Solid State Logic VHD+ Pre 500 Series Handleiding

Solid State Logic Receiver VHD+ Pre 500 Series

Lees hieronder de 📖 handleiding in het Nederlandse voor Solid State Logic VHD+ Pre 500 Series (1 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 90 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Introduction
Congratulations on your purchase of this API 500 format compatible
SSL VHDTM Pre Module.
This module has been specically designed to operate in a 500 format
rack such as the API lunchbox® or equivalent. In common with many
such modules, the nominal input/output level is +4dBu.
The VHD Pre is an immensely versatile recording and processing
device. It can deliver ultra clean SSL SuperAnalogue TM grade
recordings but also features a switchable VHD mode. SSL’s patented
Variable Harmonic Drive (VHD) system uses a 100% analogue signal
path to generate rich harmonic distortion. As you increase VHD input
gain, the Variable Harmonic Drive process introduces either 2nd or 3rd
harmonic distortion or a blend of the two to your source material. At
lower gain settings it adds gentle valve-style warmth or a touch of
transistor edge. As the gain is increased the more extreme the
distortion becomes until at high gain settings it delivers erce trashy
transistoresque grunge.
Operation
Please refer to the illustration opposite.
Signal LED
The signal LED is a tri-colour LED that indicates level according to the
following table.
* The LED scale is selected from a jumper on the module PCB.
Gain Controls
The red pot provides up to +75 dBs of gain, whilst the black pot
provides a variable mix of 2nd to 3rd harmonics (once the VHD-IN
switch is engaged).
The grey pot provides +/- 20dB of trim. Use this to control the output
when driving the VHD preamplier circuit.
High Pass Filter
The High Pass Filter section is a switchable 18dB/Octave variable
lter. See the block diagram for the position in the circuit.
Switch Functions
HI-Z Switches the preamplier impedance from 1.2KΩ to
10KΩ
+48v Applies phantom power, a tell tale red LED indicates
phantom power is active.
PAD Applies 20 dBs attenuation before the signal enters the
preamplier.
Ø Polarity switch inverts the polarity of the signal by 180°.
Using the preamplier
When the VHD button is not engaged, the preamplier has been
designed to give a transparent sound, great for sources such as
acoustic guitars, vocals and strings.
When the VHD button is pressed, the preamplier can be driven to
give a wide-range of overdriven sounds, ranging from subtle to... well,
not so subtle! Drums and electronic instruments can oen benet
from VHD colouration.
The best way to drive the VHD preamplier is to increase the input
gain (red pot) whilst using the Line Trim pot to reduce the overall level
and not clip the channel output. Remember, it’s the input to the
preamplier that likes being driven. From this point, adjust the
harmonics to ne-tune the desired sound.
Block Diagram
Signal LED
VHD In
Switch
High Pass
Filter
Gain Controls
Switch
Functions
LED colour
LED colour
LED colour
LED colourLED colour +24dB Sc
+24dB Sc
+24dB Sc
+24dB Sc+24dB Scale*
ale*
ale*
ale*ale* +18dB Sc
+18dB Sc
+18dB Sc
+18dB Sc+18dB Scale*
ale*
ale*
ale*ale*
Green -24dBu -24dBu
Yellow +4dBu 0dBu
Red +21 dBu +16dBu


Product specificaties

Merk: Solid State Logic
Categorie: Receiver
Model: VHD+ Pre 500 Series

Heb je hulp nodig?

Als je hulp nodig hebt met Solid State Logic VHD+ Pre 500 Series stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Solid State Logic

Handleiding Receiver

Nieuwste handleidingen voor Receiver

Akg

Akg IVM4500 IEM Handleiding

14 November 2024
Yamaha

Yamaha XMV8140 Handleiding

14 November 2024
Yamaha

Yamaha TX4n Handleiding

14 November 2024
Yamaha

Yamaha XMV4140 Handleiding

14 November 2024
Yamaha

Yamaha PC6501N Handleiding

14 November 2024
Yamaha

Yamaha PC3301N Handleiding

14 November 2024
Yamaha

Yamaha PC4801N Handleiding

14 November 2024
Yamaha

Yamaha P1000S Handleiding

14 November 2024