Sony SNC-EM641 Handleiding

Sony Bewakingscamera SNC-EM641

Lees hieronder de 📖 handleiding in het Nederlandse voor Sony SNC-EM641 (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 109 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

About the Manuals

Safety Regulations (included)

The Safety Regulations describes notes for the secure usage of camera. Be sure

to read it.

Installation Manual (this document)

Describes the names and functions of parts and controls of the Network Camera,

gives connection examples and explains how to set up the camera. Be sure to

read the Installation Manual before operating.

The illustration of SNC-VM641 is used for example purpose.

An I/O cable or power input cable is not supplied for SNC-EM641.

Electronic Instruction Manual (Web)

How to control the camera via a web browser ˎ

How to setup the camera ˎ

Operate the camera referring to the guide above after having installed and

connected the camera properly based on the Installation Manual.

Assigning the IP address

1 Download the installer for “SNC toolbox” to a folder from the download

site.

2 Install the SNC toolbox.

Unzip the ZIP file of the downloaded installer.

Double-click “SncToolbox_Setup.exe.” For details on installing and use refer to

the Application Guide.

3 Assign an IP address.

Assign an IP address using the installed SNC toolbox. For details, see “Using

SNC toolbox” – “Assign an IP address” in the Application Guide.

Tip

SNC toolbox stands for Sony Network Camera toolbox.

Location and Function of Part

Side 

The cables below are not connected when the unit comes from the factory.

SNC-VM641: , , ,    

SNC-EM641: ,  

 Audio cable (supplied)

The connector with the longer cable (SP) is used for the line output connector,

and the shorter cable (MIC) is used for the microphone/line input connector.

SP terminal (minijack, monaural) ˎ

Connect a commercially available speaker system with a built-in amplifier.

MIC terminal (minijack, monaural) ˎ

Connect a commercially available microphone. This jack supports plugin-

power microphones (rated voltage: 2.5 V DC).

 I/O (Input/Output) cable (supplied only for SNC-VM641)

This cable is provided with two sensor inputs and two alarm outputs.

The wires of the cable control the following signals.

Color of wire Name

Red Sensor In 1+

White Sensor In 2+

Black Sensor In – (GND)

Yellow Alarm Out 1+

Brown Alarm Out 1–

Green Alarm Out 2+

Blue Alarm Out 2–

For details on each function and required settings, see the User’s Guide.

For the wiring, see “Connecting the I/O Cable.”

 Power input cable (supplied only for SNC-VM641)

Connect this cable to a 24 V AC or 12 V DC power supply system.

You can screw an extension cable in the connector tip attached at the end of the

cable. ( -1)

 BNC cable (supplied)

Outputs a composite video signal.

 Wiring cover

When you wire indoors, remove this cover and feed the cables through it.

Caution

Take care not to trap the cables between the camera and the ceiling or the wall. If

the cable is trapped, it may cause a fire or electric shock due to breaking.

Inside 

Items and are not supported for SNC-EM641. 

 Camera unit

 MONITOR output jack

Connect this jack to a video input connector of a video monitor. You can adjust

the camera or lens while looking at the image on the video monitor. After

adjusting the camera or lens, disconnect the cable.

 Camera unit mounting screws (2 positions)

Make sure to tighten the screws securely when installing the camera.

 Camera head fixing screw (tilt)

Firstly, loosen the screw and point the camera head in the desired direction, then

tighten the screw to secure in place.

 SD card slot

This slot is used for optional SD memory cards.

Image data in the camera can be recorded to a memory card by inserting it into

the slot.

When inserting, point the contact area at the rating label side (referring to the

illustration), and be sure to insert it completely. ( -1)

This unit is only compatible with SD and SDHC memory cards.

Note

For inquiries regarding verified SD memory cards, contact your authorized Sony

dealer.

 NTSC/PAL switch

Switching the video output.

After setting the switch, reboot the camera unit.

 ZOOM/FOCUS switch

Use this switch to adjust lens’ zoom and focus. Slide the switch lever to select the

desired function.

[W] WIDE: Zoom out

[T] TELE: Zoom in

[N] NEAR: Focus on a nearby subject

[F] FAR: Focus on a distant subject

Hold down the center of the ZOOM/FOCUS switch for a moment to focus

automatically.

 Reset switch

To reset the camera to the factory default settings, hold down this switch with a

point and supply the power to the camera.

 NETWORK indicator (Green/Orange)

The indicator lights up or flashes when the camera is connected to the network.

The indicator is off when the camera is not connected to the network.

 POWER indicator (Green)

When the power is supplied to the camera, the camera starts checking the

system. If the system is normal, this indicator lights up.

 AC / DC IN (power input) connector (SNC-VM641 only)

Connect the supplied power input cable to this connector.

 Rating Label

This label shows the name of device and its electric rating.

 AUDIO connector

Connect the supplied audio cable to this connector.

 Camera head fixing screw (pan)

Firstly, loosen the screw and point the camera head in the desired direction, then

tighten the screw to secure in place.

 mark

Indicates the image direction.

 Lens

 EXT CTRL (external control input/output) connector (SNC-VM641

only)

Connect the supplied I/O cable to this connector.

 LAN network port (RJ-45)

Connect a network cable (UTP, category 5) to this port to communicate with a

network or PoE* system.

For details on connection, see the Instruction Manual of the power supply

equipment.

(*PoE stands for Power over Ethernet. It is pursuant to IEEE802.3af.)

 VIDEO OUT (video output) connector

Connect the supplied BNC cable to this connector.

Preparations

Connecting the Supplied Cables to the Camera 

Before installation, connect the supplied cables to the camera as required for

your usage and wire them.

Connect the cables to the connectors on the camera unit.

Power input cable: to AC/DC IN connector (SNC-VM641 only)

Audio cable

BNC cable

I/O cable (SNC-VM641 only)

Note

Do not pull on any cables forcefully, as a connection may become loose.

Installation

WARNING

If you attach the camera in the height such as the wall or the ceiling, etc.,

entrust the installation to an experienced contractor or installer.

If you install the camera on the ceiling, ensure that the ceiling is strong

enough to withstand the weight of the camera plus the bracket and then

install the camera securely. If the ceiling is not strong enough, the camera may

fall and cause serious injury.

To prevent the camera from falling, make sure to attach the supplied wire

rope.

If you attach the camera to the ceiling, check periodically, at least once a year,

to ensure that the connection has not loosened. If conditions warrant, make

this periodic check more frequently.

Unit: mm (inches)

85.7 (3 3/ )8

83.5 (3 9/ )32

Hole for connecting cables

ø50 (2)

Horizontal mark

Hole for installing the

bracket

Vertical mark

85.7 (3 3/ )8

4-696-253- (1)11

Network Camera

SNC-VM641/EM641

Installation Manual

Before operating the unit, please read this manual thoroughly and

retain it for future reference.

Deciding the Installation Location of the Camera 

After deciding the direction in which the camera will shoot, make the required

hole (ø 50 mm (2 inches)) for the connecting cables using the supplied template.

Then decide the two or four mounting hole positions to install the bracket.

Mounting screws

The supplied bracket is provided with ø 4.5 mm (

inch) mounting holes. Install

the bracket on a ceiling or wall with screws through two or four mounting holes:

two 83.5 mm (3

inches)-pitched holes or four 85.7 mm (3

inches)-pitched

holes. The required mounting screws differ depending on the installation location

and its material. Use commercially-available screws.

Steel wall or ceiling: Use M4 bolts and nuts. (Hexagon head bolt should not be

used.)

Wooden wall or ceiling: Use M4 tapping screws. The panel thickness must be

15 mm (5/ inch) or more.8

Concrete wall: Use anchors, bolts and plugs suitable for concrete walls. (Head

shape of M4 bolt: Pan head screw or hexagon head bolt should not be used.)

Junction box: Use screws to match the holes on the junction box. (Head shape

of screw: ø 7 mm (9/ inch) Height 4 mm (32 3/ inch) or less)16

WARNING

The required mounting screws differ depending on the installation location and

its material. If you do not secure the camera with the appropriate mounting

screws, the camera may fall off.

Installing the Camera 

1 Remove the dome casing.

 Loosen the screw with the wrench (supplied).

 Turn the dome casing anticlockwise, and remove it from the camera unit.

When the screw catches on the screw hole, pull up the screw.

2 Install the supplied bracket on the ceiling or wall.

Refer to “Mounting screws” for screws to be used.

3 Fix the supplied wire rope to the camera unit and the ceiling or wall.

 Fix the wire rope with the supplied M3 screw to the hole for the wire rope

on the bottom of the camera unit.

Pass the wire rope between the wire rope guides.

 Fix the wire rope to the ceiling or wall.

4 Attach the camera unit to the bracket.

 Align the projection on the top and bottom of the camera’s card slot with

the bracket mounting screw hole on the bracket.

Turn the camera unit lightly in the direction of the arrow (clockwise

rotation), then lock the temporary tightening hook of the camera (3

positions).

Turn the camera in the rotational direction until it completely stops and

tighten the camera unit mounting screws in the order of 1, then 2.

Notes

Be sure to tighten the camera unit mounting screws in the order of 1, then 2. ˎ

Otherwise, the camera unit may not be secure and could fall.

If you cannot use screws on a ceiling or wall, or if you want to make the ˎ

camera less conspicuous, use the YT-ICB600 in-ceiling bracket (optional) with

which you can mount the camera on the ceiling.

When you install the camera with the in-ceiling bracket, tighten the fixing

screw on the side brackets to the position. Refer to the in-ceiling bracket 

Installation Instructions for details.

Adjusting the Camera Direction and Coverage 

You can adjust all pan, tilt and rotation positions. There is no screw for rotation

position.

Turn the lens case to rotate the camera.

You can invert the image by using the setting menu.

1 Loosen the camera head fixing screw.

 Loosen the tilt screws (2 positions).

Loosen the pan screws (2 positions).

2 Adjust the camera to turn the lens in the desired direction.

3 Tighten the camera head fixing screw to fix the camera. (4 positions)

4 Slide the ZOOM/FOCUS switch to W/T to adjust the zoom.

5 Hold down the ZOOM/FOCUS switch for a moment to automatically

adjust the focus.

6 Repeat steps 1 to 5 until the coverage and the focus are determined.

Notes

When you adjust the camera head angle without loosening camera head ˎ

fixing screw, an internal part may be damaged.

Be sure to turn off the setting of superimposing when adjusting the focus. ˎ

If you cannot achieve satisfactory focus with holding down the ZOOM/FOCUS ˎ

switch due to the shooting environment, slide the ZOOM/FOCUS switch level

to N/F to focus manually.

Poor focus may also be caused by the dome case assembly. Readjust the focus ˎ

using the system menu.

For details, refer to the User's Guide of the equipment.

Notes

When the dome casing is attached it may be visible in the monitor ˎ

depending on zoom and rotation. Also, distortion might be observed in

images shot outside the specified optical area.

Do not turn the tilt screw more than 360 degrees and pan screw more than ˎ

2-3 turns, as they may become loose and fall out.

Attaching the Dome Casing 

1 Align the notch on the dome casing with the convex part on the rear of

the camera unit, then turn the dome casing in the direction of the arrow.

2 Tighten screws.

3 Remove the protecting film on the dome cover.

Connection

Connecting to the Network

Connect the LAN connector of the camera to a PoE* supported device (such as a

hub) using the network cable (straight cable).

The electrical power is supplied through the network cable. For details, refer to

the instruction manuals of the PoE supported devices.

(* PoE: The acronym for Power over Ethernet. IEEE 802.3af standard compliant

devices.)

For SNC-VM641, it is possible to connect the LAN port of the camera to a router

or hub in the network using a commercially-available network cable.

Connecting the Power Source

The camera can be powered in the following ways.

12 V DC or 24 V AC (Either voltage supported by SNC-VM641 only.) ˎ

Power supply equipment pursuant to IEEE802.3af (PoE* system) ˎ

*PoE means Power over Ethernet.

Note

Do not turn off the camera immediately after turning it on. Wait for at least five ˎ

minutes before turning off the camera.

Do not connect the power input cable if power is supplied by a PoE system. ˎ

Connecting to the power supply equipment pursuant to

IEEE802.3af

The power supply equipment pursuant to IEEE802.3af supplies the power

through the network cable. For details, refer to the Instruction Manual of the

equipment.

Connecting to 12 V DC or 24 V AC source

Connect the power input cable of the camera to a 12 V DC or 24 V AC source.

Use a 12 V DC or 24 V AC source isolated from 100 to 240 V AC. Each usable ˎ

voltage ranges are as follows.

12 V DC: 10.8 V to 13.2 V

24 V AC: 19.2 V to 28.8 V

- In the USA, The product shall be powered by a UL Listed Class 2 Power

Supply Only.

- In Canada, The product shall be powered by a CSA certified Class 2 Power

Supply Only

Use UL cable (VW-1 style 10368) for these connections. ˎ

Recommended cable

DC 12 V:

CABLE (AWG) #24 #22 #20

Max. length (m (feet)) 9 (29.5) 15 (49.2) 23 (75.5)

AC 24 V:

CABLE (AWG) #24 #22 #20

Max. length (m (feet)) 37 (121.4) 63 (206.7) 92 (301.8)

Connecting the I/O Cable (SNC-VM641)

Connect the wires of the I/O cable as follows:

Wiring diagram for sensor input

Mechanical switch/open collector output device

Camera inside

3.3 V

2.2 K

Sensor input +

GND

Mechanical switch

Open collector

output device

Outside

GNDGND

10 K

(GND)

Sensor input −

Wiring diagram for alarm output

Camera inside

Alarm Output +

Magnet relay –

24 V AC

24 V DC,

1 A or less

Alarm Output –

Outside

5 V

Circuit example

GND

Bracket

(supplied)

Ceiling

Projection

Wire rope

Bracket

mounting

screw hole

3, 4





Dome casing

wrench

Ceiling

Temporary

tightening hook

(3 positions)

Wire rope

(supplied)

Temporary

tightening

hook (3

positions)

screw

(supplied)

Camera unit

mounting

screw (2)

Guide

Lens case

mark

Ø148 (5 7/ )8

108 (4 3/ )8

Specifications

Compression

Video compression format JPEG/H.264

Audio compression format G.711/G.726/AAC

Maximum frame rate 60 fps

Camera

Signal system NTSC color system/PAL color system

(switchable)

Image device 1/2.8type CMOS (Exmor R)

Effective number of pixels: Approx. 2,130,000

Synchronization Internal synchronization

Horizontal resolution 700 TV lines (monitor display ratio 4:3)

Video S/N More than 50 dB (Auto gain control maximum

rate 0 dB)

Minimum illumination View-DR Off/VE*Off/Auto gain maximum rate

MAX/30 IRE (IP) /30 fps

F1.2/Color: 0.006 lx, Black & White: 0.005 lx

* VE stands for Visibility Enhancer.

Lens

Focal length 3.0 mm to 9.0 mm

Maximum relative aperture F1.2 to F2.1

View angle 1920 × 1080 (aspect ratio 16:9)

Vertical: 56.9° to 20.1°

Horizontal: 105.3° to 35.6°

Movable angle Pan: −192° to +192°

Tilt: −7° to +75°

Rotation: −99° to +99°

Minimum object distance 300 mm

Interface

LAN port (PoE) 10BASE-T/100BASE-TX, auto negotiation (RJ-45)

I/O port (SNC-VM641 only) Sensor input: × 2, make contact, break contact

Alarm output: × 2, 24 V AC/DC, 1 A

(mechanical relay outputs electrically isolated

from the camera)

SD memory card slot

Video output VIDEO OUT: BNC, 1.0 Vp-p, 75 ohms,

unbalanced, sync negative

Microphone input* Minijack (monaural)

Plug-in-power supported (rated voltage: 2.5 V DC)

Recommended load impedance: 2.2 kΩ

Line input* Minijack (monaural)

* The microphone input and the line input are switchable with operating menu.

Line output Minijack (monaural), Maximum output level:

1 Vrms

Others

Power supply SNC-VM641:

12 V DC ±10%

24 V AC ±20% 50 Hz/60 Hz

IEEE802.3af compliant (PoE system)

SNC-EM641:

IEEE802.3af compliant (PoE system)

Power consumption 6.0 W max.

Operating temperature Start temperature: 0°C to 50°C (32°F to 122°F)

Working temperature: −10°C to +50°C (14°F to

122°F)

Storage temperature –20°C to +60°C (–4°F to +140°F)

Operating humidity 20% to 80% (no condensation)

Storage humidity 20% to 80% (no condensation)

Dimensions (diameter/height) 

148 mm × 108 mm (5 7/ inches × 4 83/ inches)8

Mass Approx. 835 g (1 lb 13 oz) (excluding cable or

bracket)

Supplied accessories Bracket (1), Template (1), Wire rope (1), Camera

unit mounting screw M3 (1), Wrench (1), Audio

cable (1), BNC cable (1), Safety regulation, I/O

cable (1) (SNC-VM641 only), Power input cable

(1) (SNC-VM641 only)

Optional accessory

In-ceiling bracket YT-ICB600*

* Using the fixture position on the bracket.

Dome Cover Smoked YT-LD601S

Design and specifications are subject to change without notice.

Unit: mm (inches)

Product specificaties

Merk:	Sony
Categorie:	Bewakingscamera
Model:	SNC-EM641
Kleur van het product:	Black, White
Gewicht:	835 g
Hoogte:	108 mm
Soort:	IP-beveiligingscamera
Gebruikershandleiding:	Ja
Maximale capaciteit van de geheugenkaart:	256 GB
Stemcodecs:	G.711, G.726
Vormfactor:	Dome
Ondersteuning voor plaatsing:	Binnen
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Montagewijze:	Plafond
Maximum resolutie:	1920 x 1080 Pixels
Totaal aantal megapixels:	2.13 MP
Videocompressieformaten:	H.264
Diameter:	148 mm
Type stroombron:	Power over Ethernet (PoE)
Minimale belichting:	0.005 Lux
Aantal cameras:	1
Meegeleverde kabels:	BNC
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	SD
Nachtvisie:	Nee
Video bewegings-detectie:	Ja
Zoomcapaciteit:	Ja
Microfoon, line-in ingang:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	1
Brandpuntbereik:	3 - 9 mm
Certificering:	UL2044, IEC60950-1, VCCI, FCC, IC, EN55032, EN55024, EN50130-4, AS/NZS CISPR32, KC, EMC-TR
Formaat analoog signaal:	NTSC, PAL
Volledige HD:	Ja
Omvang optische sensor:	1/2.8 "
Beeldstabilisator:	Ja
Type beeldsensor:	CMOS
Digitale zoom:	4 x
Optische zoom:	3 x
Camera sluitertijd:	1 - 1/10000 s
Witbalans:	ATW, Fluorescent, Manual, Mercury lamp, One push, Sodium lamp
Ondersteunde grafische resoluties:	352 x 288,640 x 360,640 x 480 (VGA),704 x 576,720 x 480,720 x 576,1024 x 576 (WSVGA),1280 x 720 (HD 720),1920 x 1080 (HD 1080)
Webbrowser:	Ja
Ruisonderdrukking:	Ja
Bekabelingstechnologie:	10/100Base-T(X)
Netwerkstandaard:	IEEE 802.1x, IEEE 802.3af
Ondersteunt Windows:	Windows 10, Windows 7, Windows 8.1
Aantal gebruikers:	20 gebruiker(s)
Temperatuur bij opslag:	-20 - 60 °C
Veiligheidsfunties:	Vandaalbestendig
Maximaal 30 frames per seconde:	60 fps
Ondersteunde netwerkprotocollen:	IPv4, TCP, UDP, ARP, ICMP, IGMP, HTTP, DHCP, DNS, NTP, RTP/RTCP, RTSP over TCP, SMTP over HTTP, IPv6, HTTPS, FTP (client), SNMP (v1, v2c, v3), SSL
Luchtvochtigheid bij opslag:	20 - 80 procent
Frequentiebereik:	16000 - 48000 Hz
Progressive scan:	Ja
Ethernet interface type:	Fast Ethernet
Signaal/ruis-verhouding:	50 dB
Ondersteunde talen:	ARA, CHI (SIMPL), CHI (TR), DEU, ENG, ESP, FRE, HIN, ITA, JPN, KOR, POR, RUS, THA
Quality of Service (QoS):	Ja
Power over Ethernet (PoE):	Ja
Inclusief schroeven:	Ja
Dichtstbijzijnde focus afstand:	0.3 m
PTZ control:	Ja
Minimale processor:	Intel Corei7 2.8 GHz
Draaihoek:	198 °
Pan bereik:	-192 - 192 °
Dag/nacht modus:	Ja
Maximum aperture number:	2.1
Minimum aperture number:	1.2
Methode voor streaming:	Multicast
BNC output ports:	1
Lens type:	Varifocaal
Aantal talen:	17
Bitratecontrole:	Constant Bit Rate (CBR), Variable Bit Rate (VBR)
Stroomverbruik (voeding via Ethernet (PoE)):	6 W
Bitrate:	64 Kbps - 32 Mbps
Bedrijfstemperatuur (T-T):	-10 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 80 procent
Bereik kantelhoek:	-7 - 75 °
Privézone maskeren:	Ja
Systeemfuncties intelligente videobewaking (IVS):	Abandoned object, Face detection, Missing object
Kijkhoek lens, horizontaal:	105.3 °
Lens mount interface:	CS-aansluiting
Kijkhoek lens, verticaal:	56.9 °
Automatische versterking control:	Ja
Iris:	Ja