption technology.



Before using a “Memory Stick”

Terminal

Write-protect tab

Labeling position

When you set the “Memory Stick” write-protect tab to “LOCK,” data cannot be

recorded, edited, or erased.

Data may be damaged if:

You remove the “Memory Stick” or turn o the unit while it is reading or

writing data.

You use the “Memory Stick” in a location subject to the eects of static

electricity or electric noise.

Notes

Do not attach any other material than the supplied label onto the label space.

Attach the label so that it does not stick out beyond the labeling position.

Carry and store the “Memory Stick” in its case.

Prevent metallic objects or your nger from coming into contact with the

metal parts of the connecting section.

Do not strike, bend, or drop the “Memory Stick.”

Do not disassemble or modify the “Memory Stick.”

Do not allow the “Memory Stick” to get wet.

Do not use or store the “Memory Stick” in a location that is:

extremely hot, such as in a car parked in the sun.

under direct sunlight.

very humid or subject to corrosive substances.

About the Supplied Manuals

Installation Manual (this document)

This Installation Manual describes the names and functions of parts and controls

of the Network Camera, gives connection examples and explains how to set up

the camera. Be sure to read the Installation Manual before operating.

User’s Guide (stored in the CD-ROM)

The User’s Guide describes how to set up the camera and how to control the

camera via a Web browser.

After installing and connecting the camera correctly, operate referring to this

User’s Guide.

Using the CD-ROM Manuals

The supplied CD-ROM disc includes the User’s Guides for this unit (Japanese,

English, French, German, Spanish, Italian and Chinese versions) in PDF format.

Preparations

The Adobe Reader Version 6.0 or higher must be installed on your computer in

order to use the User’s Guide stored in the CD-ROM disc.

Note

If Adobe Reader is not installed, it may be downloaded from the following URL:

http://www.adobe.com/

Reading the manual in the CD-ROM

1 Insert the CD-ROM in your CD-ROM drive.

A cover page appears automatically in your Web browser.

If it does not appear automatically in the Web browser, double-click on the

index.htm le on the CD-ROM.

2 Select and click on the manual that you want to read.

This opens the PDF le of the manual.

Clicking an item in the Table of Contents allows you jump to the relevant

page.

Notes

The les may not be displayed properly, depending on the version of Adobe

Reader. In this case, install the latest version, which you can download from

the URL mentioned in “Preparations” above.

If you have lost or damaged the CD-ROM, you can purchase replacement.

Contact your Sony service representative.

Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the

United States and/or other countries.

Location and Function of Part

Front 

 NETWORK indicator (green)

The indicator lights up or ashes in green when the camera is connected to

the network.

The indicator goes o when the camera is not connected to the network.

 Memory Stick slot

Insert a “Memory Stick” (not supplied) into the slot.

Note

Insert the “Memory Stick” with its front side towards the bottom of the

camera.

 PC card slot

This slot is used for the optional SNCA-CFW1/SNCA-CFW5* wireless card or

recommended ATA memory card.

In case of the wireless card: Insert the SNCA-CFW1 or SNCA-CFW5* into a

commercially available type II-PCMCIA adaptor and insert the adaptor into

the PC card slot.

In case of the recommended ATA memory card: Insert the “Memory Stick”

into the optional PC card adapter and insert the adapter into the PC card slot.

Notes

Insert the PC card with its front side towards the bottom of the camera.

For the veried ATA memory cards, contact your authorized Sony dealer.

 PC card lever

Press the lever to remove the PC card from the PC card slot.

 POWER indicator (green)

When the power is supplied to the camera, the camera starts checking the

system. If the system works normally, this indicator lights up.

 Lens

Note

The four edges of an image may be dark depending on the zoom position.

This is a phenomenon related to the structure of the camera, and does not

cause a problem.

* SNCA-CFW5 is not available in some countries and areas. For details, contact your

authorized Sony dealer.











  

Rear 

 DC IN 12 V/AC IN 24 V (power input) terminal

Connect to a 12V DC or 24V AC power supply system.

 I/O (Input/Output) port

This port is provided with an RS-232C port, two sensor inputs and two

alarm outputs.

Pin No. Pin name

1 Sensor In 1 +

2 Sensor In 1 – (GND)

3 Sensor In 2 +

4 Sensor In 2 – (GND)

5 Alarm Out 1 +

6 Alarm Out 1 –

7 Alarm Out 2 +

8 Alarm Out 2 –

9 GND

10 GND

11 RS232C . RX

12 RS232C . TX

 LAN (network) port (RJ45)

Connect to the 10BASE-T or 100BASE-TX network using a network cable

(UTP, category 5).

  (video output) connector (BNC type)

Outputs a composite video signal.

  (line output) jack (minijack, monaural)

Connect a commercially available speaker system with the built-in

amplier.

  (microphone input) jack (minijack, monaural)

Connect a commercially available microphone. This jack supports plug-

in-power microphones (rated voltage: 2.5 V DC).

 Reset switch

To reset the camera to the factory default settings, supply the power to

the camera, while holding down this switch with a pointed object.

Bottom 

 Ceiling bracket mounting screw holes

When installing the camera on the ceiling, x the supplied ceiling

brackets to these holes.

 Screw hole for fall-prevention wire rope

When installing the camera on the ceiling, x the supplied fall-prevention

wire rope to this hole using the supplied screw M4×8.

(continued on the reverse side)

 2007 Sony Corporation Printed in Japan



Installation

Notes

Do not grasp the camera head when carrying the camera.

Do not turn the camera head manually. Doing so will result in the camera

malfunctioning.

Installing the Camera on the Ceiling 

You can view the image of this camera in the normal direction when the camera

is installed on the ceiling.

Using the supplied ceiling brackets, wire rope and screws, you can utilize existing

junction boxes, etc., to attach the camera to the ceiling.

When you install the camera, always install it on a level ceiling. If you have to

install it on a sloping or uneven ceiling, make sure that the place where you

install it is within ±5 degrees of the horizontal in order to ensure the pan/tilt

mechanism functions properly.

Warning

If you attach the camera in the height such as the wall or the ceiling, etc.,

entrust the installation to an experienced contractor or installer.

If you install the camera on the ceiling, ensure that the ceiling is strong

enough to withstand the weight of the camera plus the ceiling brackets

and then install the camera securely. If the ceiling is not strong enough,

the camera may fall and cause serious injury.

To prevent the camera from falling, make sure to attach the supplied

wire rope.

If you attach the camera to the ceiling, check periodically, at least once

a year, to ensure that the connection has not loosened. If conditions

warrant, make this periodic check more frequently.



Before installation

After deciding the direction in which the camera will shoot, make the required

holes for the junction box, and connecting cables.

Note

The connecting cables cannot be passed through the upper ceiling bracket. A

hole for the wiring is required in the ceiling at the back of the camera where it is

attached to the ceiling.

Installation

1 Attach the fall-prevention wire rope to the junction box in the ceiling.

Use a screw hole and a screw (not supplied) in the junction box to attach the

wire rope.

2 Attach the upper ceiling bracket to the junction box on the ceiling.

Align the holes in the bracket with those in the junction box, and use

appropriate screws (not supplied).

There is a screw hole in the rounded edge of the upper ceiling bracket. Later,

the front of the camera will be aligned with this screw hole. Attach the upper

ceiling bracket paying attention to the direction of the front of the camera.

3 Attach the lower ceiling bracket to the bottom of the camera using the

supplied four screws ( M3 × 8).

Attach also the wire rope to the bottom of the camera using the supplied

screw ( M4×8).

When attaching, align the screw holes on the bottom of the camera with

those in the ceiling bracket, and set the triangular hole in the ceiling bracket

at the front of the camera.

Tighten the screws a little bit at a time in the numbered order shown in the

illustration. After all of the screws are temporarily tightened in the proper

manner, securely tighten each one in turn.

Caution

To attach the ceiling bracket, use only the screws supplied with the

camera. Using other screws may damage the camera.

4 Insert the raised protrusions on the lower ceiling bracket into the spaces

provided in the upper ceiling bracket, and temporarily x them by turning

the camera with lower ceiling bracket clockwise.

5 While pushing up on the front part of the camera, attach it using the supplied

three screws ( M 3 × 8), starting with the screw at position . 

6 Connect the cables to the connectors on the rear of the camera.

7 To use the supplied cable cover, attach the supplied cable cover mounting

bracket to the rear of the camera using the supplied two screws ( M 3 × 8).

Attach the bracket with the at surface downwards.

8 Temporarily attach the cable cover by inserting the raised protrusions on the

cable cover into the gaps at the rear of the upper ceiling cover. Then x the

cable cover using the supplied two screws ( M3 × 8).

To extend the cables through the rear of the cable cover, cut out the thinner

portion of the cover using a cutter knife.

Note

Take proper steps to ensure that the load of the connected cables does not

cause problems.

Removing the camera

1 Remove two screws used to attach the cable cover in step of “Installation” 8

and remove the cable cover.

2 Disconnect the cables from the connectors at the rear of the camera.

3 Remove three screws used to attach the camera in step of “Installation.”5

4 Pushing the entire camera up towards the ceiling, turn the camera

counterclockwise as far as it goes, then pull it out.

Connection

Connecting to the Network 

Connect the LAN port of the camera unit to a router or hub in the network using

the network cable (straight, not supplied).

To connect to a computer

Connect the LAN port of the camera unit to the network connector of a

computer using the network cable (cross, not supplied).

Connecting the Power Source 

Connect the 12 V DC or 24 V AC power supply system to the power input

terminal on the rear of the camera.

Use the 12 V DC or 24 V AC power source isolated from the 100 to 240 V AC.

The usable voltage range is as follows:

12 V DC: 10.8 to 13.2 V

24 V AC: 21.6 to 26.4 V

Use the UL cable (VW-1 style 1007) for 12 V DC or 24 V AC connection.

Recommended power cable

12 V DC

Cable(AWG) #24(0.22 mm) #22(0.33 mm) #20(0.52 mm) #18(0.83 mm)

Maximumcable

length(m (feet)) 4.5 (14.8) 7.5 (24.6) 12 (39) 21 (69)

24 V AC

Cable(AWG) #24(0.22 mm) #22(0.33 mm) #20(0.52 mm) #18(0.83 mm)

Maximumcable

length(m (feet)) 10.5 (34) 16.5 (54) 27.5 (90) 45.5 (149)

Connecting the I/O Cable 

Using the I/O receptacle

While holding down the button on the slot to which you want to connect the

wire (AWG No. 28 to 22) with a small slotted screwdriver, insert the wire into the

slot. Then release the screwdriver from the button.

Repeat this procedure to connect all required wires.

Wiring diagram for sensor input

Mechanical switch/open collector output device

Camera inside

5 V

2.35 kohms

1 or 3 pin

(Sensor In +)

2 or 4 pin (GND)

GND

Mechanical

switch

Open collector

output device

Outside



Wiring diagram for alarm output

Camera inside

5 or 7 pin

(Alarm Output +)

Magnet relay

24 V AC/24 V DC, 1 A

or less

6 or 8 pin

(Alarm Output –)

Outside

5 V

Circuit example

GND

When You Discard the Camera 

For environmental reasons, take out the lithium battery from the camera and

discard it appropriately.

1 Remove the eight screws and detach the bottom panel.

2 Hold the board on which the lithium battery is attached using long-nose

pliers. Then, bend it in the direction of the arrow illustrated to detach the

battery.

WARNING (for service personnel only)

There is danger of explosion if batteries are mishandled.

Dispose of batteries properly in accordance with the manufacturer’s

instructions and all applicable local regulations.

Specications

Network

Protocol TCP/IP, ARP, ICMP, HTTP, FTP (server/client), SMTP

(client), DHCP (client), DNS (client), NTP

(client), SNMP (MIB-2), RTP/RTCP

Compression

Video compression format JPEG/MPEG4/H.264

Audio compression format G.711/G.726 (40,32,24,16 kbps)

Image size 640 × 480 (VGA), 384 × 288, 320 × 240 (QVGA),

160 × 120 (QQVGA)

Maximum frame rate SNC-RX570N/RX550N/RX530N: 30 fps

SNC-RX570P/RX550P/RX530P: 25 fps

Web browser Internet Explorer Ver. 6.0 or later

Available OS Microsoft Windows 2000, Windows XP, Windows

Vista

Computer environments CPU: Pentium 4, 1.5 GHz or higher (Pentium 4,

2.4 GHz or higher recommended)

RAM: 256 MB or more

Display size: 1024 × 768 or more

Maximum user access 20 users

Network security Password (basic authentication),

IP ltering

Homepage customization Starting from a homepage in the built-in ash

memory, an ATA memory card or a “Memory

Stick” possible

Other functions Detection, image trimming, built-in clock, etc.

Camera

Signal system SNC-RX570N/RX550N/RX530N: NTSC color

system

SNC-RX570P/RX550P/RX530P: PAL color system

Image device 1/4 type color CCD

Total picture elements:

SNC-RX570N/RX550N/RX530N:

Approx. 410,000

SNC-RX570P/RX550P/RX530P:

Approx. 470,000

Eective picture elements:

SNC-RX570N/RX550N/RX530N:

Approx. 380,000

SNC-RX570P/RX550P/RX530P:

Approx. 440,000

SNC-RX570N/P SNC-RX550N/P SNC-RX530N/P

Lens 36x (Optical), 12x

(Digital)

f=3.4 to 122.4

mm, F1.6 to 4.5

Horizontal angle:

1.7° to 57.8°

26x (Optical), 12x

(Digital)

f=3.5 to 91 mm,

F1.6 to 3.8

Horizontal angle:

2.2° to 54.2°

18x (Optical), 12x

(Digital)

f=4.1 to 73.8 mm,

F1.4 to 3.0

Horizontal angle:

2.8° to 48°

Minimum

object distance

TELE end:

1,500 mm (59

1/8 inches)

WIDE end:

320 mm

(12 5/8 inches)

TELE end:

1,500 mm (59

1/8 inches)

WIDE end:

320 mm

(12 5/8 inches)

TELE end: 800 mm

(31 1/2 inches)

WIDE end:

290 mm

(11 1/2 inches)

Minimum

illumination 1.4 lx (F1.6/50 IRE) 1 lx (F1.6/50 IRE) 0.7 lx (F1.4/50 IRE)

Horizontal

resolution

NTSC: 530 TV

(WIDE end)

PAL: 530 TV (WIDE

end)

NTSC: 470 TV

(WIDE end)

PAL: 460 TV (WIDE

end)

NTSC: 470 TV

(WIDE end)

PAL: 460 TV (WIDE

end)

Shutter speed 1 to 1/10,000 s

Video S/N 50 dB or more

Mechanism

Pan 360º, endless rotation

Maximum speed: 300° / s

Tilt –90° to 0°

Maximum speed: 300° / s

Interface

Network port 10BASE-T/100BASE-TX, auto negotiation (RJ-45)

I/O port Sensor input : × 2, make contact

Alarm output : × 2, 24 V AC/DC, 1 A

(mechanical relay outputs electrically

isolated from the camera)

Serial interface: ×1 (RS-232C)

Video output VIDEO OUT: BNC, 1.0 Vp-p,

75 ohms, unbalanced, sync negative

PC card slot PCMCIA Type II

Memory Stick slot “Memory Stick”

Microphone input Minijack (monaural)

Plug-in-power supported (rated voltage: 2.5 V

DC)

Recommended load impedance 2.2 khoms

Line output Minijack (monaural), Maximum output level: 1

Vrms

Others

Power supply 12 V DC ± 10%

24 V AC ± 10%, 50/60 Hz

Power consumption 25 W max.

Operating temperature 0 °C to +50 °C (32 °F to 122 °F)

Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)

Operating humidity 20 to 80 %

Storage humidity 20 to 95 %

Dimensions 230 × 160 × 160 mm (9 1/8 × 6 3/8 × 6 3/8 

inches) (h/w/d)

not including the projecting parts

Mass Approx. 2.3 kg (4 lb 14 oz)

Supplied accessories CD-ROM (User’s Guide and supplied programs)

(1)

Upper ceiling bracket (1)

Lower ceiling bracket (1)

Cable cover (1)

Cable cover mounting bracket (1)

Screws M3 × 8 (11)

Screw M4 × 8 (1)

Fall-prevention wire rope (1)

Installation Manual (this document) (1)

B&P Warranty Booklet (1) (SNC-RX570N/RX550N/

RX530N only)

Optional accessories

Wireless card SNCA-CFW1, SNCA-CFW5*

Wireless LAN antenna SNCA-AN1

“Memory Stick” MSX-1GS (1GB), MSX-512S (512MB), MSH-128

(128MB)

* SNCA-CFW5 is not available in some countries and areas. For details, contact

your authorized Sony dealer.

Design and specications are subject to change without notice.

Regular parts replacement

Some of the parts that make up this product (electrolytic condenser, for

example) need replacing regularly depending on their life expectancies.

The lives of parts dier according to the environment or condition

in which this product is used and the length of time it is used, so we

recommend regular checks.

Consult the dealer from whom you bought it for details.









1, 2

6, 7

Front of the

camera Upper ceiling

bracket

Ceiling

Lower ceiling

bracket

M4×8

(supplied)

M3×8

(supplied)

Set the triangular

hole at the front

of the camera.

Upper ceiling

bracket

Lower ceiling

bracket

Ceiling

M3×8

(supplied)



Ceiling

Cable cover

mounting bracket

Ceiling

M3×8

(supplied)

Camera (rear)

LAN

Network cable

(straight, not supplied)

10BASE-T/

100BASE-TX

Hub

Network

to 12 V DC

or 24 V AC



Slotted

screwdriver

Wire

Lithium

battery

Front

Bottom

Unit: mm (inches)

Side (with ceiling brackets)

46 (1 15/16)

Hole 4 – M3 (×4)

160 (6 3/8)160 (6 3/8)

230 (9 1/8)

242 (9 5/8)

Front (with ceilling brackets)

80 (3 1/4) 80 (3 1

) 80 (3 1/4) 191 (7 5/8)10 (13/32)

83 (3 3/8)

Side (with cable cover)

70 (2 7

/8)

Screw hole for

wire rope

83.5 (3 3/8)

ø83.5 (3 3/8)

Hole width

4.4 (3/16) (×2)

Hole 4 –

ø4.4 (3/16)

40°

(Adjustable range:±20°)

45°

Upper ceiling bracket

Fall-prevention

wire rope

Hole for

connecting cables

Fall-prevention wire rope

M3×8

(supplied)

45°

ø88.9 (3

1/2

)

Hole width

4.4 (3

/16) (×4)

ø121.2 (4 7

/8)

Hole width

4.4 (3/

16) (×4)

ø107.3 (4 1/4)

Hole width

4.4 (3/16) (×4)

60 (2 3/8)







Product specificaties

Merk:	Sony
Categorie:	Bewakingscamera
Model:	SNC-RX530P
Kleur van het product:	Wit
Gewicht:	2200 g
Stroomvoorziening:	AC 24 V/DC 12 V
Kleur:	Ja
Ondersteunde videoformaten:	H.264
Minimale belichting:	0.15 Lux
Kijkhoek, horizontaal:	54.2 °
Maximale beeldsnelheid:	25 fps
Brandpuntbereik:	3.5 - 91 mm
Netvoeding:	25 W
Omvang optische sensor:	1/4 "
Type beeldsensor:	CCD
Digitale zoom:	12 x
Optische zoom:	18 x
Camera sluitertijd:	1 - 1/10000 s
Belichtingsinstelling:	Auto (Full auto, Shutter-priority, Iris-priority), Manual, EV compensation, Backlight compensation
Witbalans:	Auto
Aansluitingen:	1 x PC card\n1 x Memory Stick\n2 x Mini-jack
Fotoresolutie(s):	640 x 480
Temperatuur bij opslag:	-20 - 60 °C
Compatibele besturingssystemen:	Windows 2000/XP
Minimale systeemeisen:	Pentium IV 1.5 GHz+\nRAM 256 MB+\nIE 5.5+
Ondersteunde protocollen:	TCP/IP, HTTP, ARP, ICMP, FTP, SMTP, DHCP, SNMP, DNS, NTP
Pan bereik:	360 °
Afmetingen (B x D x H):	160 x 160 x 230 mm
Draai-snelheid:	300 °/sec
Pan snelheid:	300 °/sec
Video uit:	BNC
Lenssysteem:	Auto-focus zoom lens
Bedrijfstemperatuur (T-T):	0 - 50 °C
Bereik kantelhoek:	-90 - 0 °